2aHawaii

General Topics => General Discussion => Topic started by: kekoa on April 10, 2014, 10:25:33 AM

Title: AR lower question
Post by: kekoa on April 10, 2014, 10:25:33 AM
Is a forged aluminum or a polymer lower better for an AR build? Any pro/con would be helpful. Thanks
Title: Re: AR lower question
Post by: SpeedTek on April 10, 2014, 11:43:22 AM
Depends what you building.  Polymer is great for hunting and/or building a light gun. I have a precision AR using the New Frontier Poly lower because the upper and lower has no playback I have a 2 stage trigger in that lower.  My personal ARs I have 5 poly lowers and 3 aluminum lowers.  for me personally I like the NFA poly lowers since they are stiffer than the other poly lowers. 
Title: Re: AR lower question
Post by: WCMTWS on April 11, 2014, 01:54:31 AM
Shouldn't even be a question
Title: Re: AR lower question
Post by: kekoa on April 11, 2014, 05:03:02 AM
Shouldn't even be a question

Helpful
Title: Re: AR lower question
Post by: Surf on April 11, 2014, 05:58:20 AM
Forged hands down.  Can certain uses get away with a poly lower?  Yes they can, but forged is still superior. 
Title: Re: AR lower question
Post by: 2aHawaii on April 11, 2014, 06:43:08 AM
Forged hands down.  Can certain uses get away with a poly lower?  Yes they can, but forged is still superior. 

+1
Title: Re: AR lower question
Post by: ren on April 11, 2014, 07:22:50 AM
Forged.
The problem with plastic lowers is that they follow the same design as a forged lower and that is a point of failure. There's a pic at the range that shows this. The only other plastic lower that is a total redesign is the CavArms lower.
Title: Re: AR lower question
Post by: macsak on April 11, 2014, 07:32:30 AM
Forged.
The problem with plastic lowers is that they follow the same design as a forged lower and that is a point of failure. There's a pic at the range that shows this. The only other plastic lower that is a total redesign is the CavArms lower.

only cavarms is redesigned?
or are there others that are not copies?
Title: Re: AR lower question
Post by: ren on April 11, 2014, 08:37:32 AM
only cavarms is redesigned?
or are there others that are not copies?
Perhaps there are as I dont track plastic lowers - for I have no desire to own one.
The design Im referring to is one where it incorporates the stock into the lower. The way Frontier and Plum Crazy designed their lower was the same as if they were making it out of aluminum. When I sling up, Id probably crack a plastic lower. Sure I got an offer to replace it if it cracks but why should I buy one under the pretense of a warranty Ill certainly use? Replacing a plastic lower will get old. Not only the repair but reregistering the new plastic lower with HPD. No thanks. All you fanboys can cry me a river but lets face it an aluminum lower is proven and its current price is affordable. A plastic lower should suffice for a.range queen and fondling in a wet dream of a zombie apocalypse or TEOTWAWKI.
Title: Re: AR lower question
Post by: aieahound on April 11, 2014, 11:56:30 AM
My opinion,
If you're building your 3rd or 4th AR, polymer is fine. Triggers are great.

If you're buidling your first or only AR, got to go forged aluminum, or billet aluminum if you want to get fancy ( and expensive).
Title: Re: AR lower question
Post by: kia_killer on April 11, 2014, 12:31:30 PM
Depends on your plans for the gun. Is weight and price a factor?  Does chatter from unmatched uppers/lowers bother you? Do you want a gun you can bash in zombie skulls with walking dead style? If price and weight don't matter, go aluminum. If your planning on going into battle with it, go aluminum. For the recreational shooter and hunter, a polymer lower will hold up just fine.
Title: Re: AR lower question
Post by: kekoa on April 11, 2014, 01:54:30 PM
I went with a forged aluminum lower from ar15part.com. Got a complete upper coming too from gunbroker.com. I chickened out on the full build out this time, I really want to give it try on the next one...think I will just slowly get parts under the radar (if you know what I mean) and poof there is a new gun and my wife will almost have no clue. Crafty huh.
Title: Re: AR lower question
Post by: sliver on April 11, 2014, 04:24:10 PM
for those with an ar which does not fit exactly together, why not just buy an Accurizing Wedge like this one http://www.midwayusa.com/product/518277/utg-accurizing-wedge-ar-15 (http://www.midwayusa.com/product/518277/utg-accurizing-wedge-ar-15)

they are cheap and work well.

as for polymer lowers, has anyone actually seen one fail, it seems like I have heard of 2 or 3 which have on the internet and that's out of how many thousands which have been made/sold/used.  It seems like most come with life time warranties and locally I have yet to see one fail in real life. 

