2aHawaii
Tools and Uses => Reloading => Topic started by: kavawava on April 07, 2012, 05:14:08 PM
-
Hi everyone, sorry if this is a silly question. But how much (per round) is it costing everyone to reload 9mm (if you're even reloading 9mm). I know 9mm is fairly inexpensive to begin with, I'm currently paying 22 cens/round for factory 115gr ammo. Just curious to see how much the breakdown is to reload.
Thanks!
-
I reload 9mm, but not 115grn. I use 147 grn CMJ bullets from MG, and Vit N320 powder, both of which are on the more expensive side and it costs me right around $9.00 per 50 rounds. As soon as my MGs run out, I'll be switching to either moly or lead cast for costs savings. This should lower the cost to right around $6.00. It really depends on the components you use. Right now, it actually costs me less to load .45 ACP since I use lead cast bullets. Using a cheaper powder like TG would also lower the cost a bit, but there are downsides to consider. Primer prices are fairly consistent. I still save by reloading as I'm pretty sure factory 147s cost more than 115s unless they're on sale.
-
Here is what I am doing at this time:
Bullets: 115gr ~ $115/1k (Winchester/Remington/Montana Gold Bullet, JHP or FMJ, no lead) - $0.12/round
Primers: $30/1k - $0.03/round
Powder: $21/lb. (1200-1400 rounds per lb.) $0.02/round
Brass: $40/1k (mixed headstamp, once fired) or $120/1k - $0.04/round used or $0.12/round new
Total is $0.21 used or $0.29 new per round
This is for the first time you use the brass and assuming you don't get free brass. But every time you reload AFTER the first loading you pay only $0.17/round assuming you reuse the used brass. Depending on the quality of the brass and a few other things I have reused brass 4 or 5 times. So assuming I reuse used brass 4 times my total cost is an average of $0.18/round or $9/50 rounds. Your cost goes way down if you buy bullets by the case of 4000. Your cost per round is then $0.08/round. And if you can reuse your brass 5 times it also brings the cost way down. Another big savings is if you are next to someone shooting new 9mm ammo at the range and they are not saving the brass. I always offer to clean up their brass for them if they allow me to keep it. You get free once fired brass with the same headstamp usually. And now that you are reloading your own there is no reason why you have to load to full power and you can save a little powder per round and get up to 1400 rounds per pound of powder. You can literally bring your cost down to $0.12 or $0.13 per round or $6/50 rounds or $6.50/50 rounds by buying smart and getting free brass.
The thing is that no one factors in the cost of the reloading equipment and the time it takes to reload. If you factor in these things you have to reload a lot to make it worthwhile financially. But then if you decide to buy a .40 cal or a .45 ACP or a .357 Sig or .357 Magnum you can save a tremendous amount as the cost of commercial ammo is in the $25/50 round range and the cost for reloading components is not much more than 9mm. So for reloading only 9mm unless you shoot A LOT it would take you quite a few rounds to break even before you start saving money. But if you have larger calibers as well you will save even more per round by reloading.
With all that said I reload for other reasons besides cost savings. I reload so I can "Tune" a load to my gun to get the maximum accuracy out of it. And/or so I can reduce recoil making it more enjoyable to shoot more and for longer periods of time if I wish. Plus for me it is fun to try different loads, different powders, different bullets and weights, etc. For me it is just another aspect of the hobby that I include besides the shooting part.
Sources for components and prices:
1. Bullet prices per Montana Gold Bullet and Powder Valley per 1000. I tried to include shipping costs in the prices for bullets.
2. Primers are what I paid at the last gun show from Young Guns for Federal Small Pistol Primers not including tax.
3. Powder is Hodgens Titegroup I bought from OGC Tactical not including tax.
4. Brass prices are from Powder Valley for used brass and Starline for new brass.
-
Thanks for the references. I got close to 600 brass 9mm and maybe 200 .223. Now I know where to get some good pricing on bullets. Unless anyone wants to half some bullets and buy bulk.
-
Thanks for the references. I got close to 600 brass 9mm and maybe 200 .223. Now I know where to get some good pricing on bullets. Unless anyone wants to half some bullets and buy bulk.
