2aHawaii
General Topics => General Discussion => Topic started by: Dregs on August 01, 2011, 05:57:54 PM
-
After much procrastination, I went to the silhouette side for the first time on Sunday. I declared I have never been to that side before, and one of the range officers showed me the ropes. I asked a bunch of questions to the guy in the booth too.
It's ridiculously far range for a pistol and I personally won't go back there with just pistols. 100 rounds have been shot between me and a friend, and I can't tell if any of my guns are shooting straight or not.
It was a friendly good experience.
-
If you're going to shoot pistols at the silhouette side then you can't aim for the little 3 inch targets. That will hurt your feelings.
Instead go for the "man sized" targets.
This is what I do with pistols.
My 10/22 however, loves to plink the little 2 inch bolts at 50 and 75 yards.
-
I guess my problem was I have no idea if I'm even hitting the damn thing. I was going for the man-sized targets. There is a slim and tall one on the left side. I didnt' go for the big ugly gong though, since that's more on the right side. lol.
-
It's easy to spot your misses - just watch the dirt around the targets. If you hear ringing steel, then you hit your target. If you don't hear bullets hitting steel and don't see dirt flying, then you have a really bad flinch and should work on keeping your eyes open and trigger control when you shoot.
-
I'm more of a rifles kind of guy, and I'm not well versed in handgun theory yet. Nor in working with steel silhouettes.
For example, what range is POA and POI the same? 7 yards? At 50 yards, do I aim high? How high? 6' o'clock hold? POA and POI can't be the same even at 50 yards....? Wait, can it? Is someone else aiming for the same one I'm hitting? Crap was that mine or not? Is there a noticeable time delay with flight time when I'm aiming that far with handguns? I could go for some shaved ice right now. I haven't heard a single pinging that might be mine yet. I think. Wait, maybe they were mine. I don't hear pings as much as people are taking shots, so others must be missing a lot too. Wonder if waiolas is crowded about now. Maybe my gun in particular isn't strong enough to make it ping when if I hit the target? Man is the round even hitting where I'm aiming? Or is it hitting somewhere under my gun where I can't see while aiming. Probably gonna get vanilla ice cream with vanilla syrup as usual. Or maybe the POI is way high, and I'm not even looking at the right area to track my shot. I see dirt getting kicked, but is that because that's where I was aiming, or it bounced off the metal target and is hitting the dirt? Wow there's a lot of dirt being kicked here. The dirt is nice and powdery though.
Yeh it's a personal problem of why I'm not taking my handguns there again. At least until I get more experience with handguns.
-
I'm more of a rifles kind of guy, and I'm not well versed in handgun theory yet. Nor in working with steel silhouettes.
For example, what range is POA and POI the same? 7 yards? At 50 yards, do I aim high? How high? 6' o'clock hold? POA and POI can't be the same even at 50 yards....? Wait, can it? Is someone else aiming for the same one I'm hitting? Crap was that mine or not? Is there a noticeable time delay with flight time when I'm aiming that far with handguns? I could go for some shaved ice right now. I haven't heard a single pinging that might be mine yet. I think. Wait, maybe they were mine. I don't hear pings as much as people are taking shots, so others must be missing a lot too. Wonder if waiolas is crowded about now. Maybe my gun in particular isn't strong enough to make it ping when if I hit the target? Man is the round even hitting where I'm aiming? Or is it hitting somewhere under my gun where I can't see while aiming. Probably gonna get vanilla ice cream with vanilla syrup as usual. Or maybe the POI is way high, and I'm not even looking at the right area to track my shot. I see dirt getting kicked, but is that because that's where I was aiming, or it bounced off the metal target and is hitting the dirt? Wow there's a lot of dirt being kicked here. The dirt is nice and powdery though.
Yeh it's a personal problem of why I'm not taking my handguns there again. At least until I get more experience with handguns.
I laughed good and hard at your mental narrative. Well played, sir.
-
I'm more of a rifles kind of guy, and I'm not well versed in handgun theory yet. Nor in working with steel silhouettes.