Either way, I'd buy one of each.  They are cheap (usually about 80-100 bucks a piece locally, up to 300 if you wanna get fancy and expensive.  I've seen it for 50 bucks on sale at palmetto state armory but you gotta ship it in to a ffl and its gonna be another 50 by the time your done with that.) and the polymers seem good if weight is the main issue.  If it polymers craps out, just rip the guts out of it and throw it in to the aluminum/metal lower.  I'm surprised no one has mentioned the magnesium lowers as far as weight is concerned although I know some people have concerns about the strength of those as well. 

 


Title: Re: AR lower question
Post by: sliver on April 11, 2014, 04:25:45 PM
Got a complete upper coming too from gunbroker.com.

what upper did you go with? 
Title: Re: AR lower question
Post by: kekoa on April 11, 2014, 04:48:42 PM
what upper did you go with?


    
 AR-15 Upper 5.56 Matrix Mil-Spec Upper, Stoner BCG, Mil-Spec charging handle, 16” Colt Socom 1-8 Twist barrel, 10” T-Mark hand rail with end cap, YHM Gas block & tube Also came with a nickel boron BCG.
Title: Re: AR lower question
Post by: ren on April 11, 2014, 05:54:13 PM
for those with an ar which does not fit exactly together, why not just buy an Accurizing Wedge like this one http://www.midwayusa.com/product/518277/utg-accurizing-wedge-ar-15 (http://www.midwayusa.com/product/518277/utg-accurizing-wedge-ar-15)

The fit of the upper and lower does not affect accuracy - has been proven many times by many experienced shooters. Ask the AMU
Title: Re: AR lower question
Post by: sliver on April 11, 2014, 06:48:03 PM
The fit of the upper and lower does not affect accuracy - has been proven many times by many experienced shooters. Ask the AMU


oh yeah I know that, it does get rid of the rattle some people don't like though which is what I though we were talking about. 
Title: Re: AR lower question
Post by: SpeedTek on April 11, 2014, 07:55:01 PM
You can drill and tap for another locking screw that puts pressure on the rear boss of the upper. But it takes longer to take apart.  They also make wedge pins for the front and rear takedown pins but again you need a Allen or screw driver to loosen it and remove the pins.  Accu wedge is not perfect but it helps. I have also stipples the upper recv and that works but doesnt last.
Title: Re: AR lower question
Post by: WCMTWS on April 11, 2014, 08:29:00 PM
Helpful

You're welcome, just ring if you need more help.
Title: Re: AR lower question
Post by: Colt808 on April 11, 2014, 09:04:42 PM
I try to be very supportive of anyone who wants to build their own AR, so in the end I'll end up saying: buy what you want and can afford.  That said, the others raise some valid concerns that you should keep in mind.  Personally, I believe if it is something a life might depend on...the only choice is a forged lower.  I'm sure there are those who will argue "people said the same about Glock, blah, blah, blah..."; well when Glock makes a polymer lower I'll consider it.  Until then, I'll spend few dollars more and deal with the few extra ounces of a forged receiver.

Redesigned or not, it's stuff like this that would always be on my mind...
(http://i612.photobucket.com/albums/tt203/Colt808/2aHI/Share/e8b14664-7746-4644-b38f-1c3f6a33e7cd.jpg)

(http://i612.photobucket.com/albums/tt203/Colt808/2aHI/Share/b852dea6-9176-4ce4-bfed-6326fed3452c.jpg)
Title: Re: AR lower question
Post by: SpeedTek on April 12, 2014, 01:33:07 AM
Sh*t happens.

Plum Crazy polymer was softer than the current NFA Lowers

Gee I wonder why they show the buffer nut wrench in the picture.....


Title: Re: AR lower question
Post by: kekoa on April 12, 2014, 04:24:45 AM
You're welcome, just ring if you need more help.

Nah, think I will pass. Need useful help.
Title: Re: AR lower question
Post by: ren on April 12, 2014, 07:45:16 AM
Nah, think I will pass. Need useful help.