I just ordered 10k 9mm 124 gr JHP from Precision Delta, but it is back ordered. I plan to call them on Monday to see how far backordered they are. The bullets come in boxes of 1k so you are welcome to get a box or two from me if you do not mind waiting, may be a couple of months. Price per 1k (since I am buying 10k) is $82.00 shipped with no usury. PM me if you are interested.
-
Brass prices are from Powder Valley for used brass and Starline for new brass.
Check out www.firstclassbulletsandbrass.com (http://www.firstclassbulletsandbrass.com). $18.99 per 500 with discounts for multiple purchases. AND, the brass is completely processed and blinged out. It could blind you . . . LOL. I purchased 9mm, 38 spl, and 357 mag brass from them a few months ago and I can tell you that the pictures of the brass on the website are accurate. Don't know what kind of polish they use, but it is shinier than brass out of the SS tumbler. It appears to glow.
Their bullet prices are higher since the lots are not in bulk. But, may work if you do not want to commit to a large purchase and find out that the bullet is not too accurate from your gun. YMMV
-
Check out www.firstclassbulletsandbrass.com (http://www.firstclassbulletsandbrass.com). $18.99 per 500 with discounts for multiple purchases. AND, the brass is completely processed and blinged out. It could blind you . . . LOL. I purchased 9mm, 38 spl, and 357 mag brass from them a few months ago and I can tell you that the pictures of the brass on the website are accurate. Don't know what kind of polish they use, but it is shinier than brass out of the SS tumbler. It appears to glow.
Their bullet prices are higher since the lots are not in bulk. But, may work if you do not want to commit to a large purchase and find out that the bullet is not too accurate from your gun. YMMV
Thanks for the link to this company. Prices are VERY good and will help lower the cost of reloading for everyone. I bookmarked their site. Unfortunately the website is down at the moment but I look forward to seeing where I spend more money! :geekdanc:
-
Hi everyone, thanks so much for the info! This really helps, especially you Inspector, there is a tremendous amount of info here.
I've been saving my once fired brass whenever I shoot just in case I may think about reloading in the future, got about 1000 of it. I'm currently a low to mid quantity shooter (about 300 rounds a week) and while 9mm isn't that terribly expensive I do hate waiting around for the gun stores to have a sale and also fighting traffic to sometimes pre-order then fighting it again to pick up the order.
Can anyone recommend a decent single stage press that will allow me to reload 9mm and still give me a chance expand and load other types of ammunition in the future?
Happy Easter everyone!
-
I picked up a lee single stage press from on here. Get action. New they sell for around $400 I believe. Single stage is like basic action. I saw a repeating press at the gun show for cheap. Should have picked that up when I had the chance.
-
see how far backordered they are.
I am told 2 weeks! :D
-
Woot. I'll take a thousand.
-
Woot. I'll take a thousand.
I'll PM you when it comes in. :shaka:
-
I find it's not worth the time and effort to reload jacketed 9mm, so I use lead for plinking and practice loads, which I think costs me about $7 for 50. With all the prep time included, I could load about 200 per hour, so figure I save $16/hour reloading which I figure is just over break even for me. Even plinking 5.56 rifle ammo is just slightly better than break even for cost and time.
I save alot more money for larger rifle calibers, and match ammo.
-
Can anyone recommend a decent single stage press that will allow me to reload 9mm and still give me a chance expand and load other types of ammunition in the future?
Happy Easter everyone!
I've had the Lee and now I have an RCBS. Either one will do fine work for you. It is the "Other" stuff you need to buy with the press like a scale and deburring tool and caliper, etc. that will set your wallet back a bit.
-
Hi everyone, sorry if this is a silly question. But how much (per round) is it costing everyone to reload 9mm (if you're even reloading 9mm). I know 9mm is fairly inexpensive to begin with, I'm currently paying 22 cens/round for factory 115gr ammo. Just curious to see how much the breakdown is to reload.
Thanks!
Is your cost with brass or aluminum casings?
-
Is your cost with brass or aluminum casings?
Cost is with brass cases
-
Cost is with brass cases
Actually this is how I get most of my brass for reloading I buy cheap ammo for plinking and practice and just shoot it up
The problem comes when you have a caliber that you can't buy cheaply such as :57
-
I don't reload 9 anymore. I figured that it was costing me about 18-20 cents / round w/o brass. I just pickup OGC's deals. The couple 3 cents a round saved is not worth it IMHO
-
I don't reload 9 anymore. I figured that it was costing me about 18-20 cents / round w/o brass. I just pickup OGC's deals. The couple 3 cents a round saved is not worth it IMHO
+1. Cheap 9mm ammo is a good reason to go with that caliber. I'm thinking that buying more ammo in lieu of the reloading equipment might be a better use of time (more time at range) and resources.
That said, making .45 or rifle ammo reloads and selling them might be good for making money to pay for the cheap 9mm ammo. :)
-
Just my opinion, but to the OP, if you're shooting 300 rounds a week consistently, reloading even for 9mm would cost a fair amount less than shooting factory ammo. Unless my math really sucks, (which it does at times), I've calculated that I save about $3 per 50 rounds(147grn). Shooting 300 rounds a week, that'll save you about $18 per session. Multiply that by 4 if you shoot every week, and that's $72 a month. It wouldn't take very long (maybe a year or so) for you to get back the money you put into reloading equipment (not counting bullets, primers, powder), and that's if you went with a progressive press instead of a single stage. Single stages can be had for a lot less, but if you can afford it, you may want to look into a progressive. I'm not sure how long it takes to load 300 rounds on a single, but I know it takes me less than an hour, (taking my time) to load 300 on a progressive (I use a Dillon 550B). That leaves a whole lot of time for the other stuff I need to get done.
A lot of experienced people will say to start on a single stage, but a good progressive press, and good safety habits, can be just as safe while being a lot more efficient, especially for pistol cartridges. If you're on Oahu, you may want to take a ride out to WGS and talk to Joe and see what advice he has. I picked up my Dillon 550B from him, he's a great guy to deal with. I'd definitely recommend reloading, especially with your round count and the fact that you're considering getting into other higher priced calibers.
-
I never really thought about it but I too don't reload for 9mm, given the cost of buying jacketed bullets. I used to reload 9mm years ago (Sierra 115 gr. JHC) but over the years I've stockpiled enough 9mm to the point where I don't have to reload for a long time. Remember when Sports Authority used to sell white box 9mm for $4.99 a box? Those were the good old days!
I reload for .45, since I shoot mostly lead SWCs and the savings can be substantial. I'm always hunting around for good deals on ammo, but nowadays if I buy factory ammo it is .22 LR.
The cost of a good press and dies will be quickly amortized, and once you've recouped the cost of your equipment, it's free!
-
Thanks for the link to this company. Prices are VERY good and will help lower the cost of reloading for everyone.
Just a heads up . . . I received the brass in about a week the last time I ordered from them. But, I ordered some (2k) 9mm brass from them about 2 weeks ago and have not received it yet.
I did a little research and it seems that they get backlogged once in a while (kinda like PD), but you will eventually get your order. However, unlike PD, they charge your cc immediately even though it may take a month for you to receive your order. :-\
-
Just a heads up . . . I received the brass in about a week the last time I ordered from them. But, I ordered some (2k) 9mm brass from them about 2 weeks ago and have not received it yet.
I did a little research and it seems that they get backlogged once in a while (kinda like PD), but you will eventually get your order. However, unlike PD, they charge your cc immediately even though it may take a month for you to receive your order. :-\
I think for me this would be okay as long as they let me know what is going on. I hate companies that charge your card without telling you the item is backordered. Then after a while it doesn't show up you have to contact them and then they act like they did nothing wrong. >:(
So far I have been pretty lucky with the companies we have mentioned here. They communicate pretty well. :thumbsup:
-
I just ordered 10k 9mm 124 gr JHP from Precision Delta, but it is back ordered. I plan to call them on Monday to see how far backordered they are. The bullets come in boxes of 1k so you are welcome to get a box or two from me if you do not mind waiting, may be a couple of months. Price per 1k (since I am buying 10k) is $82.00 shipped with no usury. PM me if you are interested.
With ammo available at prices like that, it's really hard to justify the expense and time of reloading unless you want to fine-tune your ammo for precision shooting.
-
With ammo available at prices like that, it's really hard to justify the expense and time of reloading unless you want to fine-tune your ammo for precision shooting.
That's not ammo he ordered. Those are just the bullet component. That is $0.082 per bullet plus brass case plus powder plus primer. Powder is about $0.01 and a primer about $0.03. So he is up to $0.12 per round depending on where he got his brass. Lately I have been using a figure of $0.03 per round for new brass ($0.12/casing with 4 uses which makes it $0.03/use). And that goes down further if I use the casing 5 times and even further if I buy used brass and free if you get range brass.
