2aHawaii

Tools and Uses => Reloading => Topic started by: Inspector on October 18, 2020, 11:42:53 AM

Title: Powder Coating
Post by: Inspector on October 18, 2020, 11:42:53 AM
Tried my first batch of powder coating today...
Title: Re: Powder Coating
Post by: macsak on October 18, 2020, 11:45:36 AM
Tried my first batch of powder coating today...

heads
Title: Re: Powder Coating
Post by: Lihikai on October 18, 2020, 11:47:00 AM
What kind of powder coat are you using?
Title: Re: Powder Coating
Post by: Inspector on October 18, 2020, 01:04:09 PM
What kind of powder coat are you using?
The general consensus is that Eastwood Ford Light Blue is the best and easiest to use. So that is what that is. I also ordered their dark green as everyone is saying it coats as well as the Ford Light Blue. Once I get good at this I’ll try some of the colors that appeal to me. I’m still in the learning stage.

I have been following a guy on YouTube named Elvis Ammo (I follow a bunch of others as well) and he came up with a low temp process using this powder coat. I went to Goodwill and bought a decent looking toaster oven. When I tried it this morning I couldn’t get the temp down far enough and melted my boolits! 😂 went back to Goodwill today and bought this filthy dirty toaster oven and at works great! I just have to get the temps adjusted correctly.
Title: Re: Powder Coating
Post by: oldfart on October 18, 2020, 04:52:19 PM
Are you sizing?
Title: Re: Powder Coating
Post by: Heavies on October 18, 2020, 08:31:53 PM
Looks good!
Title: Re: Powder Coating
Post by: Inspector on October 19, 2020, 03:21:51 AM
Are you sizing?
I have not yet, but I intend to. Just have not got around to it. I bought a Lee swage kit. As soon as I size them I am going to load ‘em up and choot ‘em!

I realized after so many hours of casting, a 2 bullet mold is too small. I will be replacing it with a 6 bullet mold.  :rofl:

So far I am getting pretty good results. Just not as good as I would like. I think I just need some practice.
Title: Re: Powder Coating
Post by: Inspector on October 19, 2020, 03:24:03 AM
Looks good!
Thanks B! The photo makes them look better than in person. But I think they are good enough to shoot.
Title: Re: Powder Coating
Post by: Rocky on October 19, 2020, 05:15:15 PM
The photo makes them look better than in person. But I think they are good enough to shoot.
I wanted to slide a photo of certain "person(s)" in here but you know, "discretion".  :rofl: :rofl: :rofl:
I think it is 2a quote worthy tho.
 :wave:
Title: Re: Powder Coating
Post by: Inspector on October 20, 2020, 01:35:03 AM
I wanted to slide a photo of certain "person(s)" in here but you know, "discretion".  :rofl: :rofl: :rofl:
I think it is 2a quote worthy tho.
 :wave:
That’s really funny! I didn’t think about what I said until you pointed it out.

Maybe you should start a new thread... with photos...   :rofl:
Title: Re: Powder Coating
Post by: oldfart on October 20, 2020, 05:29:07 AM
I have not yet, but I intend to. Just have not got around to it. I bought a Lee swage kit. As soon as I size them I am going to load ‘em up and choot ‘em!

I realized after so many hours of casting, a 2 bullet mold is too small. I will be replacing it with a 6 bullet mold.  :rofl:

So far I am getting pretty good results. Just not as good as I would like. I think I just need some practice.
...
If the diameter is pretty close, no need size.
Down side is if they're too big then the ammo may have trouble chambering.
Generally, the less squeezing you do to the bullet, the better the accuracy.
Try it.
Title: Re: Powder Coating
Post by: Inspector on October 20, 2020, 06:21:48 AM
...
If the diameter is pretty close, no need size.
Down side is if they're too big then the ammo may have trouble chambering.
Generally, the less squeezing you do to the bullet, the better the accuracy.
Try it.
I’ll check them out when I have some time. I have been really busy lately so casting and powder coating have gone by the wayside. I think the boolits came out at .360”-.361” out of the mold for a .357/.38. So how close is close? I’m sure the powder coating added another .001”-.002” to the diameter.

BTW, I am using the low heat/temp method of powder coating. I have been reading that bringing the boolits up to 400 degrees softens them bringing the BHN down. So I am trying the low temp of 250 degrees as to keep the BHN up at around 16 where I’m at before the powder coating.