 :-\
Title: Re: AR lower question
Post by: kekoa on April 12, 2014, 12:30:07 PM
:-\

I appreciate all of your help, this guy was being no so helpful in my opinion OK, frankly rude and arrogant. I am learning I am sorry I want to gain knowledge that type of arrogance just pushes away those you want to gain and keep to stand for on rights.

Title: Re: AR lower question
Post by: WCMTWS on April 12, 2014, 03:22:05 PM
I appreciate all of your help, this guy was being no so helpful in my opinion OK, frankly rude and arrogant. I am learning I am sorry I want to gain knowledge that type of arrogance just pushes away those you want to gain and keep to stand for on rights.

I was rude an arrogant? Because I said "It shouldn't even be a question" ... :rofl:
You might be new to this whole internet thing and if so I apologize but you should not get butt hurt over what people say on a discussion forum.


And I still stand by my initial comment.
Title: Re: AR lower question
Post by: ren on April 12, 2014, 05:17:09 PM
this thread went downhill
On one side you have people who really shoot and on the other people who just collect and sell guns.
Title: Re: AR lower question
Post by: Kanakamaoli23 on April 12, 2014, 06:52:37 PM
 :rofl: :popcorn:
Title: Re: AR lower question
Post by: dogman on April 12, 2014, 09:30:25 PM
 :stopjack:
Title: Re: AR lower question
Post by: SpeedTek on April 13, 2014, 01:29:47 AM
The fit of the upper and lower does not affect accuracy - has been proven many times by many experienced shooters. Ask the AMU

Not True. True

I have done extensive testing and my results differ
Title: Re: AR lower question
Post by: kekoa on April 13, 2014, 04:02:11 AM
Not impressed.

Fine by me I am not out here to impress and try to recover short comings as you need too. No question is a bad question when you want to learn. Your just an elites asshole. By the way....still fuck you dick head.
Title: Re: AR lower question
Post by: kekoa on April 13, 2014, 04:12:55 AM
Not True. True

I have done extensive testing and my results differ

Should I consider the accurizing wedge then if there is chatter between my lower and upper? I have not fit them yet bit will check on that when I get them. I did some reading, some say it was difficult if not impossible to get a good fit when using it (couldn't close action) Tips?
Title: Re: AR lower question
Post by: SpeedTek on April 13, 2014, 06:58:03 AM
You have to trim it if too tight. You kinda have to have a feel for it. Hard to explain.
Title: Re: AR lower question
Post by: ren on April 13, 2014, 08:57:37 AM
Not True. True

I have done extensive testing and my results differ

what was your methodology?
Title: Re: AR lower question
Post by: ren on April 13, 2014, 12:01:25 PM
one reason this forum sucks
you got some peeps trying to make money and they're so full of shit that it ain't even funny...
(http://2.bp.blogspot.com/-zXC2HKZkfCI/UFxNpk68b1I/AAAAAAAAEOI/PCcY_LFsRb8/s1600/bs1.jpg)
Title: Re: AR lower question
Post by: SpeedTek on April 13, 2014, 01:33:26 PM
Where did this thread go wrong?

Unless I am missed something...Where did it resort to name calling?

Take a step back guys and cool down.  Lets be gentlemen here.

We all have our own preferences.  We make our own choices.  Buy what we want, use what we want.

Title: Re: AR lower question
Post by: BUD on April 13, 2014, 01:43:34 PM
:rofl: :popcorn:

 :popcorn: :popcorn: :popcorn:
Title: Re: AR lower question
Post by: SpeedTek on April 13, 2014, 01:45:30 PM
I have enough Drama in my life........2Adrama! LOL
Title: Re: AR lower question
Post by: ren on April 13, 2014, 01:56:40 PM
:popcorn: :popcorn: :popcorn:
:popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn: :popcorn:
Beat Street 1984 HD (The Roxy Battle) 720p (http://www.youtube.com/watch?v=c_ShwO10d6g#ws)


RIP Buck4 Kuriaki  :(
Title: Re: AR lower question
Post by: ren on April 13, 2014, 04:27:59 PM
(http://masonologyblog.files.wordpress.com/2014/03/welcome_to_the_internet__please_follow_me_by_sharpwriter-d5buwfu.jpg)
Title: .
Post by: Q on April 13, 2014, 08:51:12 PM
.
Title: Re: AR lower question
Post by: sliver on April 13, 2014, 09:54:47 PM
Should I consider the accurizing wedge then if there is chatter between my lower and upper? I have not fit them yet bit will check on that when I get them. I did some reading, some say it was difficult if not impossible to get a good fit when using it (couldn't close action) Tips?

