2aHawaii
General Topics => Off Topic => Topic started by: wirecounter on August 05, 2014, 07:41:23 AM
-
I have some old (15 years old) awning windows (aluminum frame) that I need some welding work done. All of my window hardware on the mauka side of the house has corroded to the point that the windows will not operate.
The work I need done: The "arms" on both sides of each window have corroded off of the bar that connects the hardware on both sides of the window that open it. I need to have the "arms" welded back on to the bar. I plan to clean off all of the corrosion build up down to bare metal so it can be welded and hold.
Please let me know if you know anyone who can perform this work.
On a side note, the manufacturer of the awning windows went out of business years ago as well as the window contractor that originally installed them = parts are obsolete. BUT, I found a window hardware supplier on the internet, Blaine Window Hardware, Inc. - www.blainewindow.com (http://www.blainewindow.com) that has awning window operators (part number 00095-L-037) that can replace my corroded operators, with some modifications. I know that I am not the only one who has these windows (I went to a window contractor that smugly told me that hundreds of people in Hawaii have the same problem/window that I do so just spend the $$$ and buy the replacement from us. Very helpful) so PM me for the details. I refuse to spend upwards of 5k per window, especially when I have 8 windows that would need replacement, when some $25 part, some ingenuity, and professional welding (I gave up on alumaloy) can fix the problem. These windows have been a thorn in my side for a few years and I am relieved to have a solution that will not cost me 40k! :thumbsup:
-
How about some photos.
-
How about some photos.
-
Is the "bar" that the arms are going to be welded to removable, or does the welding need to happen in the frame?
-
Im not sure that would be salvageable. Aluminum has to be very clean to weld good.
-
does that part pivot?
-
Is the "bar" that the arms are going to be welded to removable, or does the welding need to happen in the frame?
The bar is not removable as it is sandwiched within the frame. It is on the bottom of the frame and it pivots within a plastic sleeve on each side that allows it to pivot in the frame. I can clean it up with my dremel tool as I cleaned one up with the wire wheel and cutter attachments, but the base metal did not get hot enough for the alumaloy to adhere to it (should have known better than to believe infomercials).
-
The bar is not removable as it is sandwiched within the frame. It is on the bottom of the frame and it pivots within a plastic sleeve on each side that allows it to pivot in the frame. I can clean it up with my dremel tool as I cleaned one up with the wire wheel and cutter attachments, but the base metal did not get hot enough for the alumaloy to adhere to it (should have known better than to believe infomercials).
I think trying to weld it in place will damage the plastic bushing. Is there any room to make an external pivot point? Maybe you can bypass the portion inside the frame, screwing a bracket/pivot point on the top of the frame. May have to modify the window some?
-
It may be a little tough to weld after cleaning it up. Maybe some aluminum flat bar and some rivets to remake the bottom half of the bracket,and find a way to remount on the outside of the frame.
-
its gonna be hard to weld that looking at the picture it looks very oxidized and the aluminum looks like cast both not in your favor. with cast alloy it needs to be very clean and preheated to have a good penetrating weld. if the part that you need welding isn't able to be removed and there is a plastic bushing that's not removable it its very likely to get destroyed when preheating the aluminum. also is there enough room to weld the opposite side of the arm cant really tell in the picture.
-
Are they all like the one posted or are any of them in good shape? If you could post pictures of one in better shape and in different positions it might help.
-
Are they all like the one posted or are any of them in good shape? If you could post pictures of one in better shape and in different positions it might help.
Attached is a downward looking view of a good "arm." Plastic bushing on top screwed/secured to the window frame.
-
Mahalo guys for your input/suggestions.
I would like to be able to close the window fully which make modifying the hardware virtually impossible as the rotating bar sit directly under the window pane when window is fully closed. Not sure if both arms need to be fully secured to the rotating bar, but it would be best so it doesn't get tweaked.
Maybe a better solution is to get a retrofit kit that would fit within the opening without having to rip out the framing?
Gotta leave for a meeting so I will post more pics when I get back home this afternoon.
:shaka:
-
Long shot but try checking reuse hawaii.Ive been able to find a few discontinued jealousies parts for my house there
-
Long shot but try checking reuse hawaii.Ive been able to find a few discontinued jealousies parts for my house there
Thanks for the suggestion, but the parts I need welded together cannot be removed/replaced without removing the entire window frame from my house - not doable. :shaka:
-
Okay . . .
I uploaded videos of the not working window https://www.youtube.com/watch?v=JA8PXjTQYZE&feature=youtu.be (https://www.youtube.com/watch?v=JA8PXjTQYZE&feature=youtu.be)
and the working window https://www.youtube.com/watch?v=tbzkCg5XfWU&feature=youtu.be (https://www.youtube.com/watch?v=tbzkCg5XfWU&feature=youtu.be)
I hope these help. Please let me know if you have any additional questions. :shaka:
-
Attached is a downward looking view of a good "arm." Plastic bushing on top screwed/secured to the window frame.
What happens when you remove the phillips screws in the photo? It looks like the pivoting bar is being held in by those brackets holding the plastic bushings.
-
Consider contacting the manufacturer and purchasing a couple of replacement pieces. The part looks like it is riveted in which probably means that it can be drilled out and replaced
-
What happens when you remove the phillips screws in the photo? It looks like the pivoting bar is being held in by those brackets holding the plastic bushings.
Not really sure what purpose the philips screws serve. I actually removed the pivoting bar from one of my windows in the garage, but I had to pry it out of the window frame. In the process the bar got bent/bowed out of shape. The plastic bushings fit on the ends of the pivoting bar and into the frame and there is no slack between it and the "arms." Unfortunately, I mailed the removed assembly to a window company on the mainland and they never "received" it - should have sent it certified mail.
Maybe I should take another crack at it as I have 3 other windows in the garage that do not really need to be operational . . .
On another note, the replacement awning operators are almost a perfect fit for my windows with some modification on the mounting holes (read drill out). Only thing is that the bar that pivots on it is a 1/4" short = window will not open or close fully. Not sure how the hinge was installed, I need to drill it out to exchange the bar, but not sure how to re-attach it. Any ideas?
See photos of both sides of the operator hinge
-
Consider contacting the manufacturer and purchasing a couple of replacement pieces. The part looks like it is riveted in which probably means that it can be drilled out and replaced
Manufacturer and installer went out of business years ago. Not sure who it is/was either
-
The part looks like it is riveted in which probably means that it can be drilled out and replaced
Do you mean the arm is riveted to the bar?
-
Manufacturer and installer went out of business years ago. Not sure who it is/was either
You're right. Sorry, went back to reread your post and missed that part.
-
new HCC welding class session begins Aug. 28 for anyone interested!
-
new HCC welding class session begins Aug. 28 for anyone interested!
Thanks! I am seriously considering taking the class & take time off of work to do so.
-
Thanks! I am seriously considering taking the class & take time off of work to do so.
Carpe Diem (or night this is a non-credit night class at 6pm, the day credit class is booked solid already) :D
Intro to Arc - sign up now the class is wide open not filled up yet!
http://www.808trades.org/course/24/introduction-to-arc-welding.html (http://www.808trades.org/course/24/introduction-to-arc-welding.html)
http://www.808trades.org/register.html (http://www.808trades.org/register.html)
Introduction to Arc Welding, Arc Welding 2, Arc Welding 3, & Arc Welding 4:
- Leather Gloves
- Chipping Hammer
- Wire Brush
- Pliers
-
Manufacturer and installer went out of business years ago. Not sure who it is/was either
Have you tried contacting Screens & Things?? I had them replace my aluminum window frames about two years ago, I know you don't want to replace the frames but maybe they have some knowledge on the system and parts used in your installation.
-
Have you tried contacting Screens & Things?? I had them replace my aluminum window frames about two years ago, I know you don't want to replace the frames but maybe they have some knowledge on the system and parts used in your installation.
The window frame is sandwiched between the siding of my house and the drywall & 2x4 framing inside my house. I would need to bust open my interior walls to remove the aluminum window frames.
But, thanks for the suggestion as I recall that a friend of mine owns that company & I thought they only did window screens . . . :shaka: I will check it out if removing the bar without damaging it does not pan out.