Right now I am reloading at about $0.15 per round and I can get that down to about $0.12 per round if I go with components I don't want to use. That is what I make plinking rounds with. Maybe even $0.10 per round if I went with free range brass. The last sale that OGC had on bulk 9mm ammo was $239/1000 or $0.239 per round for Magtech. At today's prices it is worth reloading for me and getting quality fine tuned ammo for my pistols.
-
That's not ammo he ordered. Those are just the bullet component. That is $0.082 per bullet plus brass case plus powder plus primer. Powder is about $0.01 and a primer about $0.03. So he is up to $0.12 per round depending on where he got his brass. Lately I have been using a figure of $0.03 per round for new brass ($0.12/casing with 4 uses which makes it $0.03/use). And that goes down further if I use the casing 5 times and even further if I buy used brass and free if you get range brass.
Right now I am reloading at about $0.15 per round and I can get that down to about $0.12 per round if I go with components I don't want to use. That is what I make plinking rounds with. Maybe even $0.10 per round if I went with free range brass. The last sale that OGC had on bulk 9mm ammo was $239/1000 or $0.239 per round for Magtech. At today's prices it is worth reloading for me and getting quality fine tuned ammo for my pistols.
That.
And, I've also noticed that my reloads are not as snappy as factory ammo.
Plus, once you start reloading hollow points for home defense (despite what experts say about using factory ammo only), then your cost goes down from $1+ to $0.25 per round. Not that I'm stockpiling HD ammo ::)
-
That.
And, I've also noticed that my reloads are not as snappy as factory ammo.
Plus, once you start reloading hollow points for home defense (despite what experts say about using factory ammo only), then your cost goes down from $1+ to $0.25 per round. Not that I'm stockpiling HD ammo ::)
That.
I use Titegroup for all of my handgun reloading. And while it is not optimum for my .357 Magnum it is for my 9mm. And if I were to believe the velocity stated in all of my books, I have noticed that using the same weight bullet at the same velocity as factory ammo, my felt recoil is significantly less than factory ammo. I thought it was just me but after a little research on the Internet I believe it is the powder that is causing this.
I am still trying to decide which HD bullet I want to try loading for. Are you loading anything new like Hornady's newest? Or Winchester"s newest? I am thinking of 147gr in 9mm this time over the 124gr I was loading for.
-
I am still trying to decide which HD bullet I want to try loading for. Are you loading anything new like Hornady's newest? Or Winchester"s newest? I am thinking of 147gr in 9mm this time over the 124gr I was loading for.
I've been using Vihtavuori N320 for 9mm, W231 for 38 spl & W296 for 357. But, the load data for W296 is way off on Hodgdon's Reloading Data Center. I loaded up a bunch and started with the lowest powder loaded round (21.0 gr) and the primer was pancaked. I did not shoot anymore and had to pull apart 39 bullets. I am now loading at 17.0 gr and it may still be a bit hot.
Using Golden Sabre for 9mm 124 gr & Hornady XTP 125 gr for 38 spl & 357 mag. Cannot find Hornady's latest, Critical Defense, available yet other than as loaded ammo. Also, got a few Hornady FTX 140 gr for 357.
-
I've been using Vihtavuori N320 for 9mm, W231 for 38 spl & W296 for 357. But, the load data for W296 is way off on Hodgdon's Reloading Data Center. I loaded up a bunch and started with the lowest powder loaded round (21.0 gr) and the primer was pancaked. I did not shoot anymore and had to pull apart 39 bullets. I am now loading at 17.0 gr and it may still be a bit hot.
Using Golden Sabre for 9mm 124 gr & Hornady XTP 125 gr for 38 spl & 357 mag. Cannot find Hornady's latest, Critical Defense, available yet other than as loaded ammo. Also, got a few Hornady FTX 140 gr for 357.
I am kinda old school when it comes to SD rounds. Bigger (heavier) is better. In 9mm I was buying 124gr SD factory ammo cuz I know my guns prefer that weight bullet. But then it dawned on me I am not trying to get 1"-2" groups at 25yds. So I am re-thinking the 124gr and am considering 147gr this time around. Especially since I am loading them myself this time. The reputation of the .357 125gr JHP is legendary. But I think I will go with 158gr JHP this time since I am loading them myself.
