2aHawaii

Tools and Uses => Reloading => Topic started by: vooduchikn on April 27, 2011, 04:05:37 PM

Title: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on April 27, 2011, 04:05:37 PM
I would like to start this thread for all of you with  your favorite .45 reloads.

There is tons of data out there, some good, some not so good.

Looking forward to hearing what you all have to say and sharing what I am learning. 
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on April 28, 2011, 05:25:38 AM
Bullseye folks will use 3.8 grains of Bullseye powder and 200 grain lead semi wad cutters.
Very accurate, soft shooting, but very dirty.
Carbon on everything. Makes me think of the black powder thread going on in the other section.  :D
 I use this for general plinking and practice; saves wear and tear on the pistol.

4.8 to 5 grains of BE and 230 grain FMJ is said to mimic government ball ammo pretty well.

I've been running 5.5 grains of BE under 185 grain montana gold JHP's for extra SD loads, in case I run out of factory SD ammo.  It has been said it is a bad idea to use handloads for SD, but if you gotta, you gotta.
This is definitely a full house load.

As always, look at your reloading manual and work up carefully.

I'd change powders, but I have about 7.8 lbs of an 8 pound keg left. This is after loading hundreds and hundreds of rounds of .45acp. Hehe :P
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: 808shooter on April 28, 2011, 09:19:52 AM
Haven't got too much into experimenting with different  45 acp  recipies yet.  I"m using 4.2gr Bullseye with 200gr. RN, CCI large primers and mixed headstamp cases and it's doing very well so far.  It is ejecting the cases straight up into the air from my 1911 however, and that is pretty irritating.  Anyone know what that indicates?

As always, read your manuf. load data and don't take my info as correct.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on April 28, 2011, 09:55:42 AM
Haven't got too much into experimenting with different  45 acp  recipies yet.  I"m using 4.2gr Bullseye with 200gr. RN, CCI large primers and mixed headstamp cases and it's doing very well so far.  It is ejecting the cases straight up into the air from my 1911 however, and that is pretty irritating.  Anyone know what that indicates?

As always, read your manuf. load data and don't take my info as correct.

How does it eject with normal full power factory loads?

If it ejects normally with factory, you might need to swap out your recoil spring for a lighter one.
I most parts places sell kits with various poundage springs. I know WGS has springs at their shop.
Just swap for one that'll make the gun work right for plinking, and put the stock heavy spring back in when you are done, for those full power SD loads.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: 808shooter on April 28, 2011, 10:31:45 AM
it's a brand new 1911 so maybe little tight yet.  Yes, factory ammo ejects over the shoulder. 

So if I were to go to say, 4.0gr of BE or even 3.8, maybe the brass would just dribble out, or not cycle at all?

Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on April 28, 2011, 11:32:30 AM
it's a brand new 1911 so maybe little tight yet.  Yes, factory ammo ejects over the shoulder. 

So if I were to go to say, 4.0gr of BE or even 3.8, maybe the brass would just dribble out, or not cycle at all?



Haha. Yeah probably.
Mine is an old well broken in Colt, so it cycles no problem.
If you go by WGS, try asking them about it. They have springs in various LBS.
Stock is around 16lbs, so that and the fact that the gun is nice and tight is what's probably giving you the problems with light loads.
A lighter spring and a well lubed slide might be worth a try.
Just don't forget to switch back before shooting full power.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on April 28, 2011, 12:53:01 PM
The load we are going to test on on Saturday is:

Winchester WST (4.2 gns)  230 gn FMJ, wolf primers, OAL 1.26, crimp .471.

These easily cycle by hand in my Commander. I expect they will do the same in my buddies full size.

Will post findings. I expect to raise the power factor after these depending on how they shoot.  These are plinking loads. Going to work on target loads when I ensure I can replicate my my recipes.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 01, 2011, 09:15:39 PM
The load we are going to test on on Saturday is:

Winchester WST (4.2 gns)  230 gn FMJ, wolf primers, OAL 1.26, crimp .471.

These easily cycle by hand in my Commander. I expect they will do the same in my buddies full size.

Will post findings. I expect to raise the power factor after these depending on how they shoot.  These are plinking loads. Going to work on target loads when I ensure I can replicate my my recipes.