you may need to trim/sand it down but it really shouldn't be too hard.  I'd suggest putting your rifle together and seeing if it even needs the wedge.  Some people don't give a crap about a slight rattle or may not even notice it.  If you do, stick it in and slowly shave it down until you get the fit you want.  It's all trial and error and it is pretty easy to do, buy a few (they are cheap) just in case you screw up the first one although if you go slowly, I doubt you will have very much of a problem. 
Title: Re: AR lower question
Post by: sliver on April 13, 2014, 09:58:41 PM
Redesigned or not, it's stuff like this that would always be on my mind...
(http://i612.photobucket.com/albums/tt203/Colt808/2aHI/Share/e8b14664-7746-4644-b38f-1c3f6a33e7cd.jpg)

(http://i612.photobucket.com/albums/tt203/Colt808/2aHI/Share/b852dea6-9176-4ce4-bfed-6326fed3452c.jpg)

yes but I'm sure we have all seen these pictures before and again, these are 2 out of how many thousands of polymer lowers made and used and who is to say a these failures are not due to bad ammo.  Doesn't really matter as the OP has already bought his lower already but I've seen even forged lowers have problems/cracks...  As for glock making lowers, I've seen quite a bit of glocks blow up as well but usually its due to ammo and not the polymer guns being the problem.
Title: Re: AR lower question
Post by: ren on April 14, 2014, 06:33:19 PM
http://www.armalite.com/images/Tech%20Notes%5CTech%20Note%2055,%20Receiver%20Tightness.pdf (http://www.armalite.com/images/Tech%20Notes%5CTech%20Note%2055,%20Receiver%20Tightness.pdf)

enough said
Title: Re: AR lower question
Post by: sliver on April 14, 2014, 07:42:34 PM
http://www.armalite.com/images/Tech%20Notes%5CTech%20Note%2055,%20Receiver%20Tightness.pdf (http://www.armalite.com/images/Tech%20Notes%5CTech%20Note%2055,%20Receiver%20Tightness.pdf)

enough said



yes and no, yes in that I personally do not believe looseness affects accuracy as the relationship between the scope and barrel has nothing to do with the fitment between the upper and lower receiver and that the bullet would exit long before it had an effect on the upper movement and the lowers but no in that the article you submitted is not a double blinded study with any type of peer review so it is basically worthless as if I were to have written it.  Does not matter if it came from a reputable company, it holds no water with any scientific community. 

Either way, I find one of the easiest ways to remove rattle for more confidence in your weapon would be the little wedge.  They cost like 2-3 bucks and work to remove the rattle.
Title: Re: AR lower question
Post by: ren on April 14, 2014, 07:54:55 PM


yes and no, yes in that I personally do not believe looseness affects accuracy as the relationship between the scope and barrel has nothing to do with the fitment between the upper and lower receiver and that the bullet would exit long before it had an effect on the upper movement and the lowers but no in that the article you submitted is not a double blinded study with any type of peer review so it is basically worthless as if I were to have written it.  Does not matter if it came from a reputable company, it holds no water with any scientific community. 

Either way, I find one of the easiest ways to remove rattle for more confidence in your weapon would be the little wedge.  They cost like 2-3 bucks and work to remove the rattle.

I did not refer to this article as a peer reviewed article and I can't find the results from the Rodman Labs. We can argue on the forums to no avail.  The AMU is a well established unit that has very reputable armorers and shooters from all disciplines.
You're more than welcome to prove your point .
Title: Re: AR lower question
Post by: Teichi on April 14, 2014, 08:59:29 PM
I have not seen any measureable differences in fit and accuracy for ARs. Confidence is a major factor in winning matches. If a tight fit or a rubber wedge helps with building that confidence, then go for it. I have been in "as issued" service rifle matches that listed such wedges as illegal for these competitions. The top 5 shooters from each relay had to have their rifles inspected for modification at the completion of the course of fire. On a side note,  "Light enhancing"  glasses (amber or vermillion) were also on the banned list for these matches.

The bottom line is that you should do it if it makes a difference to you.