I know this sounds weird but I have had similar issues with the Lyman Reloading Manual. I loaded some .357 with so little Titegroup that it would not ignite reliably and had some squibs and lots of unburned powder. I loaded near the bottom end of their scale but not even the lowest. Sierra and Hornady started the same loading at least 25% heavier powder, same velocity. Then with another loading (lead bullet) my loads were so hot that I was getting terrible leading in my barrel. After looking through the Sierra and Hornady books I found the load was way too hot for lead even though I was at the low end of the range in the Lyman book. Sierra and Hornady books were much lower for a lead bullet. I now rely more on my Sierra and Hornady books and look up Hodgens data on the net. If I can't verify a load from these three sources as being similar I won't load it or I rely on the Sierra data. Sierra seems to have performed more thorough loading in the cartridges I load. For instance in .223 Remington they list loads for a semi-auto (AR type) rifle and much different loadings for a bolt gun.
-
I don't load for HD, but for range use or USPSA matches, its hard to beat 147grn. bullets and N320. Very little muzzle flip, and with jacketed bullets, very clean. I use N320 with 147 grn. CMJ from Montana Gold, and with 200 grn. LSWC from S&S. I used to use TG, but at 3.3grn. I could pull the handle 3 times before the powder over-filled the case. A double would be way too easy to overlook. TG is cheap but I found it caused a little more muzzle rise than Vit when loaded to the same PF. Its also a bit dirtier even with jacketed, and way smokier with lead. It will definitely save money when compared to the Vit powders, but for the added safety benefit, I'd rather use a powder that takes up more space in the case.
-
Mahalo gentlemen for your "data points."
@mnpfamily - How many times do you reload your pistol brass? I have seen posts (by competition shooters) of upwards of 20 times.
-
I don't think I'm quite at 20 reloads on my brass yet, but have to be getting close. I've got a bunch that I can barely make out the headstamp. With my 9mm reloads, if I use them at a match, I usually just leave them. There are a lot of open division guys shooting 9mm major, I really don't want to risk picking up their brass by mistake. For me anyway, I think I lose the brass (even using a brass catcher at the range), before it becomes unusable. My .45 brass seems to be in better shape than my 9mm though. It could be because I use the "U" die to resize 9mm and a regular resizing die for .45.
-
Cool! I am no where near that many reloads per case & good to know my brass has more life left. :thumbsup:
-
One thing you might want to consider though is most who load for USPSA try to get fairly close to just above what's needed to make either minor PF or major PF (while allowing some cushion). These loads feel a lot softer than factory ammo so this may play a factor in brass life. Another interesting side note, those pieces of brass that I've reloaded the most have become shorter. In fact they've shrank enough that I actually had to adjust my seating die a little to keep OAL consistent with load data (I load 9mm a little on the short side to begin with). I haven't reached this point with the ACP cases yet though.
-
All this talk of loading self defense rounds and I couldn't wait any longer and I ordered a bunch of Hornady XTP JHP bullets from Cabelas. They were on sale with $5 shipping. So I bought 124gr and 147gr in 9mm and 125gr and 158gr in .357.
So do any of you know if the guys over on the rifle side or the silhouette side will let us shoot into milk jugs stuffed with wet newspaper? I would love to try and do our own bullet expansion and retention tests.
-
All this talk of loading self defense rounds and I couldn't wait any longer and I ordered a bunch of Hornady XTP JHP bullets from Cabelas. They were on sale with $5 shipping. So I bought 124gr and 147gr in 9mm and 125gr and 158gr in .357.
So do any of you know if the guys over on the rifle side or the silhouette side will let us shoot into milk jugs stuffed with wet newspaper? I would love to try and do our own bullet expansion and retention tests.
I dont think they will let you shoot anything there!
-
I dont think they will let you shoot anything there!
Yeah, I figured they won't. But I would love to find somewhere that I can run some tests. I am sure there are a few others here who would like to join in as well.
-
Yeah, I figured they won't. But I would love to find somewhere that I can run some tests. I am sure there are a few others here who would like to join in as well.
May try asking one of the clubs that utilize the shooting bays.
Do you chrony your loads?