Tested these out today on the range. No failures to fire or over charged loads. I have a few (4)  fail to feeds in my Colt Commander. My buddy had zero issues in his full size colt. I attribute this to the fact that my recoil spring is stiffer than his.

The loads felt very light as compared to Speer Law Man factory ammo. The difference was very noticeable. I had no issues with shooting the Speer through my Commander. The OAL on our reloads as compared to the factory was almost the same with a slight variation amongst the group. I think this is due to using mixed headstamp brass.

Came home and reloaded another batch of 200, and upped the charge from 4.2 to 4.7gns of Winchester WST.   Will be out there next weekend to run this batch through our Colts and see how they shoot.

The WST shot very cleanly. There was no unburnt powder in the cases. All the guys i talked that reload have said to use "Bullseye" powder. Anyone on here have experience with this brand?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on May 04, 2011, 03:59:59 AM

Quote
The WST shot very cleanly. There was no unburnt powder in the cases. All the guys i talked that reload have said to use "Bullseye" powder. Anyone on here have experience with this brand?

That's the powder I was talking about.  It is what the bullseye target shooters use, it is accurate but very, very dirty. It leaves grey soot all over the place.  It is not hard to clean up, but it makes a mess.  If you want to try some LMK I'll give you some.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Teichi on May 04, 2011, 05:34:14 AM
I use Bullseye for 9mm, .45, and .38. I bought an 8lb keg as part of my Y2K stash. It is very consistent at target velocities. I'll try Tite Group when I use it up. I'll need another 8lb keg for my 22 Dec 2012 stash.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 04, 2011, 09:49:38 AM
I'll need another 8lb keg for my 22 Dec 2012 stash.


 ;D

Thanks for the info..and the reminder.  I may have to try some.

Anyone try WST in 9MM?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: mnpfamily on May 04, 2011, 06:53:53 PM
Have not used WST, but I have used Titegroup for 9mm under 147grn CMJ from MG for MPPL matches.  Very soft, fairly cheap, but pretty dirty.  Have recently switched to VV N320 under the same bullet, OAL, brass, primers, and it seems to make for a  somewhat softer, different recoil feel.  About $10 more expensive per pound though.  Thinking about switching back to TG, however the VV is a lot easier to see in the case when it comes out of Sta.2 on my press.  Either way, reloads are way cheaper than the factory 124grn, Amer Eagles we were using for practice/matches.   
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 04, 2011, 06:59:58 PM
, however the VV is a lot easier to see in the case when it comes out of Sta.2 on my press.

This.

I am always looking at my station 3 to gauge the charge for a double. I have noticed it is nearly impossible to do on the XL650...BUT I always look.

Title: Re: .45 ACP LOAD - "RECIPES"
Post by: mnpfamily on May 04, 2011, 08:26:02 PM
Don't know much about the 650, but with my 550, I've been able to situate my workstool so that I can see not only Sta2 (powder drop) but also the primer slide as it returns from picking up a fresh primer(had some issues early on).  Haven't had to set-up a mirror or light yet as I reload during the day in my garage so I can readily see into the case after the powder drop, however I've been considering it as an added safety measure. 
I've been following this thread a bit as I'm about to start reloading .45 after reloading approx. 5000 or so rounds of 9mm (got my Dillon 550 as Christmas present from my wife this past Dec.) and I'm always looking for more info.  Just got 1000 pcs. .45 brass that I ordered from Starline, and am waiting on my .45 bullets from MG. 
Just a heads up, I've read a bit about primer issues with the 650, eye pro is essential as it always is when reloading.  Also, +1 on the post that reminded to check for bullet setback.  I had that issue early on also.  Not too good when shooting action pistol as you don't always end a stage with an empty mag, and I started worrying that the round that was on top at the "unload and show clear" command would somehow be the same one after each stage.  My wife and I started pulling that ejected round and saving it to check OAL before using it again.  Safety first.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 04, 2011, 08:43:48 PM
Don't know much about the 650, but with my 550, I've been able to situate my workstool so that I can see not only Sta2 (powder drop) but also the primer slide as it returns from picking up a fresh primer(had some issues early on).  Haven't had to set-up a mirror or light yet as I reload during the day in my garage so I can readily see into the case after the powder drop, however I've been considering it as an added safety measure. 
I've been following this thread a bit as I'm about to start reloading .45 after reloading approx. 5000 or so rounds of 9mm (got my Dillon 550 as Christmas present from my wife this past Dec.) and I'm always looking for more info.  Just got 1000 pcs. .45 brass that I ordered from Starline, and am waiting on my .45 bullets from MG. 
Just a heads up, I've read a bit about primer issues with the 650, eye pro is essential as it always is when reloading.  Also, +1 on the post that reminded to check for bullet setback.  I had that issue early on also.  Not too good when shooting action pistol as you don't always end a stage with an empty mag, and I started worrying that the round that was on top at the "unload and show clear" command would somehow be the same one after each stage.  My wife and I started pulling that ejected round and saving it to check OAL before using it again.  Safety first.

I use eye protection. No need for rumors about primers going off for me...you are building a bullet, thats enough to convince me.,

I am currently loading .45 and have tons of 9mm brass that I plan on reloading as well (40 SW bullets on the way as well) The overall endgame here for us is to be able to shoot out there at an MMPL event  or something like it as often as I want, for as cheap as I can, and have control of the ammunition specs.

Once i know I can reload consistently (soon) I plan on taking a 101 and getting into the game.

Any thoughts on best way in?

Title: Re: .45 ACP LOAD - "RECIPES"
Post by: mnpfamily on May 04, 2011, 09:35:02 PM
As some ad person once said, "Just Do It".   My wife and I try to catch one of the MPPL matches a month, and we enter mostly for fun.  The gun manipulation aspect is important, however we're there to do what we aren't allowed to do at the bullseye range.  We started out with factory ammo, and have progressed to "rolling our own".  We have learned a ton in the short time we've been involved, however the lessons have been very eye opening.  Our goals are: be safe, have fun, learn something.  We have not been let down at any of the matches we've entered. 
Don't feel that you have to wait until you're reloading a specific caliber to sign up for 101.  Yes you'll save a bunch of money if you do reload and your times will be faster than with factory ammo, but its fun anyway.  Check out MPPL.net, they have all the info you'll need to sign up and get started.  (I belive that's the website, if not just google Mid Pacific Pistol League and it should lead you there.)  Don't even bother with USPSA membership until you know you want to really get into it. 
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 04, 2011, 09:43:33 PM
As some ad person once said, "Just Do It".   My wife and I try to catch one of the MPPL matches a month, and we enter mostly for fun.  The gun manipulation aspect is important, however we're there to do what we aren't allowed to do at the bullseye range.  We started out with factory ammo, and have progressed to "rolling our own".  We have learned a ton in the short time we've been involved, however the lessons have been very eye opening.  Our goals are: be safe, have fun, learn something.  We have not been let down at any of the matches we've entered. 
Don't feel that you have to wait until you're reloading a specific caliber to sign up for 101.  Yes you'll save a bunch of money if you do reload and your times will be faster than with factory ammo, but its fun anyway.  Check out MPPL.net, they have all the info you'll need to sign up and get started.  (I belive that's the website, if not just google Mid Pacific Pistol League and it should lead you there.)  Don't even bother with USPSA membership until you know you want to really get into it.

I have been lurking the website. I know for a fact that I want to shoot competitively...mostly for the fun and practice. I just haven't had the time to get into it. Going to have to make the time.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Dregs on May 04, 2011, 09:53:27 PM
I have to deliberately request off to catch their next 101 on 5/22 O_o. Hopefully I get it.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on May 04, 2011, 10:00:39 PM
I have to deliberately request off to catch their next 101 on 5/22 O_o. Hopefully I get it.

I think I will be out to sea that day..GRRRR..ANOTHER MISS!  ;D
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: astroboy on September 11, 2011, 09:29:14 PM
I load 5.0 grains red dot with a 200 gr. swc. It is not extremely clean burning but it is easy to verify that there is the correct amount of powder in the case, since it fills up the case better than bullseye. In addition to better load density, on a progressive machine I like to visually check the powder level before seating the bullet.  Red dot also makes for good light loads in 12 gauge and for cast rifle bullet loads.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: vooduchikn on September 12, 2011, 09:36:10 AM
I load 5.0 grains red dot with a 200 gr. swc. It is not extremely clean burning but it is easy to verify that there is the correct amount of powder in the case, since it fills up the case better than bullseye. In addition to better load density, on a progressive machine I like to visually check the powder level before seating the bullet.  Red dot also makes for good light loads in 12 gauge and for cast rifle bullet loads.

I am currently using Winchester WST. It shoots well and seems to burn pretty clean. It also meters well in my 650.  I shot a lot of it at the last HDF shoot and had no issues with it. The load data is on my other computer.

I run a Dillon 650 and like you,  look down the cases (most times) to get an idea that the charge is right. Can't see in there when loading .223/5.56.  I have tried to figure out how to double charge a case, but do not see how it is possible on my 650 UNLESS you intentionally try to do it.

Nice to see another reloader on the board.

WELCOME!
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on June 07, 2012, 10:14:50 AM
Better late than never...You must have been a shotgunner with lots of leftover WST. It is a useful powder for 45acp. In a 4' commander you are on the right track with 4.7 WST and a 230FMJ head. I would increase the taper crimp a bit, maybe 0.466 at the mouth. You should chrono that load if you are going to shoot mppl with that.
Failure to feed a ball ammo could be the crimp or perhaps an extractor adjustment. You could go up to around 5.0 gr.WST if necessary.

Tested these out today on the range. No failures to fire or over charged loads. I have a few (4)  fail to feeds in my Colt Commander. My buddy had zero issues in his full size colt. I attribute this to the fact that my recoil spring is stiffer than his.

The loads felt very light as compared to Speer Law Man factory ammo. The difference was very noticeable. I had no issues with shooting the Speer through my Commander. The OAL on our reloads as compared to the factory was almost the same with a slight variation amongst the group. I think this is due to using mixed headstamp brass.

Came home and reloaded another batch of 200, and upped the charge from 4.2 to 4.7gns of Winchester WST.   Will be out there next weekend to run this batch through our Colts and see how they shoot.

The WST shot very cleanly. There was no unburnt powder in the cases. All the guys i talked that reload have said to use "Bullseye" powder. Anyone on here have experience with this brand?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: clshade on June 07, 2012, 10:40:23 AM
5.5 grains Universal with 230 LRN. Lee tumble lube mold (ebay WW lead) using Rooster Jacket. Needs a medium-ish crimp to keep the bullets from shifting in their cases during fire. CCI LP primers because they are sooooo much easier to load into the priming tool.

Works great for me. Cheap as can be and accurate enough in the 5" XD.

I originally settled on Universal because I was looking for a Hodgdon powder (which is about all I can get easily here) that I could also use for a 44 mag carbine and eventually shotgun loads. The 44 idea didn't work out as well as I'd have liked but this load works really well in the stock XD. Much less and it will occasionally fail to cycle, too much more and its a +P load. The gun can handle it but accuracy suffers and there's no reason to beat up the gun that way. 
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on November 24, 2012, 06:07:15 AM
I had too much time on my hands so I decided to create this diagram for 45 shooters who reload their own ammo.
While browsing other forums on the mainland, I noticed a surprising amount of poor quality reloading advice.
The dimensions shown are actually a compromise of functional reliability and accuracy. So the average shooter will find it useful.
As far as powder selection goes, I've tried many and documented actual velocity measurements from my personal firearms.
However I have not tried any of the relatively new powders on the market. I have too much old stock I need to burn.
For this caliber, I favor WW231 or HP38. I have had good results with Bullseye, Trap100 (obsolete), and Clays.
Unique is also useful for special purpose ammo. I can supply specific results if you have a specific request.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on November 24, 2012, 07:53:51 AM
I had too much time on my hands so I decided to create this diagram for 45 shooters who reload their own ammo.
While browsing other forums on the mainland, I noticed a surprising amount of poor quality reloading advice.
The dimensions shown are actually a compromise of functional reliability and accuracy. So the average shooter will find it useful.
As far as powder selection goes, I've tried many and documented actual velocity measurements from my personal firearms.
However I have not tried any of the relatively new powders on the market. I have too much old stock I need to burn.
For this caliber, I favor WW231 or HP38. I have had good results with Bullseye, Trap100 (obsolete), and Clays.
Unique is also useful for special purpose ammo. I can supply specific results if you have a specific request.

Thanks for the pic.  It is perfect!