For example, what range is POA and POI the same? 7 yards? At 50 yards, do I aim high? How high? 6' o'clock hold? POA and POI can't be the same even at 50 yards....? Wait, can it? Is someone else aiming for the same one I'm hitting? Crap was that mine or not? Is there a noticeable time delay with flight time when I'm aiming that far with handguns? I could go for some shaved ice right now. I haven't heard a single pinging that might be mine yet. I think. Wait, maybe they were mine. I don't hear pings as much as people are taking shots, so others must be missing a lot too. Wonder if waiolas is crowded about now. Maybe my gun in particular isn't strong enough to make it ping when if I hit the target? Man is the round even hitting where I'm aiming? Or is it hitting somewhere under my gun where I can't see while aiming. Probably gonna get vanilla ice cream with vanilla syrup as usual. Or maybe the POI is way high, and I'm not even looking at the right area to track my shot. I see dirt getting kicked, but is that because that's where I was aiming, or it bounced off the metal target and is hitting the dirt? Wow there's a lot of dirt being kicked here. The dirt is nice and powdery though.
Yeh it's a personal problem of why I'm not taking my handguns there again. At least until I get more experience with handguns.
Dude, seriously, get out of my brain!
-
Let me know when you're going to the pistol range again.
I'll go with you.
I'm a half decent pistol shot. :thumbsup:
-
I'm the opposite of Dregs. I've only gone to the silhouette side and never gone to the other side, because I have been too lazy to make myself a frame. I experienced the same problems but so far have managed to find it useful training.
As KingKeoni said, the tiny targets are not for pistols, they will hurt your feelings. Go for the big giant target or the two man-sized targets. If you are good then you can go for the next smaller targets. I would be amazed to see any standing pistol shooter taking down the tiny targets.
It's not that easy to hear the ringing steel but you can usually hear it. The ringing will occur about 1/5 second after you fire depending what ammunition you shoot. Most bullets travel at roughly the speed of sound, and to hear the ring the sound must also bounce back to your ears so that doubles the time delay. Try not to fire when other people are firing, then you can know the ringing is yours more easily.
If you see dirt getting kicked, 99% of the time it is because you missed. If the bullet bounces off the steel it will not smash the ground hard enough to kick dirt. When you see dirt getting kicked you can also roughly tell where you missed. You should see the dirt puff about 1/10 second after you fire, assuming you missed.
I don't know at what range POI and POA are the same either. Everyone says it depends on the particular handgun and how it is sighted. I asked the same question here previously as well. I always get different answers depending who I ask so I don't know what to believe. But actually not knowing what distance your handgun is sighted for is almost irrelevant. Because at most you will be 2 inches off vertically if you are shooting at the "wrong" distance, because that is the vertical distance between your barrel and your sights on your gun. And a 2 inch target at a distance of 50 years is miniscule. But it matters to know if your handgun is sighted for 6 o'clock POA or dead on POA, that's a bigger difference. Sadly, I don't know which apply to my own guns either. :-\ But even that doesn't matter for silhouette range unless you are trying to shoot the small targets. The man-sized and slightly smaller targets are still big enough to swallow this uncertainty.
-
^^^Pre made frames Pea............they are available at reasonable prices at Young Guns and I think Windward as well.
-
<snip>
I don't know at what range POI and POA are the same either.<snip>
You're not alone. No one knows that, except the shooter. Like everybody else told you, the pistol makes a huge difference, but the ammo makes an equally large difference. Guys that "roll their own" (reload) actually put quite a bit of work into finding a bullet/case/primer/powder combination that will shoot to POA at a given range.
-
^^^Pre made frames Pea............they are available at reasonable prices at Young Guns and I think Windward as well.
Just for kicks. What are they charging?
-
<$20 for this set up. That included the staplegun and targets
http://2ahawaii.com/index.php?topic=1550.0 (http://2ahawaii.com/index.php?topic=1550.0)
-
And most of the shooting is done with Beretta 92FS at 25 and 50 yards. POI is 2" higher at 50yards with 115gr FMJRN.
-
<$20 for this set up. That included the staplegun and targets
http://2ahawaii.com/index.php?topic=1550.0 (http://2ahawaii.com/index.php?topic=1550.0)
Teichi. I understand how much they cost to make, I was wondering what YG or WGS was SELLING them for.
-
I think security equipment sells them for $20 and I think WGS is $25.
I bought one at each of these places a couple of years back.
-
Key to the tiny targets is to shoot the beam they sit on, with a .45 I can get 3-4 at a time. ;D
-
HRA $10 IIRC. Maybe you can pick one up at the next fun shot.
-
They're extremely easy if you have a drill, a saw, and a place to drill and saw things, PeaShooter. If you're missing any of those, let me know, I'll make you one for the cost of materials from Home Depot.
-
Making a frame is cheap and easy. Making one well..........well that's something else. :)
-
Making a frame is cheap and easy. Making one well..........well that's something else. :)
Haha, true! The biggest problem with mine is that when I went to Home Depot for the lumber, all their 1x's looked like rejected rocking chair parts. The other problem is that I built it in five minutes, in my buddy's kitchen, with a reciprocating saw. Meh, it works, but I do wish I had built the thing the night before, in my garage; instead of at his house, the day we were going to the range. Being in a hurry is not conducive to quality work! :'(
-
You don't need a saw. Have the guys at home depot or lows cut the 8" board down to size for you. Cost you like 3 bucks + gas and hardware.
-
You guys are scaring me now.:'( I thought it was gonna be easy once I got around to trying to make one, like I figured the hardware store would just have exactly the right size of everything and I'd just get a hammer and pound them together or something with nails. :crazy: I have to saw and drill myself? That sucks. :)
I'm not particularly handy. I don't know how to make anything. :-\ My dad has tons of everything though and is very handy. I guess I have to let him help me. I probably need to make a lot of frames anyway, because I expect I will shoot them into pieces with my terrible aim.
-
If just build it to the sizes listed on the website it will fit fine.
-
You guys are scaring me now.:'( I thought it was gonna be easy once I got around to trying to make one, like I figured the hardware store would just have exactly the right size of everything and I'd just get a hammer and pound them together or something with nails. :crazy: I have to saw and drill myself? That sucks. :)
I'm not particularly handy. I don't know how to make anything. :-\ My dad has tons of everything though and is very handy. I guess I have to let him help me. I probably need to make a lot of frames anyway, because I expect I will shoot them into pieces with my terrible aim.
I just told you that you don't need a saw. You do need to drill it though, but that isn't hard at all.
-
The lumber store will make the cut for you. City Mill makes the 1st cut free, which is all you need.
I use 2" C-clamps to hold my frame together. No drilling required, and it disassembles completely for storage and repair.
-
I had city mill cut the wood to size and drilled 4 complete frames together on my kitchen counter in like 15 min. Super simple.
-
^^^Everything is always cool until the meathead next to you at Kokohead starts shooting out your frame. I swear most of the guys out there are cockeyed and have no idea how to line up their frame in the proper lane.
-
I saw a pretty slick folding setup for pistol frame today.
Basically an H. The top portion was held together by cardboard and binder clips. The cardboard needs to be exact width of the frame. Middle brace held to the legs by wing nuts and bolts. Loosen the wing nuts and all 4 legs fold together to fit in a trunk. I'll try and do one. Maybe next weekend.
-
I saw a pretty slick folding setup for pistol frame today.
Basically an H. The top portion was held together by cardboard and binder clips. The cardboard needs to be exact width of the frame. Middle brace held to the legs by wing nuts and bolts. Loosen the wing nuts and all 4 legs fold together to fit in a trunk. I'll try and do one. Maybe next weekend.
You should see the Corolla when it was loaded up for 8 students stands, tents, guns, ammo, training materials, and cardboard.... crazy stuff I tell you :). :geekdanc: