2aHawaii

Tools and Uses => Firearms and Accessories => Topic started by: dogman on May 25, 2015, 07:00:23 PM

Title: Cleaning handgun bores, nylon or brass brush?
Post by: dogman on May 25, 2015, 07:00:23 PM
Which do you use, if you use brushes?
I always buy nylon brushes, thought they will cause less wear on the barrel. The LGS was out of nylon but had brass. I was thinking does it matter? Maybe the brass brush cleans better?
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: macsak on May 25, 2015, 07:16:48 PM
Which do you use, if you use brushes?
I always buy nylon brushes, thought they will cause less wear on the barrel. The LGS was out of nylon but had brass. I was thinking does it matter? Maybe the brass brush cleans better?

d-man
you think that the brass brush going through the barrel wears more than the bullet being fired through the barrel at high speed and pressure?
 :wave:
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: Sodie on May 25, 2015, 08:10:30 PM
Brass.  According to https://www.tedpella.com/company_html/hardness.htm (https://www.tedpella.com/company_html/hardness.htm), brass is harder than copper (which I would guess allows the brass brush to remove copper fouling), and steel is harder than brass (which should keep the wear from the brass brush from doing  too much damage).

I'm with Macsak...  I figure the hundreds and hundreds of copper-jacketed bullets I've pushed down the bore put way more wear on it than running a brass brush through once in a while...

 :shaka:
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: dogman on May 25, 2015, 08:29:58 PM
I guess I'm just looking for reassurance that there are many who use brass / bonze brushes with no worries. I realize you wouldn't use them with copper dissolving solvents. The more I think about it the less I should worry about it . . .  :shaka:
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: macsak on May 25, 2015, 08:37:53 PM
I guess I'm just looking for reassurance that there are many who use brass / bonze brushes with no worries. I realize you wouldn't use them with copper dissolving solvents. The more I think about it the less I should worry about it . . .  :shaka:

 :worship:
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: Cpt.Englehorn on May 25, 2015, 08:47:38 PM
I use the brass brush, no issues at all, steel brush only comes out for guns that need it, normally projects, unless theres a stubborn leading/fouling issue.
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: Tom_G on May 25, 2015, 09:54:33 PM
Barrels are, at the least, hardened steel.  At the most, they are lined with something even harder.  The idea that swabbing them with something as soft as brass can be harmful is silly.  The idea that something as soft as nylon could remove deposits of metal, be it lead or copper, is equally silly. 
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: dogman on May 26, 2015, 05:35:42 AM
Barrels are, at the least, hardened steel.  At the most, they are lined with something even harder.  The idea that swabbing them with something as soft as brass can be harmful is silly.  The idea that something as soft as nylon could remove deposits of metal, be it lead or copper, is equally silly. 
Thanks for putting it that way, yes it is silly  :oops: , that's the reassurance I needed  :thumbsup:
 :closed:
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: suka on May 26, 2015, 05:47:55 AM
use a copper solvent , and a brass brush for heavy build ups. assuming you shot full metal jackets.

lead bullets just run a brass brush a few times to loosen the lead build up.

for powder residue a jag is sufficient. 

Polygon barrels , a jag is also sufficient .
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: zippz on May 26, 2015, 04:39:23 PM
handgun barrels will usually far outlive the handgun itself.  So pretty much a non-issue with brass brushes.
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: oldfart on May 26, 2015, 05:45:17 PM
I run a lot of lead bullets.

Dry brush with a brass brush First...NO oil or solvent.
Don't dip the brush into the bottle of solvent.
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: Inspector on May 26, 2015, 07:46:37 PM
I use brass/bronze brushes exclusively. I have one nylon brush and tried it a couple of times but the brass brush still did a better job after using the nylon brush.

I have never tried running a dry brush first. I will try it next cleaning day.
Title: Re: Cleaning handgun bores, nylon or brass brush?
Post by: oldfart on May 27, 2015, 12:55:41 AM
I use brass/bronze brushes exclusively. I have one nylon brush and tried it a couple of times but the brass brush still did a better job after using the nylon brush.

I have never tried running a dry brush first. I will try it next cleaning day.
...
The theory is that the dry brush would scrape lead out moa betta.
having oil or solvent on the bristles would allow them to slip over the deposits.

Then go at it with the solvents, etc.