 Haha, it took me a lot of experimentation to come up with what you have illustrated, and others can benefit greatly from what you posted, and not waste so many rounds trying to figure it out.   :thumbsup:
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: ren on November 24, 2012, 04:16:32 PM
I had too much time on my hands so I decided to create this diagram for 45 shooters who reload their own ammo.
While browsing other forums on the mainland, I noticed a surprising amount of poor quality reloading advice.
The dimensions shown are actually a compromise of functional reliability and accuracy. So the average shooter will find it useful.
As far as powder selection goes, I've tried many and documented actual velocity measurements from my personal firearms.
However I have not tried any of the relatively new powders on the market. I have too much old stock I need to burn.
For this caliber, I favor WW231 or HP38. I have had good results with Bullseye, Trap100 (obsolete), and Clays.
Unique is also useful for special purpose ammo. I can supply specific results if you have a specific request.
Thanks for the reference.
I shoot bullseye pistol and just chono'd my match loads of 4.4 bullseye with a 230 FMJ on top. Only getting about 750 fps. Would bumping up to 4.6 grains help it get up to speed?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on November 24, 2012, 06:43:22 PM
Thanks for the reference.
I shoot bullseye pistol and just chono'd my match loads of 4.4 bullseye with a 230 FMJ on top. Only getting about 750 fps. Would bumping up to 4.6 grains help it get up to speed?
=======
As I recall, match grade mil. ball spec was 780. Service grade ball is something like 830. So 4.6 sounds about right if 780 is yur goal. I never actually chronographed that particular load tho...
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Teichi on November 24, 2012, 06:52:33 PM
From http://www.bullseyepistol.com/reloads.htm (http://www.bullseyepistol.com/reloads.htm)

A True Hardball Load for .45 Service Pistol

The following represents recipies to duplicate a true .45 caliber hardball load.

The NRA has published some load info that should fill your needs.

American Rifleman June 1993, pgs. 44-45
Loads to simulate Hardball recoil and energy 850 +/- 30 FPS vel

200-220 WC lead (such as Lyman 452460) OAL 1.16"
4.6-5.0 gr BE, Red or Green Dot, 700X
6.0-6.5 gr Unique
5.5-6.0 gr WW231
The above loads can also be used with a 230 gr FMJ bullet to get 850 FPS
+/- 30 with overall length of 1.25"


Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on November 24, 2012, 08:43:46 PM
From http://www.bullseyepistol.com/reloads.htm (http://www.bullseyepistol.com/reloads.htm)

A True Hardball Load for .45 Service Pistol

The following represents recipies to duplicate a true .45 caliber hardball load.

The NRA has published some load info that should fill your needs.

American Rifleman June 1993, pgs. 44-45
Loads to simulate Hardball recoil and energy 850 +/- 30 FPS vel

200-220 WC lead (such as Lyman 452460) OAL 1.16"
4.6-5.0 gr BE, Red or Green Dot, 700X
6.0-6.5 gr Unique
5.5-6.0 gr WW231
The above loads can also be used with a 230 gr FMJ bullet to get 850 FPS
+/- 30 with overall length of 1.25"
=============
Teichi-These are all good numbers that I have used in the past. I just shot some 5.6-231 with 230fmj yesterday. That load is in between match ball and service ball.
Remember match ball ammo in a white box?
I have an NRA publication on the 45 auto that is very helpful. It should be a part of every 1911 shooter's bookshelf.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Teichi on November 24, 2012, 10:21:03 PM
I used up all of my Bullseye, and W231 on 9mm. I working on using up my Universal on 9mm. I'm tapping into a 12lb keg of 700X for 45ACP 230gr Hardball loads at 4.5gr a shot and 4.0gr for 115gr 9mm. I figure it should last me another 6years or so
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on November 25, 2012, 12:19:25 AM
=======
As I recall, match grade mil. ball spec was 780. Service grade ball is something like 830. So 4.6 sounds about right if 780 is yur goal. I never actually chronographed that particular load tho...
======================
Many apologies for the previous post. ---780fps was my velocity for my 230gr. IPSC major caliber match ammo. (fyi-it is lower now)
My memory failed me.
I just got home from work and looked at my stash of ammo and this is what I found.
For match ball ammo it should be 820. So 4.8 BE or 5.8-231 with a 230 gr. fmj would be approximating match ball ammo.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on November 25, 2012, 05:13:28 AM
I used up all of my Bullseye, and W231 on 9mm. I working on using up my Universal on 9mm. I'm tapping into a 12lb keg of 700X for 45ACP 230gr Hardball loads at 4.5gr a shot and 4.0gr for 115gr 9mm. I figure it should last me another 6years or so
==============
700x is great. I used to load 12 ga. with that. Then since I had a big can of that, I used it for 38's and 44 mag light target loads. I also used it for 45's with great success.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Aiea78 on January 31, 2013, 10:22:34 PM
I had too much time on my hands so I decided to create this diagram for 45 shooters who reload their own ammo.
While browsing other forums on the mainland, I noticed a surprising amount of poor quality reloading advice.
The dimensions shown are actually a compromise of functional reliability and accuracy. So the average shooter will find it useful.
As far as powder selection goes, I've tried many and documented actual velocity measurements from my personal firearms.
However I have not tried any of the relatively new powders on the market. I have too much old stock I need to burn.
For this caliber, I favor WW231 or HP38. I have had good results with Bullseye, Trap100 (obsolete), and Clays.
Unique is also useful for special purpose ammo. I can supply specific results if you have a specific request.

Sweet.  My new desktop background :D
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Sixdirty6 on March 10, 2013, 03:20:35 PM
I had too much time on my hands so I decided to create this diagram for 45 shooters who reload their own ammo.
While browsing other forums on the mainland, I noticed a surprising amount of poor quality reloading advice.
The dimensions shown are actually a compromise of functional reliability and accuracy. So the average shooter will find it useful.
As far as powder selection goes, I've tried many and documented actual velocity measurements from my personal firearms.
However I have not tried any of the relatively new powders on the market. I have too much old stock I need to burn.
For this caliber, I favor WW231 or HP38. I have had good results with Bullseye, Trap100 (obsolete), and Clays.
Unique is also useful for special purpose ammo. I can supply specific results if you have a specific request.

Got any recipes for Montana Gold 230gr JHPs over bullseye powder?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 25, 2017, 07:54:02 AM
I think it is time to resurrect this thread.
It has been 4 years and some things have changed, like the new gen coated and plated bullets and some new powders came out over the past few years.
Anybody got some new info to share?

Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 25, 2017, 12:28:44 PM
I just started reloading for .45 Auto Rim using 250gr LSWC (Only boolits I have in .45) for my Model 25.  I use CFE Pistol, Titegroup, Trail Boss and IMR Target (New Powder). Does anyone have any pet loads for .45 ACP using 250gr lead boolits using any powder?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 25, 2017, 01:23:53 PM
I just started reloading for .45 Auto Rim using 250gr LSWC (Only boolits I have in .45) for my Model 25.  I use CFE Pistol, Titegroup, Trail Boss and IMR Target (New Powder). Does anyone have any pet loads for .45 ACP using 250gr lead boolits using any powder?
....
I've tried 250 gr. Jhp in an acp before. I used AA5 powdeŕ.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 25, 2017, 01:31:20 PM
I also tried 250 gr lead flat pt but I can't find the data.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: mikenkapolei on August 25, 2017, 01:50:50 PM
I use 200gn powder coated SWC from Missouri Bullets, Starline brass and 4.8gr of HP38 or W231. Super accurate load in all of my guns.


Sent from my iPhone using Tapatalk
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 26, 2017, 05:11:02 AM
I also tried 250 gr lead flat pt but I can't find the data.
If you run across the data, would you let me know?

Thanks OF  :thumbsup: :thumbsup: :thumbsup:
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 26, 2017, 05:14:52 AM
I use 200gn powder coated SWC from Missouri Bullets, Starline brass and 4.8gr of HP38 or W231. Super accurate load in all of my guns.


Sent from my iPhone using Tapatalk
HP38 is another one of those powders I have been trying to find a good excuse to try. This is the excuse I need to go buy some. Thanks!  :thumbsup: :thumbsup: :thumbsup:
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 30, 2017, 07:09:37 AM
I was shooting my S&W Model 25 in 45 ACP this last Sunday. I have a very nice load for it using the 250gr LSWC that I buy locally along with 4.5gr of the IMR Target powder. I recently purchased some IMR Target powder and tried it for the first time. I shot 50 rounds of this load through my revolver and I have to say it is a pleasant load to shoot. And it hits at point of aim. The IMR Target powder is supposed to be IMR's competition to Bullseye. And I have to say in my revolver it works quite nicely.

I would like to see how it does in a semi. I don't own a semi in .45 ACP. If someone (OF?) would like to try some of this new powder in your 1911 or other semi I am more than happy to donate some of this new powder to the cause.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 30, 2017, 07:26:04 AM
I looked at the data for imr  target and it looks similar to 231/hp38, which I have been using for more than 30 years.
If you want to trade a half lb of hp38 for a half lb of target, I would do that and run a quick review.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 30, 2017, 07:31:50 AM
I looked at the data for imr  target and it looks similar to 231/hp38, which I have been using for more than 30 years.
If you want to trade a half lb of hp38 for a half lb of target, I would do that and run a quick review.
That sounds good! I am taking all next week off between jobs. So sometime next week would be a good time. And I will probably go to the range next Thursday 9/7. LMK if some time next week works for you.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 30, 2017, 07:43:19 AM
That sounds good! I am taking all next week off between jobs. So sometime next week would be a good time. And I will probably go to the range next Thursday 9/7. LMK if some time next week works for you.
...
I'm in town every afternoon and I'll  probably go shoot on Monday.
If we do the swap soon, I can test on Monday. Holidays are ideal for setting up the chrono.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 30, 2017, 07:54:46 AM
...
I'm in town every afternoon and I'll  probably go shoot on Monday.
If we do the swap soon, I can test on Monday. Holidays are ideal for setting up the chrono.
I'm at Ala Moana until 3pm. And I think I drive near your workplace on my way home if my memory is correct. Will that work for you? Obviously I don't have it with me today but I can bring it with me tomorrow. Friday is going to be a bad day for me to stop by because I am going to have my truck loaded with computer equipment and office stuff. But if I don't have to leave my vehicle I can stop by on Friday.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: stangzilla on August 30, 2017, 08:55:53 AM
I haven't done much reloading for 45acp yet.  so far I've only used Titegroup

4.8 grains of titegroup
hornady 230 grain FMJ
CCI 300 primer

reloading data I found for titegroup and 230 grain 45acp was around 3.8-6.4 grains
4.0 grains of titegroup did not cycle well at all in my 1911's, 4.8 grains did cycle very well.  and I can probably add a little more powder next time.
accuracy I'm not too sure exactly yet.
I don't have a chrono, so idk what the velocity is.  but the 4.8 grains of titegroup does feel slightly slower than a factory load of 230 grain FMJ.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 30, 2017, 09:49:05 AM
I'm at Ala Moana until 3pm. And I think I drive near your workplace on my way home if my memory is correct. Will that work for you? Obviously I don't have it with me today but I can bring it with me tomorrow. Friday is going to be a bad day for me to stop by because I am going to have my truck loaded with computer equipment and office stuff. But if I don't have to leave my vehicle I can stop by on Friday.
================
Tomorrow is ok. A little busy but I can manage. Here is a picture of me carefully weighing out a half a pound for you. LOL
I'll send you a pm telling you the best way to stop for the pick up.
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Inspector on August 30, 2017, 10:12:23 AM
================
Tomorrow is ok. A little busy but I can manage. Here is a picture of me carefully weighing out a half a pound for you. LOL
I'll send you a pm telling you the best way to stop for the pick up.
Is that your finger I see on the scale?  :rofl: :rofl: :rofl:
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on August 30, 2017, 10:21:19 AM
Is that your finger I see on the scale?  :rofl: :rofl: :rofl:
====
dammit, gotta learn how to use photoshop
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Vbc on January 23, 2018, 06:14:11 AM
Square deal...bullseye 3.8 gr...200 gr swc...starline brass...45acp 5”...25 yds
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on January 23, 2018, 06:37:19 AM
nice shootin'

is that 1 hand or 2 hand?
bench or unsupported?
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: Heavies on January 23, 2018, 08:33:41 AM
Square deal...bullseye 3.8 gr...200 gr swc...starline brass...45acp 5”...25 yds
This. The tried and true bullseye load, can't go wrong with That! 👍
Title: Re: .45 ACP LOAD - "RECIPES"
Post by: oldfart on January 23, 2018, 08:38:10 AM
This. The tried and true bullseye load, can't go wrong with That! 👍
...
As they say....garans ballbearins