2aHawaii
Tools and Uses => Reloading => Topic started by: ImKu on January 10, 2014, 10:44:48 AM
-
What mistakes have you made that you have leaned upon and established procedures or something to prevent it from happening again? What tricks have you found along the way?
I use a turret press.
Here is my list:
1. I was about to set primers when I remembered that I forgot to check headspace. All 250-300 pieces of brass needed to be re-sized.
I now have a printed procedure on my reloading bench, just so I don't forget that again
2. I was goingt to start decapping my spent casings in my decapping die, but when I put the case through the press I got a stuck case. I accidentilly lined up my FL sizing die.
PAYING ATTENTION would have prevented this. I now labled my dies (even though they don't even look the same...)
3. I added walnut media and the casings into the tumbler and then added brass polish after. After 2 - 2 1/2 hours I found a that majority of the primer pockets had a hard residue.
I now add my brass polish to my media and let it run for 10-15 minutes and then add the brass after.
4. After I am done tumbling in walnut media, I use a media separator. After the brass is covered in dust.
I now add about 3-4 used drier sheets and they collect most of the dust
5. I had 50 cases filled with powder that I was about ready to start seating bullets into when I accidently pulled a cloth that the tray was on and spilled poweder.
I now seat a bullet as soon as I add powder to prevent this from happening
One of the biggest things that I try NOT to do is become complacent. I can recall a few times where I caught things that were not right further down the line of loading than I would have liked. (found a few cases with different headstamps right before I was about to start setting primers).
So, what have you learned?
-
I used the same load with different brand of brass and a different type bullet. (.308win)
Although the bullet weight was the same, the shape and type of bullet was different. What happened was the pressures created by the same charge was too much for the weaker brass to handle. I got primer blow by and etched the bolt face some. While disater was avoided, the bolt face on my nice custom action is now ugly. Lessen learned, never change any part of the load or components without redoing a work-up to that load. Lucked out on that one. :o
-
Don't Ever put a small flake type powder inside the RCBS Chargemaster powder dispenser. As it turns out, it superbly measures a power charge. However, trying to cleanout the powder when you are done is a royal PITA!! Haha Don't do it! LOL
-
I ignore my wife because she makes me lose my train of thought.
I put my finger over the mouth of the case when i put it in the press to seat a bullet.
I have a big sign that says prime because there has been several times when i finish charging cases and pick one up to seat a bullet and the powder pours out the primer hole.
-
i just started reloading but i see a lot of lessons being learned in my future >:(
#1 changing dies but forgetting to change the shell plate during my sizing runs. the first brass got stuck in the sizing die and the shell plate for the larger caliber naturally didnt grab the rim and pull the case out.
#2 using the tap too hastily when trying to remove the brass using a stuck brass kit. i figured brass is nice and soft and would be much easier than trying to tap stainless steel.
#3 not using gloves when handling my dies or any other carbon steel parts. even when i lightly spray everything down with hornady one shot after im pau i sometimes still get rusty fingerprints here and there.
-
Instead of using a dipper and a trickler to powder charge, using a RCBS Chargemaster 1500 Powder Scale and Dispenser Combo speeds up the process and IMO makes reloading even more enjoyable. Just busted it out last night and was very happy. Don't think about it, just get one. You'll thank me later.
-
Test chamber the first few completed rounds in a gauge or the gun and magazine to make sure they actually fit in the gun and magazine.
It is possible to load ammo that goes into the gun but does not fit in the mag.
-
What Oldfart said +1. And if you change to using new dies then double check everything in a chamber gauge again.
-
If you're loading on a 550B, try not to let that ball bearing under the shell plate roll into the hole in the middle of the press. The hole is the perfect size for it to happen, and it can be a pain to get the ball out, especially if you've got primers and powder loaded up in the press.
If it does roll down that stupid hole, avoid using the small round magnet (from the back of the present that one of your kids gave you) attached by duct tape to either a string or a broken chopstick, to try to fish it out of the hole. It will probably get stuck to one side of the tube and you'll then have to fish that out. A much better option is your wife's eyebrow pluckers grasping firmly to that magnet (that had gotten stuck by trying the previously mentioned tactic), to get the ball bearing out.
Or, on a much simpler but not quite as fun note, I've read (after the above-mentioned fiasco), that a 1911 recoil spring is the perfect size to grab the ball bearing from the evil clutches of that Dillon ram hole.
-
Always write down what you've loaded on a label and include the date.
About the only problem I had with my reloads is this: Years ago I took a few boxes of reloaded 7mm Magnum to a big island ranch and shot some of it at high altitude (we were almost in the clouds that day).
About 10 years later I shot a round from the remaining box at Koko Head and experienced high pressure signs--I had to use a rubber mallet to open the bolt, fortunately I didn't break off the bolt handle. I stopped firing that ammo and put it aside. Later, I broke down the loads and the bullets had severe corrosion inside the neck area. Some of the loads had greenish powdery residue (corroded gilding metal) mixed in with the powder. I guess the high humidity and perhaps the altitude allowed some moisture to condense on or in the loads, and the different metals accelerated the corrosion process.
Ammo that I had loaded a year or two later (and did not travel to the big island) were fine--no problems.
I kept the bullets as a reminder to myself and scrapped the rest. BTW, old powder makes an interesting weed killer.
Lesson learned--I guess if something goes wrong with your loads, STOP! then check it out. Lesson 2--don't rely on reloads for a hunting trip. The cost of a box or two of good factory cartridges is minimal compared to the cost of transportation, fees, lodging, etc., so saving a few bucks by rolling your own isn't really worth it.
-
Molten lead is hot. It hurts. Don't get it on your hands.
-
Here's one I learned today. Do NOT touch primers with your hands. I dropped (2) two primers and picked them up with my hand while I was loading. Out of the 50 rounds that I shot, I had (2) FTF with good primer strikes. I asked one of the RO's at the range today who from talking with before was a long time reloader. He said that the oils on your hand contaminate the primer causing a misfire sometimes. Lesson learned, pick up dropped primers with some tweezers or something.
-
Here's one I learned today. Do NOT touch primers with your hands. I dropped (2) two primers and picked them up with my hand while I was loading. Out of the 50 rounds that I shot, I had (2) FTF with good primer strikes. I asked one of the RO's at the range today who from talking with before was a long time reloader. He said that the oils on your hand contaminate the primer causing a misfire sometimes. Lesson learned, pick up dropped primers with some tweezers or something.
Not sure about that one. Unless its a certain brand of primer. I handle every single one of my primers. It is necessary on my press (Forster Co-ax press) to load each by hand. Well, not necessary but I don't want to fiddle with tweezers, I'd lose my mind. I never had a misfire yet. Might be more to do with seating them all the way down into the pocket. I ream all my brass's primer pockets square(Sinclair pocket reamer with drill adapter), and clean them with the reamer after each firing to get the carbon out of the corner. I also make sure that the primers are seated all the way down, which is easy to do with the Forster Co-ax press. Since I've began using this step, I have not had a misfire.
-
Interesting. I guess it could be coincidence that I touched the same amount that misfired. I'm using Fed Gold Metal Match #210. I use a Lee turret press to seat the primers, so I rarely need to actually touch any primers unless I drop them out the box. For brass prep I use the RCBS primer pocket uniformer and all rounds are visually checked to ensure that the primers are fully seated.
(http://i1285.photobucket.com/albums/a586/ImKu/Mobile%20Uploads/20140209_201134-1_zpsvnf2qflx.jpg) (http://s1285.photobucket.com/user/ImKu/media/Mobile%20Uploads/20140209_201134-1_zpsvnf2qflx.jpg.html)
(http://i1285.photobucket.com/albums/a586/ImKu/Mobile%20Uploads/20140209_201415-1_zpsm99jnn1f.jpg) (http://s1285.photobucket.com/user/ImKu/media/Mobile%20Uploads/20140209_201415-1_zpsm99jnn1f.jpg.html)
Guess which one is the one that was shot :geekdanc:
(http://i1285.photobucket.com/albums/a586/ImKu/Mobile%20Uploads/20140209_201440-1_zps0vrefxim.jpg) (http://s1285.photobucket.com/user/ImKu/media/Mobile%20Uploads/20140209_201440-1_zps0vrefxim.jpg.html)
-
I used to use the lee press to seat, it works the arms too much. hehe. looks seated down to me, I could be wrong.
-
This is quite the mystery here. I use Federal and CCI primers almost exclusively. I touch them during reloading and I have never had a failure with Federal and have had only one or two with CCI. I use CCI for pistol and Federal and Federal Match for rifle. I have a friend who bought some Magtech primers and he has had a few failures with them. But has never had a failure with Remington and Winchester primers. While I have a tendancy to think it is just coincidence you could try and test your theory. While reloading also load a few empty cases with primers you have touched. Next time you go shooting just fire the empty cases and see if you get any failures.
-
I forgot to suggest to take the failed rounds apart and remove the primers and look in the primer pocket. If the primer pocket is clean the primer failed. If it is blackened then it might have been a low ignition issue or a blocked primer hole.
-
Since I believe that the primer did not ignite (I thought that I may have not loaded a round at first), I really don't want to de-cap a potentially live primer... Isn't there a chance that I could set it off? I was probably going to soak it in water for a while prior to de-capping. The fact that you and Heavies both say you handle your primers leaves me clueless as to what may have caused the FTF because that pretty much rules out handling primers as a cause. I have never had any issues reloading until yesterday. I store my primers in a container with desiccant. Up till now, I use exclusively Fed Match #210. Thanks for your input guys.
-
The only time I have had problems with misfires in rifle, I was using the Lapua small rifle primer case (.308), heavy powder charge, and heavy bullet (185grn BTLR Berger). After I pulled the bullet I discovered the primer had fired, however, the powder did not fully ignite. I figured the small primer did not have enough 'flash' to bust through the nearly packed powder to reliably ignite the powder charge.
Also, the Lapua smalll rifle .308 brass has a reduced size flash hole, which I believed to exacerbate the problem.
My solution was to ream the flash hole a tad larger. Seems to have worked since, and as a bonus, it seems to have reduced my ES/SD of that particular load a bit.
With your large primer brass, perhaps the federal primers, known to be a particularly mild flash primer, may be having a similar issue. Maybe a clean up of flash hole, since the hole is already large, or a change in primer brand might resolve the issue. Also, check for cleaning media in there before you load. It likes to block that tiny puka, it seems. :D
I have had great results with wolf or pmc LR non magnum primers for precision work. And they are cheap to boot.
-
I'm using Lapua .308 brass. It was near the max. recommended (using Varget) but not a compressed load. I do a thorough inspection of the brass prior to loading and have never had a burr of anything in the flash hole before, and never really wanted to mess with it either...lol I may change my mind in the future. Thx again for your inputs.
I plan on loading another 50 or so and see if the issue reappears as I found a nice load for the 175 SMK with decent SD (7) and ES (22) with a average of 2716 fps.
-
It's up to you but I have deprived live primers before. Just go slow with them. I have even reused them without failures. I only reuse those have not been struck. I did have one go off while depriming. I even stepped on one with my slippah and while a little startling it was not a big deal. Just make sure you wear safety glasses like you should any ways.
-
I forgot to suggest to take the failed rounds apart and remove the primers and look in the primer pocket. If the primer pocket is clean the primer failed. If it is blackened then it might have been a low ignition issue or a blocked primer hole.
My findings update: pulled the FTF rounds and the primer pocket was clean... I did a "test" and handled a (2) primers with my hands, loaded them with my batch and put them on the side to shoot and they both shoot fine. I am not sure what caused the FTF on the previous range session, but could not replicate the issue. Thank you for those that chimed in.
*on a side note if anyone has a Bergers Reloading manual can you PM me? I would like some load data for 185gr target Berger .30 cal (min and max charges) without having to purchase the manual as I could not find the info online. Thanks :shaka: