Post by: Inspector on March 28, 2021, 01:05:43 PM
I have two areas where I work on my guns, cases and reloading. I keep all of my case prep stuff out in my garage for dust reasons. I also clean my guns and cast lead boolits out in the garage for fume reasons. I do all my resizing, reloading and most of my gun repairs in my reloading room. I have two presses. I have a Lee 4 hole turret press and an RCBS Rockchucker single stage. I reload most of my pistol cartridges on the Lee and all my rifle cartridges on my Rockchucker. I reload for 8 different pistol cartridges and 10 different rifle cartridges. Most cartridges I reload for are common calibers but a few are specialty and obsolete cartridges. I also swage primer pockets and boolits on my Rockchucker. When it is warm outside I can work in the garage or the house. But when it is too cold out I leave all my case prep projects outside until it gets warm.
Today I sat down and cleaned primer pockets on 300 rounds of 9mm and 100 rounds of 7.62x25 Tokarev. I had previously sized and cleaned the cases and trimmed them if necessary. But we got a cold snap for 2-3 weeks so I left them in the garage until it warmed up today. I cleaned some dies that I had not touched for several years and were filthy. I emptied my ultrasonic cleaner of the dirty cleaning solution. That had been sitting since it got cold.
My brother and his family came and visited me a couple of months ago. He brought me a one pound coffee can of my father’s 9mm mystery reloads. My father taught me how to reload but he was not one to keep copious records and be detailed and careful when reloading. The can is full to the brim. And there was a slip of paper that said “125gr” that’s it. No date, no powder, no charge info. I suspect these were reloaded sometime in the mid 1980’s. Knowing my father he used Sierra 125gr 9mm FMJ seconds he bought from the Sierra factory when it was still located in SoCal 25 miles from his house. Also I know all he ever bought were CCI small pistol primers. As far as powder is concerned the weights varied greatly from 5.2gr-6.5gr. I took apart 16 rounds to study them. First, the COL was waaaaay too long. About 0.15” too long according to my Sierra manual. And while it was tough, I could not tell if there was a crimp. Fifteen out of 16 fit my gauge. And a couple of rounds the primer was not inserted all the way in. After taking them apart I noticed the powder was round flakes and medium gray in color but there was about 10% were dark gray to black flakes. Knowing my father he used mostly Herco and Bullseye powders. I have the new formulated Bullseye and it didn’t look like it at all. And I don’t remember what Herco looks like. I used Unique back then and it is possible he may have used some of my Unique. But it didn’t look like it at all. I decided to disassemble all of them, resize the cases with the primer in place, reset the primer farther into the case where applicable and reload them using 3.9gr of Bullseye. I already did this to 100 rounds for a proof of concept and they worked fine for practice ammo. Though they were were not terribly accurate at 10 yards. I started on the first 50 today. Disassembled them, resized them, set the primers back and loaded them up with Bullseye and seated and crimped the bullets. They are running through my dry tumbler right now to shine them up and get rid of the tarnish and dirt. This is going to take quite a while to get through the entire coffee can.
Post by: aletheuo137 on March 28, 2021, 01:14:35 PM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on March 28, 2021, 01:39:47 PM
I like hodgdon and accurate powders. My favorites are 44mag and 357mag. Either moderate cowboy loads up to H110 heavy loads
Currently I'm sorting out all the crap I've collected and trying to use up the older stuff I have to make room to store the newer stuff. Sometimes I find things I forgot I still have. :shaka:
Post by: aletheuo137 on March 28, 2021, 01:46:14 PM
Currently I'm sorting out all the crap I've collected and trying to use up the older stuff I have to make room to store the newer stuff. Sometimes I find things I forgot I still have. :shaka:
I have that problem too!
Sent from my SM-A102U using Tapatalk
Post by: Inspector on March 28, 2021, 02:36:42 PM
I reload mostly handgun calibers. 357, 44, 45acp, 9mm, and a little 223 and 308.I think we all have that problem. For some reason I thought I was low on 9mm cases. So I ordered 1k that I found at a decent price. When I went to put it away in my garage I found 1k each 223, 38 and 357 that I didn’t know I had. Oh, and I found another 2k 9mm cases I didn’t remember having. I would not have ordered that 1k cases if I had remembered the 2k I already had. :rofl:
I like hodgdon and accurate powders. My favorites are 44mag and 357mag. Either moderate cowboy loads up to H110 heavy loads
Currently I'm sorting out all the crap I've collected and trying to use up the older stuff I have to make room to store the newer stuff. Sometimes I find things I forgot I still have. :shaka:
Post by: stangzilla on March 28, 2021, 05:12:23 PM
Post by: Inspector on March 28, 2021, 05:36:30 PM
I reload mostly handgun calibers. 357, 44, 45acp, 9mm, and a little 223 and 308.I forgot to ask how you like the Accurate powders? Never tried any. I used mostly DuPont/Hercules powders until they became Alliant for handgun. I still use them but I use Hodgdon powders more now. And I used IMR powders for rifle calibers mostly and now I use Hodgdon more. I still like the old favs from Alliant and IMR but certain Hodgdon powders just seems to fill my needs better.
I like hodgdon and accurate powders. My favorites are 44mag and 357mag. Either moderate cowboy loads up to H110 heavy loads
Currently I'm sorting out all the crap I've collected and trying to use up the older stuff I have to make room to store the newer stuff. Sometimes I find things I forgot I still have. :shaka:
I have this weird issue that most of my reloading manuals are old. So they only list IMR, Hercules/Dupont and Accurate powders. Before Hodgdon and others became mainstream. Thank goodness for the Internet.
Post by: macsak on March 28, 2021, 07:18:51 PM
Post by: dogman on March 28, 2021, 07:42:47 PM
Post by: oldfart on March 28, 2021, 11:47:35 PM
4.5 grains of cfe pistol. This bullet is a work in progress. The velocity is perfect but accuracy was just ok.
It should be better.
Post by: Inspector on March 29, 2021, 03:01:23 AM
I ran off a hundred rounds of 9mm_135 polymer coated truncated cone bullets.It’s operator not the bullet’s fault! :rofl:
4.5 grains of cfe pistol. This bullet is a work in progress. The velocity is perfect but accuracy was just ok.
It should be better.
Post by: oldfart on March 29, 2021, 03:17:50 AM
It’s operator not the bullet’s fault! :rofl:==========
I won't argue with that.
It's hard to shoot straight when you live in paradise and distracted by palm trees, mai tais and skanky hoes.
You're so lucky to live in Arizona where all you got there is steers and queers.
Post by: Inspector on March 29, 2021, 03:44:40 AM
==========I love you, too OF!!! :love: :love: :love:
I won't argue with that.
It's hard to shoot straight when you live in paradise and distracted by palm trees, mai tais and skanky hoes.
You're so lucky to live in Arizona where all you got there is steers and queers.
Post by: Inspector on March 29, 2021, 06:01:40 AM
I had received the brass several months ago and I lubed, sized and then put them through my ultrasonic cleaner and laid them out to dry. I then placed them in my airtight container with desiccant in it. When I opened it up this morning, there was a lot of moisture in the container. Apparently they were not completely dry when I put them away. So I put them back out to dry in my garage. I will prime them and start reloading them this afternoon. I will use two loads. I will use a full power load of 28.0gr of H4895 for a 139gr bullet for about 2,100 fps. And I will also load a light load using the same bullet over 18-20gr of H4895 for about 1,600fps. I may even load up some using Trail Boss.
Post by: oldfart on March 29, 2021, 06:50:26 AM
Post by: Inspector on March 29, 2021, 06:58:36 AM
Is the carcano a 91 with a 4x scope?Nope. It’s the later carbine model with stock military irons that suck.
Post by: oldfart on March 29, 2021, 07:14:07 AM
Nope. It’s the later carbine model with stock military irons that suck......
Wait a minute....are you saying your shooting sucks because of the iron sights?
Post by: Inspector on March 29, 2021, 07:17:06 AM
.....Nope. I’m saying my shooting suck s cuz my vision is bad. :rofl:
Wait a minute....are you saying your shooting sucks because of the iron sights?
Post by: Inspector on March 29, 2021, 07:17:56 AM
.....While I have not shot this rifle yet it is not known for its accuracy. And I’m not know for my accuracy either! :rofl:
Wait a minute....are you saying your shooting sucks because of the iron sights?
Post by: oldfart on March 29, 2021, 08:01:54 AM
While I have not shot this rifle yet it is not known for its accuracy. And I’m not know for my accuracy either! :rofl:...
Oh ok...I get it.
So far you have blamed the:
1. Iron sights
2. The rifle itself
3. Your old eyeballs
And you haven't even shot the thing yet.
While you're at it, let's blame:
The sun
The wind
The primer
Brass
Bullet
Powder
primer
The water
Ànd the taco you ate for dinner.
Post by: Inspector on March 29, 2021, 08:08:24 AM
...Sure. Whatever works. I still love you OF! :love:
Oh ok...I get it.
So far you have blamed the:
1. Iron sights
2. The rifle itself
3. Your old eyeballs
And you haven't even shot the thing yet.
While you're at it, let's blame:
The sun
The wind
The primer
Brass
Bullet
Powder
primer
The water
Ànd the taco you ate for dinner.
Post by: stangzilla on March 29, 2021, 08:38:19 AM
loaded some with AA#7
(https://live.staticflickr.com/65535/51079908313_4952360730_b.jpg)
Post by: drck1000 on March 29, 2021, 10:27:05 AM
Post by: Inspector on March 31, 2021, 03:52:51 PM
Now back to 223/5.56 loading...
Post by: stangzilla on March 31, 2021, 04:24:05 PM
i have some old H110 powder and some old LPP i got on a couple of trades i should test out
Post by: drck1000 on April 01, 2021, 02:43:17 PM
Post by: stangzilla on April 02, 2021, 07:15:32 AM
I forgot to ask how you like the Accurate powders? Never tried any. I used mostly DuPont/Hercules powders until they became Alliant for handgun. I still use them but I use Hodgdon powders more now. And I used IMR powders for rifle calibers mostly and now I use Hodgdon more. I still like the old favs from Alliant and IMR but certain Hodgdon powders just seems to fill my needs better.
I have this weird issue that most of my reloading manuals are old. So they only list IMR, Hercules/Dupont and Accurate powders. Before Hodgdon and others became mainstream. Thank goodness for the Internet.
i like the Accurate powders. i've been using #9 for a while. it burns clean, i notice my gun isn't that dirty after shooting. its accurate. and can be loaded to nearly comparable velocity of H110. it has a lower flash than H110. i use #9 for 44mag and 357mag.
I just started to use #7. i notice it often overcharges in my Hornady auto charge dispenser. it is a fine powder, so that may not work so well in the Hornady auto charge dispenser. but the #9 works well with the Hornady unit
i have to load more with #7 and #5 to really get a feel for them
Post by: stangzilla on April 02, 2021, 07:21:43 AM
first time i'll be loading these bullets. looks like the regular LSWC, but the head part looks a little larger on the Keith style. price was really good from Stateline. i 'll probably order again when they get in stock. right now they are sold out on just about everything
nothing says 44 magnum quite like Elmer Keith :thumbsup: :thumbsup:
(https://live.staticflickr.com/65535/51089350166_ea61714883_b.jpg)
Post by: Inspector on April 02, 2021, 11:09:25 AM
I finished up my 100 rounds of 6.5 Carcano in my dry tumbler.
I loaded 100 rounds of 7.62x25 Tokarev. They will go in the dry tumbler next.
Post by: aletheuo137 on April 02, 2021, 06:27:40 PM
Sent from my SM-A102U using Tapatalk
(https://uploads.tapatalk-cdn.com/20210403/fbc6c5cf26b1a27f4c340788a41a2514.jpg)
Post by: Inspector on April 03, 2021, 12:22:33 AM
Clean of rust of a Walther P38!Nice!
Sent from my SM-A102U using Tapatalk
(https://uploads.tapatalk-cdn.com/20210403/fbc6c5cf26b1a27f4c340788a41a2514.jpg)
Post by: Inspector on April 05, 2021, 01:01:56 PM
My nephew is coming up this weekend so I can try out his new Stribog 9mm pistol. He wants to try as many different types of 9mm ammo in it so I told him I have 4 different types for him to try. Including these redone reloads.
Post by: drck1000 on April 05, 2021, 01:05:43 PM
(https://uploads.tapatalk-cdn.com/20210405/2411d04d7b05271c1eba3f10a4f7a6f4.jpg)
Post by: Inspector on April 05, 2021, 01:22:02 PM
Getting ready for next roundNiCE! That’s a lot of money right there! :worship:
[SNIP]
Post by: drck1000 on April 05, 2021, 01:27:26 PM
NiCE! That’s a lot of money right there! :worship:You should see the rest of my stash. Hypothetically of course.
Post by: Inspector on April 05, 2021, 01:29:28 PM
You should see the rest of my stash. Hypothetically of course.You should have seen my stash before I moved. :(
Post by: stangzilla on April 05, 2021, 01:42:27 PM
MK machining makes an insert that makes it not overcharge so much, its $14 for 3 of them of different sizes
but i did some online researching and found that someone used a expanding nut from Home Depot. its Everbilt expansion nut, #8-32 x 15/32 inches. good thing is on Home depot site it gave me the aisle number and bin number so was easy to find. didn't have to ask one of the workers that don't know shit either, so saved time by not consulting with them
we'll see how good it works
and was only 77 cents at home depot
Post by: Inspector on April 05, 2021, 01:48:36 PM
with certain powders in my Hornady auto charge powder dispenser, it overcharges more than i would like it toI had the same problem with my RCBS Chargemaster. Heavies turned me on to a hack using a McDonalds straw cut in a certain way. And it works very well. Has been working for 7 or 8 years now. Price = $0
MK machining makes an insert that makes it not overcharge so much, its $14 for 3 of them of different sizes
but i did some online researching and found that someone used a expanding nut from Home Depot. its Everbilt expansion nut, #8-32 x 15/32 inches. good thing is on Home depot site it gave me the aisle number and bin number so was easy to find. didn't have to ask one of the workers that don't know shit either, so saved time by not consulting with them
we'll see how good it works
and was only 77 cents at home depot
Post by: drck1000 on April 05, 2021, 01:51:00 PM
with certain powders in my Hornady auto charge powder dispenser, it overcharges more than i would like it toI have the MK Machining "over"sert. It works very good for facilitating accurate powder trickle. I have the occasional over, but pretty rare. The over-sert nature of the one have does make you be more careful in getting the pan off the scale though.
MK machining makes an insert that makes it not overcharge so much, its $14 for 3 of them of different sizes
but i did some online researching and found that someone used a expanding nut from Home Depot. its Everbilt expansion nut, #8-32 x 15/32 inches. good thing is on Home depot site it gave me the aisle number and bin number so was easy to find. didn't have to ask one of the workers that don't know shit either, so saved time by not consulting with them
we'll see how good it works
and was only 77 cents at home depot
My set came with three inserts, which I assume is to account for variations in models. Let me know if you want to try the other two inserts. I've heard the McDonald's straw hack is just as good, but I was ordering something else from MKM, so added the insert.
Post by: stangzilla on April 05, 2021, 01:57:56 PM
I had the same problem with my RCBS Chargemaster. Heavies turned me on to a hack using a McDonalds straw cut in a certain way. And it works very well. Has been working for 7 or 8 years now. Price = $0
in my research i came across the mcdonalds straw mod. if the expanding nut doesn't work, thats next on my list
I have the MK Machining "over"sert. It works very good for facilitating accurate powder trickle. I have the occasional over, but pretty rare. The over-sert nature of the one have does make you be more careful in getting the pan off the scale though.
My set came with three inserts, which I assume is to account for variations in models. Let me know if you want to try the other two inserts. I've heard the McDonald's straw hack is just as good, but I was ordering something else from MKM, so added the insert.
thats probably what i was looking at the "over" cert. i'll let you know if my modifications fail, hopefully they don't :shaka:
Post by: drck1000 on April 05, 2021, 02:03:25 PM
in my research i came across the mcdonalds straw mod. if the expanding nut doesn't work, thats next on my listCool. I was going the manual/spoon method until I sprung for the Chargemaster. It's much faster. Only humbug part is when I change powders between batches. Forgetting to close the drain spigot thingy was one lesson learned pretty quickly. :(
thats probably what i was looking at the "over" cert. i'll let you know if my modifications fail, hopefully they don't :shaka:
:rofl:
Post by: macsak on April 05, 2021, 05:11:59 PM
I had the same problem with my RCBS Chargemaster. Heavies turned me on to a hack using a McDonalds straw cut in a certain way. And it works very well. Has been working for 7 or 8 years now. Price = $0
no plastic straws here any more
:'(
Post by: Inspector on April 05, 2021, 05:19:30 PM
no plastic straws here any moerThere was a story last year that they were selling on eBay for as much as $1k. :o
:'(
If you want I’ll see if they still have them at the McD’s near me and I’ll grab a few and send them to you.
Post by: stangzilla on April 09, 2021, 07:46:52 AM
side by side comparison of Hunter's Supply SWC on the left, and Stateline Keith bullet on the right. the Keith head of the bullet is bigger. less of the projectile will be in the brass if you compare the crimp groove on each one.
plan is to load a good warm load using AA#7. since it's a Keith bullet, I didn't want to go Trailboss, a little hotter would be nice, but I'll save the H110 for JHP bullets.
(https://live.staticflickr.com/65535/51103932796_f7ae2d0874_b.jpg)
Post by: aletheuo137 on April 09, 2021, 12:25:13 PM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on April 09, 2021, 12:31:29 PM
Nice primers!
Sent from my SM-A102U using Tapatalk
:shaka:
Post by: Inspector on April 09, 2021, 12:52:06 PM
I reloaded 100 rounds of 300 Blackout plinking ammo using 110gr Nosler Varmageddon over H110 with a Small Rifle Magnum Primer. I was lucky enough to pick up the heads in bulk at 12 cents a piece. I should have bought more. I dumped them into the vibratory tumbler. I need to process more brass so I can load some more rounds.
It’s time to get back to casting some new boolits for my 38, 357 and 45.
Post by: jc2721 on April 09, 2021, 01:42:18 PM
Yesterday I saw 124 gr. JHP bullets (not heads or boolits) for sale at one of my suppliers, by the time lunch rolled around they were sold out.
I have noticed that pistol powder has been selling out quickly--no 231, BE, HP 38, tight group, etc., is available, just some Unique and trailboss. I have enough unique to last a few years, about enough to match my primer supply, lol.
Sent from my SM-G970U using Tapatalk
Post by: Inspector on April 09, 2021, 03:19:01 PM
Well, for the past couple of weeks I've been reloading 38 and 45--about a .50 cal can of each. Ordered more bullets about 10 days ago but they haven't shown up yet.I have enough Unique to last me a year I think. About 2 years worth of Titegroup. And about 6 months worth of Red Dot, Green Dot and Bullseye. And probably 2-3 years worth of H110. And yet I still feel I don’t have enough pistol powder. And I will buy more if I see some available for sale. I have choke rifle powder.
Yesterday I saw 124 gr. JHP bullets (not heads or boolits) for sale at one of my suppliers, by the time lunch rolled around they were sold out.
I have noticed that pistol powder has been selling out quickly--no 231, BE, HP 38, tight group, etc., is available, just some Unique and trailboss. I have enough unique to last a few years, about enough to match my primer supply, lol.
Sent from my SM-G970U using Tapatalk
I need more bullets (9mm mostly). I am using up what I have left and I’m casting my own (38/357 & 45). In a pinch I can cast 9mm as well. I just prefer to use jacketed bullets in 9mm. After I get better at casting and powder coating my pistol boolits I will start casting rifle boolits.
Post by: oldfart on April 11, 2021, 08:52:07 AM
There is a common warning about excessive crimp on these bullets, but I think that is incorrect.
(https://i.postimg.cc/hvwb2JMr/blue135.jpg) (https://postimg.cc/RJ7HFZk6)
135 polymers
Post by: Inspector on April 11, 2021, 08:56:20 AM
I made these last week in hopes of finding a cheap alternative that shoots straight out of my glock.There is nothing wrong with your Glock. It shoots straight. It’s the shooter who’s cockeyed!!! :rofl: :rofl: :rofl:
There is a common warning about excessive crimp on these bullets, but I think that is incorrect.
(https://i.postimg.cc/hvwb2JMr/blue135.jpg) (https://postimg.cc/RJ7HFZk6)
135 polymers
Post by: oldfart on April 11, 2021, 09:06:14 AM
There is nothing wrong with your Glock. It shoots straight. It’s the shooter who’s cockeyed!!! :rofl: :rofl: :rofl:=============
sez the guy that just blamed his poor shooting on the iron sights on his carcano
Post by: Inspector on April 11, 2021, 09:10:34 AM
=============If you can’t see ‘em, you can’t use ‘em! :rofl:
sez the guy that just blamed his poor shooting on the iron sights on his carcano
Post by: oldfart on April 11, 2021, 09:19:24 AM
If you can’t see ‘em, you can’t use ‘em! :rofl:....
My ex-wife said that >:(
:rofl:
Post by: Inspector on April 11, 2021, 09:29:55 AM
....I know....
My ex-wife said that >:(
:rofl:
She told me! :rofl:
Post by: oldfart on April 11, 2021, 09:54:30 AM
I know....============
She told me! :rofl:
sorry, I have to go shoot off my blue balls now
(https://i.postimg.cc/nchK99qg/IMG-20210411-094034-2.jpg) (https://postimg.cc/0rhKLQW0)
Post by: Inspector on April 11, 2021, 10:38:14 AM
============Go have fun. My nephew came up from Chandler yesterday and we went to the range and shot his new Stribog Grand Power SP9A3. He had a suppressor on it as well. I liked the balance of it without the suppressor but it was very quiet with it. It is also a delayed roller blowback design. It was amazingly light recoiling. Felt no more than a 10/22. We shot some reloads of mine which were in the 950-1000 fps range so subsonic and he brought some 115gr aluminum cased supersonic rounds. Very interesting the difference in sound with the suppressor on between the two different cartridges. I also brought my S&W Model 547 which of course is quite old school. But was shot extensively by my nephew.
sorry, I have to go shoot off my blue balls now
(https://i.postimg.cc/nchK99qg/IMG-20210411-094034-2.jpg) (https://postimg.cc/0rhKLQW0)
This was the first time I had been to the range since late January.
Post by: stangzilla on April 12, 2021, 07:31:56 AM
the OAL just made it inside the cylinder of my 629. Ruger Redhawk and Super Blackhawk have slightly longer cylinder, but I plan to test it out of the 629 since Elmer Keith favored the S&W 29 I think
I made a heavy crimp so it shouldn't have any bullet jump, hopefully
test it out soon :thumbsup:
(https://live.staticflickr.com/65535/51111134518_694aee6a1c_b.jpg)
Post by: stangzilla on April 12, 2021, 11:14:00 AM
Well, for the past couple of weeks I've been reloading 38 and 45--about a .50 cal can of each. Ordered more bullets about 10 days ago but they haven't shown up yet.
Yesterday I saw 124 gr. JHP bullets (not heads or boolits) for sale at one of my suppliers, by the time lunch rolled around they were sold out.
I have noticed that pistol powder has been selling out quickly--no 231, BE, HP 38, tight group, etc., is available, just some Unique and trailboss. I have enough unique to last a few years, about enough to match my primer supply, lol.
Sent from my SM-G970U using Tapatalk
a few weeks ago at SEC I saw they are now selling Accurate powders. I guess since Hodgdon bought them. but they had a good amount of ACC#5, 7, and 9 a few weeks ago. might be gone by now
Post by: drck1000 on April 12, 2021, 11:29:54 AM
Post by: stangzilla on April 12, 2021, 04:25:12 PM
good thing I got the email from midway that they just got some in stock today, so I ordered 2 boxes of 500 LSWC 158 grain
I really like loading with LSWC in 357 and 44. a good all purpose round. or RNFP is good too. those just go well with revolvers, IMO :shaka:
Post by: stangzilla on April 12, 2021, 04:29:35 PM
with certain powders in my Hornady auto charge powder dispenser, it overcharges more than i would like it to
MK machining makes an insert that makes it not overcharge so much, its $14 for 3 of them of different sizes
but i did some online researching and found that someone used a expanding nut from Home Depot. its Everbilt expansion nut, #8-32 x 15/32 inches. good thing is on Home depot site it gave me the aisle number and bin number so was easy to find. didn't have to ask one of the workers that don't know shit either, so saved time by not consulting with them
we'll see how good it works
and was only 77 cents at home depot
update
I still get the overcharge with the ACC#7, so i tried the expanding nut and it worked great. but it goes so slow, i dont like slow
i can run the Hornady auto charge on the slow mode and it works fine, no overcharge and its not as slow as running it with the expanding nut. expanding nut basically slows down the trickle so it doesn't over charge. but so does running it on slow mode
i just thought i could run it on regular or fast mode with the expanding nut and it would work faster than running it on slow mode, but didn't work out that way
now I'll just run it on slow mode
oh well. live and learn. I'm only out 77 cents, so not so bad
Post by: stangzilla on April 16, 2021, 05:59:38 AM
Finish them today, hopefully
Just to see reliability using magnum primers in a non magnum pistol. G19, trigger is stock
Test them on the weekend
Post by: aletheuo137 on April 16, 2021, 07:04:45 AM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on April 18, 2021, 05:15:57 PM
Should be a blast :shaka:
Post by: stangzilla on April 19, 2021, 08:57:27 AM
45 acp 230 grains, 44 magnum 245 grains, 9mm 115 grains
45 and 9mm are factory ammo (brass looks dirty) , 44 is reloaded ammo (clean :D )
(https://live.staticflickr.com/65535/51125438862_956b451126_b.jpg)
Post by: stangzilla on April 23, 2021, 03:59:39 PM
(https://live.staticflickr.com/65535/51133581719_05f3843051_b.jpg)
Post by: stangzilla on April 26, 2021, 09:13:16 AM
i could go slightly hotter with the XTP bullets, and more hotter with the FTX bullets
even with 44 caliber seems the xtp is more accurate than the ftx, or could be i need to work up the load more
Post by: aletheuo137 on April 26, 2021, 02:04:44 PM
Sent from my SM-A102U using Tapatalk
Post by: drck1000 on April 26, 2021, 02:09:41 PM
Reload 9mm, thank you stangzilla!That's cute. . . a tribe of 50 ;D
SNIP
Just kidding. Good work! Let us know how they perform. :thumbsup:
Post by: stangzilla on April 26, 2021, 02:16:38 PM
Reload 9mm, thank you stangzilla!(https://uploads.tapatalk-cdn.com/20210427/533a6d1b2d5aef268c8e8beb28cc7701.jpg)
Sent from my SM-A102U using Tapatalk
:shaka:
Post by: aletheuo137 on April 26, 2021, 03:53:32 PM
That's cute. . . a tribe of 50 ;DHey! Be nice to the new guy, its 50 more than I had.
Just kidding. Good work! Let us know how they perform.
Sent from my SM-A102U using Tapatalk
Post by: drck1000 on April 26, 2021, 03:55:14 PM
Hey! Be nice to the new guy, its 50 more than I had.:rofl:
Sent from my SM-A102U using Tapatalk
That's 50 more than I've loaded for pistol, so I'd say you're good.
I just wanted to rib ya about it before the board Tourettes guy/girl/it chimed in. . . ;D
Post by: macsak on April 26, 2021, 04:13:13 PM
:rofl:
That's 50 more than I've loaded for pistol, so I'd say you're good.
I just wanted to rib ya about it before the board Tourettes guy/girl/it chimed in. . . ;D
heads
Post by: Kimo772 on April 26, 2021, 05:04:27 PM
I have load data and have collected:
- Lee 7.7 Japanese 3-die set
- New 7.7 brass (Priv)
- .311 caliber 180gr RN and 174gr spitzer bullets/heads/tips/projectiles (whatever folks wanna call them)
- CCI LRPs
- Powders include IMR3031, IMR and H4895, IMR4064, Varget, BL-c2, H4350
Still need a case trimmer...
Mahalo,
Kimo
Post by: aletheuo137 on April 26, 2021, 05:06:56 PM
:rofl:Well, I read what all of you post on reloading. Somethings are over my head but I've learned a few things reading your threads. Much appreciated despite the tourette's girl.
That's 50 more than I've loaded for pistol, so I'd say you're good.
I just wanted to rib ya about it before the board Tourettes guy/girl/it chimed in. . . ;D
Ps, how do you like your ribs?
Sent from my SM-A102U using Tapatalk
Post by: oldfart on April 26, 2021, 08:29:59 PM
Hey! Be nice to the new guy, its 50 more than I had....
Sent from my SM-A102U using Tapatalk
What's in that?
Post by: aletheuo137 on April 26, 2021, 08:58:53 PM
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on April 26, 2021, 09:28:53 PM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on April 27, 2021, 04:36:03 AM
Cci small pistol primers, 4.4 grains Titegroup, 115 grain speer cprn heads.
Sent from my SM-A102U using Tapatalk
Let us know how they shoot :shaka:
Post by: aletheuo137 on April 27, 2021, 06:29:53 AM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on April 27, 2021, 07:28:35 AM
I will when I have time. Right now I'm working two jobs besides helping a family member get thru a struggle. I'm reloading in the evening when I get home one or two steps at a time. That's why it's taking so long. I don't reload if I'm worn out or exhausted. Hence my little tribal group! But I'll let you know when I do get time....
Sent from my SM-A102U using Tapatalk
Yes, taking care of others is good.
Just don't forget to take care of yourself too.
You need balance.
Post by: aletheuo137 on April 27, 2021, 08:08:41 AM
...Yes sir! Especially reloading. It just seems to be a season of business right now, hopefully it'll be over by summer. Balance, we all need it
Yes, taking care of others is good.
Just don't forget to take care of yourself too.
You need balance.
Sent from my SM-A102U using Tapatalk
Post by: oldfart on April 27, 2021, 08:17:12 AM
Yes sir! Especially reloading. It just seems to be a season of business right now, hopefully it'll be over by summer. Balance, we all need it=========
Sent from my SM-A102U using Tapatalk
By "balance" I meant to go out and shoot something....for stress relief
It's high on my list of things to do on a regular basis.
It's therapeutic..
Post by: aletheuo137 on April 27, 2021, 09:01:28 AM
=========Yeah, mines would to be out in the woods! Something about being out in nature is relaxing and soothing. I'm long over due to shoot another pig. Lanai won't be till October.
By "balance" I meant to go out and shoot something....for stress relief
It's high on my list of things to do on a regular basis.
It's therapeutic..
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on May 03, 2021, 12:56:27 PM
I'd rather shoot Trailboss loads out of this 4 5/8" barrel SBH, or just not H110
this was my 1st 44mag revolver that I bought several years ago. grips are from ebay Arizona Custom grips
(https://live.staticflickr.com/65535/51156166086_326a5b6a7c_b.jpg)
Post by: oldfart on May 05, 2021, 06:22:07 AM
I read about reloaders on the mainland tossing out AMERC headstamp brass.
My coworker found some at the range here and picked them up.
They appear to be perfectly normal but when you reload them, they don't chamber.
Top photo is WCC brass which was reloaded about 3 times.
Bottom photo is an AMERC once-fired shell.
The load was a 230 gr. polymer coated round nose.
(https://i.postimg.cc/L4ZVKDm6/AMERCBRASS.jpg) (https://postimg.cc/9zC9yG4v)
It seems like the web portion is bloated and an ordinary (dillon) sizer die can't squeeze it down.
Perhaps a LEE FCD would bring it back down but I have not tried it yet.
The gauge pictured here is a MIDWAY chamber gauge.
I suspect for most guns, it will work ok. Normal pistol barrels aren't cut so tight.
Post by: stangzilla on May 10, 2021, 08:29:33 AM
(https://live.staticflickr.com/65535/51170972984_0b4a53176f_b.jpg)
Post by: stangzilla on May 26, 2021, 09:01:01 AM
i also have a data sheet that i made. (FPS is an estimate from the load data i'm getting off their website, chronograph is next on my list)
(https://live.staticflickr.com/65535/51200391097_9e0ac4fe28_b.jpg)
Post by: oldfart on May 26, 2021, 09:11:21 AM
Post by: stangzilla on May 26, 2021, 09:23:58 AM
Are those really Xtreme lead bullets?
yes, i got them a few years ago while they still shipped to hawaii.
Post by: oldfart on May 26, 2021, 10:50:31 AM
yes, i got them a few years ago while they still shipped to hawaii....
Xtreme was my favorite plated 9mm bullet :(
Post by: Lihikai on May 29, 2021, 01:32:16 PM
Been handloading for a while but getting my act together to start loading 7.7 Japanese for my Arisaka type 99. Anyone have experience or do's/dont's I need to know about before I start? YouTube has a lot of knuckleheads on it but I trust you guys and your advice always.
I have load data and have collected:
- Lee 7.7 Japanese 3-die set
- New 7.7 brass (Priv)
- .311 caliber 180gr RN and 174gr spitzer bullets/heads/tips/projectiles (whatever folks wanna call them)
- CCI LRPs
- Powders include IMR3031, IMR and H4895, IMR4064, Varget, BL-c2, H4350
Still need a case trimmer...
Mahalo,
Kimo
Post by: Kimo772 on May 30, 2021, 06:59:44 PM
Great recommendation on the Ed Harris "The Load" info/article. May try some of the reduced loads to preserve brass life.
Mahalo!
Kimo :shaka:
Post by: Lihikai on May 30, 2021, 08:47:04 PM
https://www.vkhgc.ca/documents/Ed%20gun%20cleaner.pdf
Post by: dogman on May 31, 2021, 09:52:37 PM
Post by: Glasser on June 01, 2021, 01:31:31 PM
Here's another good article from Ed for home made bore cleaner:
https://www.vkhgc.ca/documents/Ed%20gun%20cleaner.pdf
Interesting recipe. It's is not that far off from what is inside Kroil (ATF + acetone + other oilier lower flashpoint solvents).
(https://us-browse.startpage.com/av/anon-image?piurl=https%3A%2F%2Fimages-na.ssl-images-amazon.com%2Fimages%2FI%2F81%252BqLxuxHrL._AC_SL1500_.jpg&sp=1622590308T279a035d4369fe5ab0cd9b2759997996e89deb6c43e86af713eed7cf495e2323)
Post by: stangzilla on June 01, 2021, 06:42:32 PM
LRN, LSWC, and Montana Gold JHP. Getting ready for a new member of the family, S&W 686 coming very soon :geekdanc:
Post by: drck1000 on June 02, 2021, 10:52:16 AM
Reloaded some 357 magnumYou prob mentioned previously, but I either forget or didn't see. But is your 686 a plus (6 or 7 round)? 6" barrel?
LRN, LSWC, and Montana Gold JHP. Getting ready for a new member of the family, S&W 686 coming very soon :geekdanc:
I have a 686+ 6" barrel and it's been great. I love shooting that gun. Makes even .357 Mag seem pretty mild. Not that that is a high power or snappy round, but the heavier 6" barrel makes things super mellow (good for teaching context).
Post by: stangzilla on June 02, 2021, 12:22:59 PM
You prob mentioned previously, but I either forget or didn't see. But is your 686 a plus (6 or 7 round)? 6" barrel?
I have a 686+ 6" barrel and it's been great. I love shooting that gun. Makes even .357 Mag seem pretty mild. Not that that is a high power or snappy round, but the heavier 6" barrel makes things super mellow (good for teaching context).
I pick it up tomorrow
its the regular 6 rounds, 6" barrel. i already have a fiber optic front sight and a hogue bantam grip for it
I already have a 586, but not a 686. that's how i talked myself into buying the 686. :D
Post by: drck1000 on June 02, 2021, 12:30:11 PM
I pick it up tomorrowAwesome! My 686+ is my first revolver. It's one of my favorite revolvers to shoot.
its the regular 6 rounds, 6" barrel. i already have a fiber optic front sight and a hogue bantam grip for it
I already have a 586, but not a 686. that's how i talked myself into buying the 686. :D
Post by: oldfart on June 28, 2021, 09:32:47 AM
(https://i.postimg.cc/vZLWtybM/PHOTO-20210627-001626.jpg) (https://postimages.org/)
It is a Blue (obviously) 135 gr Truncated cone design, with CFE
Previous tests showed good results, so I made some more and tried them in different pistols.
The goal here was to create a practice load that simulates the feel of Federal 135 gr. HS ammo.
Federal 135 HS is advertised as 1060 fps
From my G17 this ammo clocked 1062 with an SD of 8. (this is really good)
Accuracy was pretty good at 25 yards. It printed 5 shots inside of 3 inches, which is typical for a Glock17.
Cost will depend if you can get primers or powder at reasonable prices.
"Pre-stupid" cost for this batch was $14 per 100 rounds.
If you want to duplicate this, I can give you the technical specs.
Post by: macsak on June 28, 2021, 12:27:17 PM
Actually I did this a few days ago and tested them for QC yesterday.
(https://i.postimg.cc/vZLWtybM/PHOTO-20210627-001626.jpg) (https://postimages.org/)
It is a Blue (obviously) 135 gr Truncated cone design, with CFE
Previous tests showed good results, so I made some more and tried them in different pistols.
The goal here was to create a practice load that simulates the feel of Federal 135 gr. HS ammo.
Federal 135 HS is advertised as 1060 fps
From my G17 this ammo clocked 1062 with an SD of 8. (this is really good)
Accuracy was pretty good at 25 yards. It printed 5 shots inside of 3 inches, which is typical for a Glock17.
Cost will depend if you can get primers or powder at reasonable prices.
"Pre-stupid" cost for this batch was $14 per 100 rounds.
If you want to duplicate this, I can give you the technical specs.
Post by: oldfart on June 28, 2021, 02:25:06 PM
fed sells a factory 135 gr round?.....
I heart google
https://www.federalpremium.com/handgun/premium-personal-defense/personal-defense-hydra-shok-low-recoil/11-PD9HS5+H.html
This stuff was selling for 30 bucks for 20 rounds.
>:(
Post by: macsak on June 28, 2021, 02:34:05 PM
.....
I heart google
https://www.federalpremium.com/handgun/premium-personal-defense/personal-defense-hydra-shok-low-recoil/11-PD9HS5+H.html
This stuff was selling for 30 bucks for 20 rounds.
>:(
Post by: ren on June 28, 2021, 08:12:49 PM
heads
(https://wmsmile.com/wp-content/uploads/2018/04/discolored.jpg)
Post by: oldfart on June 28, 2021, 08:15:55 PM
Post by: oldfart on July 25, 2021, 09:19:42 AM
...
Left...ammo for cops
Middle....ammo I made for me today
Right....ammo that HPD tells us to get
Post by: oldfart on July 28, 2021, 06:44:58 AM
I suspect that I seated too short.
Made up another test batch and replunked. Surprisingly, they all plunked at 1.12" which is the same length as speer Gdots.
It helps if your gauge is clean. They also plunked in the glock and BHP, both with match bbls.
Installed a new battery in the chrono this week so I'm planning to be testing on Saturday.
I might run some with unique just for fun.
(https://i.postimg.cc/QCpB4199/20210727-090311.jpg) (https://postimages.org/)
Post by: astroboy on July 28, 2021, 10:25:02 AM
I have not casted any bullets since 2005-2006. It took longer to find all of my casting
gear than to cast roughly 500 bullets. I may cast some bullets for my 44 and 45 pistols
when I find the molds.
Post by: oldfart on July 28, 2021, 10:43:30 AM
I fired up the lead pot and cast some 158 swc bullets from my new lee 6 cavity mold....
I have not casted any bullets since 2005-2006. It took longer to find all of my casting
gear than to cast roughly 500 bullets. I may cast some bullets for my 44 and 45 pistols
when I find the molds.
I like my Lee 6 cav molds. I run a pair of 45 cal so one cools while I crack the other.
It's my regular practice bullet.
Post by: stangzilla on July 29, 2021, 08:34:05 AM
They were in another cardboard box so I forgot I had them
Going to load it with some H110 :geekdanc:
Post by: oldfart on July 29, 2021, 08:44:10 AM
Found 250 Montana Gold 357 projectiles. 158 grain jhp===========
They were in another cardboard box so I forgot I had them
Going to load it with some H110 :geekdanc:
I run about 16.5 H110
Easily hits 1200+ even from a 3-1/2 in bbl.
(yeah Dogman, THAT 3-1/2 in bbl....the one you can't have LOL)
Post by: astroboy on July 29, 2021, 10:32:34 AM
...Ditto. The Lee 6 cavity molds work great. I have one for my .365 9x18 Makarov.
I like my Lee 6 cav molds. I run a pair of 45 cal so one cools while I crack the other.
It's my regular practice bullet.
I rarely shoot this pistol but the bullets from this mold cut nice clean holes in
paper and shoot better than the jacketed stuff.
Post by: macsak on July 29, 2021, 10:46:20 AM
===========
I run about 16.5 H110
Easily hits 1200+ even from a 3-1/2 in bbl.
(yeah Dogman, THAT 3-1/2 in bbl....the one you can't have LOL)
heads
Post by: dogman on July 29, 2021, 06:37:27 PM
===========:grrr: . . . . >:( . . . . . :'( . . . . . well mines 6-1/2 in ;D
I run about 16.5 H110
Easily hits 1200+ even from a 3-1/2 in bbl.
(yeah Dogman, THAT 3-1/2 in bbl....the one you can't have LOL)
Post by: macsak on July 29, 2021, 06:43:29 PM
:grrr: . . . . >:( . . . . . :'( . . . . . well mines 6-1/2 in ;D
HEADS
Post by: oldfart on July 29, 2021, 07:18:25 PM
:grrr: . . . . >:( . . . . . :'( . . . . . well mines 6-1/2 in ;D.....
Size doesn't matter, or so I've heard.
Is yours black?
Post by: dogman on July 29, 2021, 07:33:13 PM
.....Actually, the term they use is blued.
Size doesn't matter, or so I've heard.
Is yours black?
Post by: ren on July 29, 2021, 10:36:32 PM
Post by: Eric808 on July 30, 2021, 07:06:01 AM
Actually, the term they use is blued.
Is that the same as "blue balls?"
Post by: oldfart on July 30, 2021, 07:37:04 AM
Is that the same as "blue balls?"....
Here are my blue balls. But you know what they say....
"Once you go black, you don't go back"
(https://i.postimg.cc/nchK99qg/IMG-20210411-094034-2.jpg) (https://postimg.cc/0rhKLQW0)
Coincidentally, tomorrow is National Mutt Day.
Btw last sunday I tested my blue balls for accuracy and they shot a phenomenal cluster at 25 yds.
(https://i.postimg.cc/sgth31HG/20210726-091904.jpg) (https://postimages.org/)
Post by: dogman on July 30, 2021, 09:46:07 PM
Is that the same as "blue balls?"??? We are discussing revolver barrels, right?
Post by: oldfart on July 30, 2021, 10:25:55 PM
??? We are discussing revolver barrels, right?....
I forgot what we were supposed to be talking about.
Post by: dogman on July 31, 2021, 07:49:54 AM
What did you do in your reloading room today?
Post by: oldfart on July 31, 2021, 08:15:14 AM
Sorry, went off topic.===========
What did you do in your reloading room today?
sorted some brass for cleaning
I loaded up some RMR 124 mphp with 5.7 Unique and I WAS going to test them today until my daughter called me up and said her car was acting up so it looks like my weekend just got hosed.
Post by: drck1000 on July 31, 2021, 09:32:52 AM
Sorry, went off topic.Gotta get back into the flow of reloading. Gonna regroup on where I left off for .308 and take stock of what I have and what I need components wise. Will also start gearing up for reloading 9. That is once I get my power delivery. . . ;D
What did you do in your reloading room today?
Post by: macsak on July 31, 2021, 11:20:55 AM
Gotta get back into the flow of reloading. Gonna regroup on where I left off for .308 and take stock of what I have and what I need components wise. Will also start gearing up for reloading 9. That is once I get my power delivery. . . ;D
powder gives you power...
Post by: oldfart on July 31, 2021, 10:45:52 PM
Fixed my daughter's car. It was just the battery.
Stop by and say hello and clock your ammo.
If you're lucky, there might be cream puffs left.
Post by: drck1000 on August 01, 2021, 02:37:38 AM
powder gives you power...Or more poofs
Post by: stangzilla on August 02, 2021, 07:38:58 AM
(https://live.staticflickr.com/65535/51350872892_a663920b61_b.jpg)
Post by: oldfart on August 02, 2021, 07:50:23 AM
howz those everglades bullets?
Post by: stangzilla on August 02, 2021, 08:10:51 AM
nice
howz those everglades bullets?
those are actually Montana Gold bullets that i got from everglades ammo
but i have reloaded the everglades bullets before. they are pretty accurate and consistent. i'm going to order more everglades when they are in stock again
Post by: stangzilla on August 02, 2021, 08:13:01 AM
Post by: oldfart on August 02, 2021, 08:24:11 AM
the everglades bullets look exactly like MG bullets==========
oh...like costco batteries and Duracells
Post by: stangzilla on August 02, 2021, 08:35:16 AM
==========
oh...like costco batteries and Duracells
same-same :shaka:
Post by: dogman on August 03, 2021, 06:12:37 PM
the everglades bullets look exactly like MG bulletsAfter reading this I took another look at the 9mm 124 gr. FMJ brass bullets Rocky Mountain Reloading sells. They look the same as the Montana Gold 124 gr FMJ bullets. Maybe that explains why Montana Gold bullets are never in stock?
Post by: stangzilla on August 04, 2021, 07:39:34 AM
After reading this I took another look at the 9mm 124 gr. FMJ brass bullets Rocky Mountain Reloading sells. They look the same as the Montana Gold 124 gr FMJ bullets. Maybe that explains why Montana Gold bullets are never in stock?
i think i got some lead bullets from them pretty recently. good lead bullets.
Post by: drck1000 on August 04, 2021, 07:41:05 AM
i think i got some lead bullets from them pretty recently. good lead bullets.I gotta get going on my loading for 9 mm. I have a bunch of 9 mm boolits already. Xtreme, Everglades and I think one more.
Post by: macsak on August 04, 2021, 10:38:06 AM
I gotta get going on my loading for 9 mm. I have a bunch of 9 mm boolits already. Xtreme, Everglades and I think one more.
heads
Post by: oldfart on August 04, 2021, 11:24:21 AM
I gotta get going on my loading for 9 mm. I have a bunch of 9 mm boolits already. Xtreme, Everglades and I think one more.==========
This thread is "what did you DO in the reloading room"...
Not the, "What did I WANNA DO in the reloading room"
:rofl: :geekdanc: :shaka: :rofl:
Post by: macsak on August 04, 2021, 12:09:35 PM
==========
This thread is "what did you DO in the reloading room"...
Not the, "What did I WANNA DO in the reloading room"
:rofl: :geekdanc: :shaka: :rofl:
Post by: drck1000 on August 04, 2021, 12:15:04 PM
somepowda and power. . .idiotrahtard has his powda...
Post by: macsak on August 04, 2021, 12:22:39 PM
powda and power. . .
heads
Post by: drck1000 on August 05, 2021, 10:43:13 AM
heads#nopoofpoof
Post by: oldfart on August 17, 2021, 09:03:52 AM
This morning....just for fun
Post by: stangzilla on August 25, 2021, 12:29:53 PM
i guess the primer was stuck in the brass and hard time to push it out, so the decapping pin would get pushed out the backside of the die. its a safety measure in the Lee die that prevents the decapping pin from getting damaged it just gets pushed out before it gets bent or broken
never had this happen before. only had 4 rounds that this happened out of 50 rounds that i was reloading
i stopped after the first 2 primers got stuck and pushed out the depriming pin. did some research about what to do next. only thing i found, short of ordering a new die, was to superglue the decapping pin inside the screw inside the die
so i did that with gorilla glue, let it dry for 6 hours, tried it on those rounds, and same thing, stuck. but it did get the primers to move slightly but not completely removed
so i tightened down the pin screw again, this time it worked
i now have replacement decapping pins so if it happens again I'll try replace the pin. if that fails, i'll just order a new decapping die
could be my universal RCBS hand primer, bc it doesn't use any specific brass holder, its a spring loaded brass holder so it clamps to any caliber brass and sometimes it's not perfectly centered. that might be the culprit, i'll have to take a closer look next time. but i've used this hand primer several hundreds of times and never had a problem
could be Menehunes too. who knows? ;)
Post by: oldfart on August 25, 2021, 01:30:04 PM
Post by: Lihikai on August 25, 2021, 02:28:34 PM
Post by: stangzilla on August 25, 2021, 04:03:36 PM
degrease the pin and the collet?
did that, but still got pushed out
I keep a 3/4" open end and ½" box wrench next to my press to adjust the collet on Lee dies. If you have the collet really tight and the pin still rides up you can try roughing up the end of the pin with a file so that the collet will get a better bite on the pin.
ok, will try that next time if it gets pushed out again. thanks :shaka:
Post by: stangzilla on November 10, 2021, 11:38:25 AM
(https://live.staticflickr.com/65535/51671238479_8ee357d970_b.jpg)
Post by: macsak on November 10, 2021, 11:52:28 AM
will be first time loading wadcutters :geekdanc:
(https://live.staticflickr.com/65535/51671238479_8ee357d970_b.jpg)
Post by: drck1000 on November 10, 2021, 12:19:46 PM
headsBoolits!
Post by: macsak on November 10, 2021, 12:37:53 PM
Boolits!
Post by: drck1000 on November 10, 2021, 12:56:28 PM
free powda!more pewpew
or is it more amps?
:rofl:
Post by: oldfart on November 10, 2021, 01:37:27 PM
I don't see any lube in the grease grooves.
Is there a coating on the boolits?
$8 for 50 seems a bit high.
Post by: stangzilla on November 10, 2021, 02:40:06 PM
Uummmmm...
I don't see any lube in the grease grooves.
Is there a coating on the boolits?
$8 for 50 seems a bit high.
yeah a bit high. last minute buy as i was cashing out at WGS, I saw those WC sitting on the counter and decided to give them a try
no lube. i got some lube coming in the mail. i realized that when i got home, no lube. but thats ok. first time lubing too. :shaka:
Post by: oldfart on November 10, 2021, 04:42:23 PM
yeah a bit high. last minute buy as i was cashing out at WGS, I saw those WC sitting on the counter and decided to give them a try....
no lube. i got some lube coming in the mail. i realized that when i got home, no lube. but thats ok. first time lubing too. :shaka:
Check the diameter?
I could size and lube at my house.
100 boolits would take less than 10 minutes.
Then spend the rest of the time smoking fine cigars and drinking beer.
Fyi, sometimes they are more accurate unsized as long as the diameter is pretty close.
Post by: stangzilla on November 10, 2021, 04:53:53 PM
....
Check the diameter?
I could size and lube at my house.
100 boolits would take less than 10 minutes.
Then spend the rest of the time smoking fine cigars and drinking beer.
Fyi, sometimes they are more accurate unsized as long as the diameter is pretty close.
i have not checked the diameter yet. i'll check it tonight if i remember
Post by: macsak on November 10, 2021, 05:24:50 PM
yeah a bit high. last minute buy as i was cashing out at WGS, I saw those WC sitting on the counter and decided to give them a try
no lube. i got some lube coming in the mail. i realized that when i got home, no lube. but thats ok. first time lubing too. :shaka:
use spit...
Post by: oldfart on November 10, 2021, 05:33:53 PM
use spit.......
Heads
Post by: stangzilla on November 10, 2021, 07:04:54 PM
use spit...
What I always say, "if no fit, add some spit" :shaka:
Post by: mrgaf on November 10, 2021, 08:12:03 PM
Post by: aletheuo137 on November 11, 2021, 08:02:20 AM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on November 11, 2021, 08:11:18 AM
:rofl:
Post by: aletheuo137 on November 11, 2021, 08:18:18 AM
That's the gun that that had a trigger job, then no can go boom boom?Yes sir! Never thought I had to be my own gunsmith!
:rofl:
Saliva - Click Click Boom
https://youtu.be/YfjTZLxekig
Sent from my SM-A102U using Tapatalk
Post by: Inspector on November 11, 2021, 08:20:49 AM
Case prep on 9mm, 38SPL and 380ACP.
Load 200 rounds of 9mm.
Post by: ren on November 11, 2021, 08:50:24 AM
Yes sir! Never thought I had to be my own gunsmith!
Saliva - Click Click Boom
https://youtu.be/YfjTZLxekig
Sent from my SM-A102U using Tapatalk
All this time I thought it was Fred Durst and Limpbizkit
Post by: stangzilla on November 11, 2021, 09:05:10 AM
....
Check the diameter?
I could size and lube at my house.
100 boolits would take less than 10 minutes.
Then spend the rest of the time smoking fine cigars and drinking beer.
Fyi, sometimes they are more accurate unsized as long as the diameter is pretty close.
Those wadcutters are .358"
I'm going to reload a few and see how they fit in the cylinder before I do the rest. If not too tight I think I'll be ok not resizing them. If I need to resize, probably too much hassle. I just give um to you :shaka:
Post by: oldfart on November 11, 2021, 09:22:23 AM
Those wadcutters are .358"=========
I'm going to reload a few and see how they fit in the cylinder before I do the rest. If not too tight I think I'll be ok not resizing them. If I need to resize, probably too much hassle. I just give um to you :shaka:
what lube you got?
no use spit :rofl:
Post by: stangzilla on November 11, 2021, 09:46:32 AM
=========
what lube you got?
no use spit :rofl:
I have the Lee liquid alox
Post by: oldfart on November 11, 2021, 10:56:07 AM
I have the Lee liquid alox....
No need size.
Post by: stangzilla on November 11, 2021, 11:33:41 AM
....
No need size.
Ok. Thanks :shaka:
Post by: aletheuo137 on November 11, 2021, 05:09:28 PM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on November 12, 2021, 07:00:33 AM
270 is a fine cartridge.
Post by: aletheuo137 on November 12, 2021, 07:19:25 PM
Sent from my SM-A102U using Tapatalk
Post by: dogman on November 12, 2021, 07:46:57 PM
Post by: macsak on November 12, 2021, 08:15:11 PM
Loaded 300 rounds 9mm after work today, will unload 300 rounds of 9mm on Sunday, weather permitting.
heads
Post by: dogman on November 12, 2021, 08:18:33 PM
headsCase Heads? Thanks for the brass delivery. :thumbsup:
Post by: macsak on November 12, 2021, 08:20:58 PM
Case Heads? Thanks for the brass delivery. :thumbsup:
thanks for showing me all the toys...
Post by: drck1000 on November 12, 2021, 08:29:57 PM
Loaded 300 rounds 9mm after work today, will unload 300 rounds of 9mm on Sunday, weather permitting.It needs to be permitting weather to shoot some 9 mm? :P ;D
Post by: dogman on November 12, 2021, 08:39:26 PM
It needs to be permitting weather to shoot some 9 mm? :P ;DNot more than six inches of rain, more than that and I am wimping out. :-[
Post by: stangzilla on November 12, 2021, 08:53:21 PM
Lubed some heads
Post by: drck1000 on November 12, 2021, 08:53:45 PM
Not more than six inches of rain, more than that and I am wimping out. :-[Ready to load up some 6.5 CM soon?
Post by: dogman on November 12, 2021, 08:56:36 PM
Ready to load up some 6.5 CM soon?Done
Post by: drck1000 on November 12, 2021, 09:10:28 PM
DoneI have pretty much everything. Just waiting on the expander mandrel. Oh, and the rifle itself :'(
Should hopefully be done in the next few weeks.
Post by: dogman on November 12, 2021, 09:16:12 PM
I have pretty much everything. Just waiting on the expander mandrel.I'm not that advanced.
Post by: Inspector on November 13, 2021, 03:21:15 AM
I have pretty much everything. Just waiting on the expander mandrel. Oh, and the rifle itself :'(I’m not advanced either.
Should hopefully be done in the next few weeks.
Post by: Inspector on November 13, 2021, 03:54:20 AM
Yesterday I prepped a bunch of 9mm cases and loaded 100 rounds of 9mm. Also did some general maintenance on my dies and presses. And general housekeeping around my garage. I recently bought a little air compressor and while it is totally inadequate for running tools it works well for blowing out dies and inflating tires.
Earlier this week I walked into one of the LGS here and they had 3lbs of CFE Pistol and 1lb of Titegroup. They let me buy them all so I think I now have enough powder along with what I already had to last me for quite a while.
My Ruger Super Redhawk sold on consignment so I am looking for my next EDC pistol since my Glock 17 and Sig P228 have turned out to be way too big and heavy for EDC.
Post by: stangzilla on November 22, 2021, 11:06:07 AM
got some wadcutters in 148 grain 357 and 200 grain 44 :geekdanc:
(https://live.staticflickr.com/65535/51698906934_047a724c59_b.jpg)
Post by: macsak on November 22, 2021, 11:22:52 AM
(https://live.staticflickr.com/65535/51698508438_5754ba9a22_b.jpg)
got some wadcutters in 148 grain 357 and 200 grain 44 :geekdanc:
(https://live.staticflickr.com/65535/51698906934_047a724c59_b.jpg)
Post by: stangzilla on November 30, 2021, 02:28:00 PM
by the book, load seems rather low. but I'm going by the book. we'll see how it shoots
up next will be the 44 DEWC. I haven't found any load data for that particular projectile, so we'll have to start low and work it up from there
Post by: aletheuo137 on December 01, 2021, 08:21:22 PM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on December 02, 2021, 06:40:48 AM
Rebuild rifle and pistol frames!(https://uploads.tapatalk-cdn.com/20211202/12b6b03bcbf3c3affbfe905abe00f255.jpg)....
Sent from my SM-A102U using Tapatalk
Looks like you got a bad termite problem there.
Try Pestech Exterminators. :rofl:
Post by: Inspector on December 02, 2021, 08:19:45 AM
Rebuild rifle and pistol frames!(https://uploads.tapatalk-cdn.com/20211202/12b6b03bcbf3c3affbfe905abe00f255.jpg)Looks like worm wood to me! :rofl:
Sent from my SM-A102U using Tapatalk
Post by: Flapp_Jackson on December 02, 2021, 09:52:20 AM
Looks like worm wood to me! :rofl:
I was going to ask why so many screw holes?
Ooops! :rofl:
Post by: QUIETShooter on December 02, 2021, 01:39:40 PM
I was going to ask why so many screw holes?
Ooops! :rofl:
My target frames look like that. :rofl:
My wife suddenly became a smart ass when she said "I thought you are supposed to hit the round circle in the center....."
:grrr: Made me feel just wonderful.......
Post by: aletheuo137 on December 02, 2021, 05:42:38 PM
Sent from my SM-A102U using Tapatalk
Post by: ren on December 02, 2021, 06:34:40 PM
Taking alot of people shooting lately, they want to get into shooting. I had the frames a long time. Besides, I'm a bad shot. Can't hit the side of a barn!
Sent from my SM-A102U using Tapatalk
bring a bigger barn
Post by: Inspector on December 12, 2021, 10:53:05 AM
I got all the components together to reload 3-400 rounds of 38 Special today. As I was setting up the first 200 cases I noticed numerous 357 cases were mixed in with my 38 cases. Looks like when I was prepping 357 cases sometime during the summer I dumped them in with my 38 Special cases by accident. So I got to spend the next half hour or so sorting out brass. I decided to only load 200 rounds today due to this.
I went through all my ammo boxes and realized I don’t have enough for my 38 Special and 357 magnum so I’ll go down to the store later today and get some. I want to expand the amount of 38 Special and 357 ammo I keep in inventory.
I organized the ammo boxes I do have and labeled them and did the data input into my app.
Post by: wirecounter on December 14, 2021, 03:14:30 PM
Post by: Inspector on December 14, 2021, 03:40:26 PM
Absolutely nothing!I wanted to load my last 100 rounds of 38 Special today. I ended up with only 94 cases so I went out to my garage where I had 20 cases that needed to be prepped. So I prepped them in order to have an even 100 to load. I finished that up and cleaned my gun from shooting this morning. I prepped a bunch of 357 Magnum cases. I organized my closet with all my ammo boxes.
I still have ~300 cases of 9mm to prep and 50 cases of 7.62x38R to prep and load.
Post by: Inspector on December 18, 2021, 02:34:39 PM
I retrieved 200 rounds of 357 Magnum cases from my tumbler with walnut shells and blew out the primer holes with compressed air. I organized and labeled my boxes and entered them into my inventory app. I placed all the cases in my loading blocks and hand primed all of them with regular SPP as they are all going to be bunny fart loads. I set up my press and powder measure for the Trail Boss powder. And I retrieved 500 heads (DG 158gr SWC Powder Coated) from my inventory for loading tomorrow. I took inventory of all of the different heads I have for 357 magnum and I realized I am getting low so I need to order more or make more. Right now prices are relatively low on lead heads still so I think I’ll order them and save my casting lead for more lean times.
Post by: drck1000 on December 18, 2021, 02:41:29 PM
My target frames look like that. :rofl:Sounds like the joke could be on her, in your choice of targets to hit :P
My wife suddenly became a smart ass when she said "I thought you are supposed to hit the round circle in the center....."
:grrr: Made me feel just wonderful.......
Post by: Inspector on December 20, 2021, 02:48:16 AM
I loaded another 100 rounds of 357 Magnum.
I just started using the 38/357 LSWC PC boolits I bought from DG Bullets. I am not too happy with the powder coating on this batch. And I was happy with the last batch of boolits I bought from Summit City. BTW, Summit City has a 5% off for returning customers and 15% off for X-Mas Sale right now.So far their CS has been very good and their bullets have been good as well. Here is the URL:
https://summitcitybullets.com/
They ship USPS so I imagine they will ship to Hawaii.
Post by: oldfart on December 20, 2021, 06:22:21 AM
Post by: Inspector on December 20, 2021, 06:37:16 AM
What you putting under the 357 coated bullets?Depends but yesterday was Unique. I have been using Trail Boss for the bunny farts and H110 with magnum primers for the heavy loads. But the heavy loads I have been using FMJ bullets. The LSWC Powder Coated boolits shoot very nicely under Unique and the recoil is moderate.
Post by: oldfart on December 20, 2021, 08:50:41 AM
Depends but yesterday was Unique. I have been using Trail Boss for the bunny farts and H110 with magnum primers for the heavy loads. But the heavy loads I have been using FMJ bullets. The LSWC Powder Coated boolits shoot very nicely under Unique and the recoil is moderate.===========
I used to run lubed lead 158 swc with 14.5 H110.
It has a nice thump without shaking the false teeth out of your mouth.
I know we can push the coated bullets harder, but I don't drive my Nissan at 80 mph all the time either.
Post by: Inspector on December 20, 2021, 09:03:13 AM
===========Cool! I’ll load a few of those today. I’m planning to go to the range tomorrow with the powder coated boolits.
I used to run lubed lead 158 swc with 14.5 H110.
It has a nice thump without shaking the false teeth out of your mouth.
I know we can push the coated bullets harder, but I don't drive my Nissan at 80 mph all the time either.
Today I’m loading another 100 rounds of 357 Magnum but without the magnum. Using Trail Boss on these.
I finished up all my case prep for today. Tomorrow I do inventory on all my once fired brass and start planning for increasing my ammo stores. I need to buy more heads.
Post by: oldfart on December 22, 2021, 08:57:06 AM
(https://i.postimg.cc/P5d0h43w/Blueballs.jpg) (https://postimages.org/)
Post by: Inspector on December 22, 2021, 09:03:27 AM
I'm gifting blue balls to some coworkers for Christmas.N I C E ! ! !
(https://i.postimg.cc/P5d0h43w/Blueballs.jpg) (https://postimages.org/)
Post by: stangzilla on December 22, 2021, 09:06:22 AM
I'm gifting blue balls to some coworkers for Christmas.
(https://i.postimg.cc/P5d0h43w/Blueballs.jpg) (https://postimages.org/)
much better than candy canes :thumbsup:
Post by: oldfart on December 22, 2021, 09:14:35 AM
Who makes green coated bullets?
I'm all about celebrating stuff.
Post by: Inspector on December 22, 2021, 09:18:51 AM
Next year I'll look for green balls. Red is common.DG (Dang Good) Bullets does the green.
Who makes green coated bullets?
I'm all about celebrating stuff.
Post by: oldfart on December 22, 2021, 09:44:43 AM
DG (Dang Good) Bullets does the green.===========
and SNS does a nice red!
'tis the season!
Post by: Inspector on December 23, 2021, 09:02:40 AM
===========Summit City and Acme does red as well. But I would say the Summit City boolits are a more festive (Brighter) red than Acme.
and SNS does a nice red!
'tis the season!
Post by: oldfart on December 23, 2021, 09:38:58 AM
Summit City and Acme does red as well. But I would say the Summit City boolits are a more festive (Brighter) red than Acme.===========
sns are really bright red
hohoho
Post by: Inspector on December 23, 2021, 11:47:57 AM
===========I just order 2k 158gr 38/357 from Summit City. They gave me 5% off for being a repeat customer and another 15% off for their X-Mas Sale.
sns are really bright red
hohoho
Merry Christmas to me! HoHoHo
Post by: oldfart on December 23, 2021, 01:15:59 PM
next year will be red rockets
Post by: Inspector on December 23, 2021, 01:19:09 PM
this year it's blue ballshttps://youtu.be/9slgiOD0VAk
next year will be red rockets
Post by: oldfart on December 23, 2021, 01:29:49 PM
Post by: aletheuo137 on December 24, 2021, 03:54:56 PM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on December 25, 2021, 06:44:40 PM
Post by: dogman on December 25, 2021, 07:51:39 PM
I seem to notice Duracell and Kirkland are repeat offenders in the leakage department.I read Duracell makes the batteries for Kirkland.
Post by: ren on December 25, 2021, 08:05:46 PM
got most parts in now assembly. Problem I am having is the plumbing leaks from the 1/8" copper tubing to the rest of the tubes. I'm trying to find a suitable adaptor / solution to fit a 5/8 tube to a the 1/8" copper tube coil. I know resistance increases from larger diameter to smaller. Going to try soldering a bigger tube to the smaller tube or try a barbed connector / reducre with small hose clamps. Any ideas?
Post by: Inspector on December 26, 2021, 01:29:33 AM
I seem to notice Duracell and Kirkland are repeat offenders in the leakage department.I have noticed the same. I gave up on buying my batteries at Costco for that reason.
Post by: Inspector on January 19, 2022, 03:33:33 AM
I have noticed the same. I gave up on buying my batteries at Costco for that reason.BTW, I have changed my attitude towards the battery leakage issue. So I can go back to buying my batteries at Costco if I want to. But now I am near a Harbor Freight and they sell similar batteries very cheap. And they put them on sale even cheaper on a regular basis.
What I did last year is on New Years Day I went through my house and made a complete list of all things that use a battery. I noted the size and quantity of batteries in each device. I also removed the batteries out of the devices I knew I was not planning on using in the near future. So I preempted the leakage issue. I also decided which items I was going to replace the batteries in every New Years Day. So last year I bought a bunch of batteries and replaced them in every smoke detector, carbon monoxide detector, remote controls, clocks, backup batteries for plug in clocks, gun safe, red dot sights, etc. I also bought new backup batteries for my lanterns in case SHTF and in my weather radio. I will replace these backups every 2 years. And I also have extras for those items that need new batteries before the year is up. So initially it cost a pretty penny upfront to do this, but I had quite a few extras left over from my initial purchase a year ago that I didn’t have to replenish many batteries this year.
The big thing for me is that I had leakage in my gun safe and it took a lot effort to save the battery box. So now I don’t have to worry about it if I keep up my routine. Also, I had to throw away some good tools that the batteries leaked in an ruined. And I no longer have to deal with a smoke alarm that is designed to only go off at 2am when the batteries die. :rofl:
Post by: Inspector on January 19, 2022, 03:45:59 AM
Yesterday I finished prepping 300 rounds of 9mm cases. I have 200 left to tumble. I will start reloading these later this week. Also I started washing 400 rounds of 380ACP out of my goal of 700 to add. I bought a bunch of really dirty range brass so I am decapping them and washing them before I run them through my sizing die. I started to run out of ultrasonic cleaner so I went to some of my LGS and they are all out. So I ordered some online. I also did some reorganizing of my ammo supply. I also did a lot of labeling.
Post by: stangzilla on January 21, 2022, 10:36:23 AM
(https://live.staticflickr.com/65535/51833396664_7e09b3fdbc_z.jpg)
Post by: Inspector on January 21, 2022, 10:41:38 AM
44 magnum lead loads. snake food. 245 grain SWC, 200 grain WC :thumbsup:Nice! :thumbsup:
(https://live.staticflickr.com/65535/51833396664_7e09b3fdbc_z.jpg)
Post by: Inspector on January 21, 2022, 10:46:02 AM
I also finished prepping the last 100 of 9mm cases. And I loaded 100 rounds of 9mm using 124gr X-Treme CPRN with Titegroup and SPP.
Post by: Inspector on January 22, 2022, 11:34:28 AM
I also took delivery of a case of Federal Small Pistol Primers.
Post by: stangzilla on January 22, 2022, 02:03:17 PM
Also got in the mail 500 rounds of 158 grain JSP projectiles from Everglades Ammo
Post by: macsak on January 22, 2022, 09:24:23 PM
I pre-prepped some cases by unloading them at kokohead this morning ;)
Also got in the mail 500 rounds of 158 grain JSP projectiles from Everglades Ammo
heads
Post by: aletheuo137 on January 23, 2022, 07:30:01 AM
headsReloading vs unloading! They go together!
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on February 11, 2022, 07:55:48 AM
I think the same load I did last time will work fine, but gotta shoot it first and see. load is right at the max recommended for this projectile and titegroup. no need to go any more than that. as long as its accurate, I'll leave it there bc it's kind of a soft load even at the max charge. if not i'll back off a bit and see if its better
Post by: macsak on February 11, 2022, 12:02:39 PM
Post by: stangzilla on February 11, 2022, 12:40:10 PM
"a friend" got notice of a "partial shipment" of an order of "heads" that was placed on "black friday"...
heads
Post by: aletheuo137 on February 11, 2022, 07:33:26 PM
headsblack friday
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on February 18, 2022, 10:53:15 AM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on February 18, 2022, 01:42:57 PM
Using up the .358 WC I got from WGS
Now I charge the cases and finish them
Post by: macsak on February 18, 2022, 03:52:10 PM
Lubed some heads
Using up the .358 WC I got from WGS
Now I charge the cases and finish them
lube
Post by: stangzilla on February 18, 2022, 05:55:55 PM
Will test in it's intended handgun, my 627 PC snubnose tomorrow. Low recoil, quick f/u shots
Should be similar results in my short barrel GP100 Wiley Clapp
Post by: bushmasta55 on February 19, 2022, 04:26:13 PM
Post by: ren on February 19, 2022, 04:39:38 PM
About to prep some 556 LC brass also got in some SMK 77 grain .224 heads, maybe will try to clone the MK262 round. Anyone tried this before? I know Johnny's Reloading Bench channel on youtube did a bunch of videos on it.
difficult to get the velocities with commercial powders. I clocked them going 2900 fps. I tried ARCOMP, RL15 and Varget up to 2700 ~ 2750. It gets pretty hot after that - primers going flat
Post by: bushmasta55 on February 19, 2022, 09:21:52 PM
difficult to get the velocities with commercial powders. I clocked them going 2900 fps. I tried ARCOMP, RL15 and Varget up to 2700 ~ 2750. It gets pretty hot after that - primers going flat
That is true even Johnny had a difficult time getting the same velocities, but I think the powder used in the factory loads are blended. I have the sierra reloading manual and will reloading around to that. Currently I have only Varget on hand for powers. What would be a middle load for Varget?
Post by: ren on February 19, 2022, 09:56:11 PM
Post by: aletheuo137 on February 21, 2022, 07:29:43 AM
Prep cases, clean, trim, lubed, debur.
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on February 21, 2022, 11:59:52 AM
Sent from my SM-A102U using Tapatalk
Post by: drck1000 on February 21, 2022, 04:59:11 PM
(https://uploads.tapatalk-cdn.com/20220221/a633d1d4cb659878354c95a75ca0beb6.jpg)What kind of brass is that? Looks like steel case or coated. Or very dirty.
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on February 21, 2022, 07:17:19 PM
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on February 25, 2022, 05:05:10 PM
Sent from my SM-A102U using Tapatalk
Post by: ren on February 25, 2022, 05:55:37 PM
Dies & bulletheadsarrived today!
Sent from my SM-A102U using Tapatalk
Post by: dogman on February 25, 2022, 07:28:53 PM
Post by: macsak on February 25, 2022, 07:37:54 PM
ordered 3300 + 500 on black friday
needed to spend $300 to get 15% off instead of 10%, so bought the extra 500
the first 500 arrived a week or so ago
so total shipment time was just under 3 months
Post by: aletheuo137 on February 26, 2022, 04:02:12 PM
"Heads" are on the case.Also a term used by mac every now and then!
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on March 06, 2022, 06:31:46 PM
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on March 12, 2022, 09:18:27 AM
Sent from my SM-A102U using Tapatalk
Post by: Rhed on March 12, 2022, 09:52:43 PM
(https://imagizer.imageshack.com/v2/1024x768q90/924/CWO1an.jpg) (https://imageshack.com/i/poCWO1anj)
Loaded up some 223 77 grainers for some fun shoot down the 50 with my son tomorrow. Gonna bring out probably DDM4V7 and maybe Tavor or mr556.
Post by: aletheuo137 on March 13, 2022, 07:19:02 PM
Sent from my SM-A102U using Tapatalk
Post by: bushmasta55 on March 13, 2022, 09:42:19 PM
(https://imagizer.imageshack.com/v2/1024x768q90/924/CWO1an.jpg) (https://imageshack.com/i/poCWO1anj)
Loaded up some 223 77 grainers for some fun shoot down the 50 with my son tomorrow. Gonna bring out probably DDM4V7 and maybe Tavor or mr556.
What heads are you using ?
Post by: Rhed on March 13, 2022, 11:26:13 PM
What heads are you using ?
Nosler custom competition factory seconds from SPS. Got them awhile back before covid. They used to carry them by box of 1000. Now, when they go on sale and in stock, is per bag of 100. Though, these are pretty accurate and very stable. Shot targets up to 700 consistent with these. Not bad at all. I also used Sierra TMK out these distance. And the factory seconds shoots just as good for the price. https://www.shootersproshop.com/22-caliber-77gr-hpbt-custom-competition-100ct-blem.html
Post by: oldfart on March 20, 2022, 05:39:24 AM
ordered some bullets to make me happy :)
Post by: aletheuo137 on March 26, 2022, 07:51:04 AM
Sent from my SM-A102U using Tapatalk
Post by: macsak on March 26, 2022, 09:00:35 PM
(https://i.postimg.cc/qMHfvrsv/smiley.jpg) (https://postimages.org/)
ordered some bullets to make me happy :)
Post by: aletheuo137 on March 26, 2022, 09:03:45 PM
headsYou should have that tick looked at!
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on March 28, 2022, 08:03:45 AM
(https://live.staticflickr.com/65535/51966531110_468a4a1fc7_z.jpg)
Post by: drck1000 on March 28, 2022, 09:04:35 AM
240 grain XTP's 44 magnum"to you feel lucky?"
Very nice. I'm going to have to get loading on 9 mm. Just picked up a PCC. . . :geekdanc:
That's going to make ammo usage rate increase.
Post by: stangzilla on March 29, 2022, 12:13:05 PM
"to you feel lucky?"
Very nice. I'm going to have to get loading on 9 mm. Just picked up a PCC. . . :geekdanc:
That's going to make ammo usage rate increase.
the reason I love to shoot 44 magnum is bc of Dirty Harry
all while eating a hot dog
https://www.youtube.com/watch?v=38mE6ba3qj8
"go ahead. make my day"
"we aren't going to let you walk out of here"
"who's we, sucka?"
"Smith & Wesson, & me"
https://www.youtube.com/watch?v=RSAyz5c3JmM
Post by: Flapp_Jackson on March 29, 2022, 12:35:56 PM
the reason I love to shoot 44 magnum is bc of Dirty Harry
all while eating a hot dog
"go ahead. make my day"
"we aren't going to let you walk out of here"
"who's we, sucka?"
"Smith & Wesson, & me"
... and taking a load of buckshot to the leg!
Post by: aletheuo137 on March 29, 2022, 01:51:47 PM
Sent from my SM-A102U using Tapatalk
Post by: drck1000 on March 29, 2022, 01:58:07 PM
Setting aside range 9mm ammo for CMO's big day!bazinga :geekdanc: :shaka: :rofl:
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on April 01, 2022, 05:38:08 AM
Sent from my SM-A102U using Tapatalk
Post by: oldfart on April 10, 2022, 06:59:54 PM
Stopping work seems to be a lot of work.
carry on gents
Post by: aletheuo137 on April 11, 2022, 08:17:02 AM
Nothing...taking a hiatus from shooting while getting ready to retire.I'm still 5 years out from retirement. I have a friend who retired a couple of years ago and now contemplating going back to work to fund some projects! Vicious cycle
Stopping work seems to be a lot of work.
carry on gents
Sent from my SM-A102U using Tapatalk
Post by: oldfart on April 11, 2022, 10:33:35 AM
I'm still 5 years out from retirement. I have a friend who retired a couple of years ago and now contemplating going back to work to fund some projects! Vicious cycle=============
Sent from my SM-A102U using Tapatalk
Here is a tip...
start learning about social security and medicare early on. Before 64 or 65.
I'm planning on continuing to work on an important project that I started about 16 years ago but never finished.
It will be part-time work after retirement.
Post by: drck1000 on April 11, 2022, 01:49:44 PM
Loaded some 260 rem to sight in rifle. Wind adds a challenge.Did you shoot those 260 rem?
Sent from my SM-A102U using Tapatalk
I shot some 6.5 CM on Saturday. It was quite breezy at times. Still in barrel speed up, so mostly just getting data, but all good practice.
Hopefully I'll get into the groove of loading and shooting between my .308 and 6.5 CM. Then mix in loading for 9 mm soon. If my request for brass ever gets attention (from the person I've been texting). . . (kidding, kidding)
Post by: aletheuo137 on April 11, 2022, 02:12:19 PM
Did you shoot those 260 rem?Couldn't get a table and wind was an issue! I didn't want to rush it. I'm going to try again when I get some time off, maybe Friday.
I shot some 6.5 CM on Saturday. It was quite breezy at times. Still in barrel speed up, so mostly just getting data, but all good practice.
Hopefully I'll get into the groove of loading and shooting between my .308 and 6.5 CM. Then mix in loading for 9 mm soon. If my request for brass ever gets attention (from the person I've been texting). . . (kidding, kidding)
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on April 18, 2022, 02:04:53 PM
ordered some FTX projectiles in 357 and 44 for more H110 powder loads
Post by: aletheuo137 on April 20, 2022, 05:41:32 PM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on April 27, 2022, 07:46:12 AM
Post by: macsak on April 27, 2022, 08:27:47 AM
(https://live.staticflickr.com/65535/52032004832_d5686ccc2e_z.jpg)
Post by: stangzilla on May 02, 2022, 08:14:33 AM
(https://live.staticflickr.com/65535/52044407029_0ce0911850_z.jpg)
heads
Post by: drck1000 on May 02, 2022, 08:38:25 AM
SNIPThat second photo looks like the "Terminator" with the red eyes.
heads
#illbebahhhck
Post by: stangzilla on May 02, 2022, 04:20:01 PM
That second photo looks like the "Terminator" with the red eyes.
#illbebahhhck
I call these my Bigfoot loads
the polymer tips prevent the Bigfoot hair from getting stuck in the hollow point bullet :shaka:
Post by: stangzilla on May 23, 2022, 09:42:21 AM
next I'll be loading some 44magnum 180 grain XTP with H110. should be some higher velocity loads
Post by: stangzilla on June 01, 2022, 04:01:14 PM
(https://live.staticflickr.com/65535/52104687135_8966825d0d_c.jpg)
first time loading 180 grain XTP's. more powder in these than in the 225 or 240 grain bullets. makes for some nice fireball action :geekdanc:
(https://live.staticflickr.com/65535/52110592323_aa933f300f_c.jpg)
Post by: 808Hunta on June 08, 2022, 08:23:02 PM
Post by: stangzilla on June 13, 2022, 01:58:36 PM
Post by: drck1000 on June 13, 2022, 02:02:29 PM
Getting ready for lana'i6.5x284 Norma, very nice! Where's the gun? ;D
Post by: 808Hunta on June 13, 2022, 08:37:45 PM
Post by: stangzilla on June 17, 2022, 03:09:09 PM
(https://live.staticflickr.com/65535/52152846876_f381c0d010_c.jpg)
Post by: Rhed on June 27, 2022, 10:38:32 PM
(https://imagizer.imageshack.com/v2/1024x768q90/922/1jvYVR.jpg) (https://imageshack.com/i/pm1jvYVRj)
(https://imagizer.imageshack.com/v2/1024x768q90/924/32VE7J.jpg) (https://imageshack.com/i/po32VE7Jj)
Post by: stangzilla on July 05, 2022, 05:46:54 PM
(https://live.staticflickr.com/65535/52195996467_5406f6bf60_c.jpg)
Post by: oldfart on July 16, 2022, 08:52:59 PM
(https://i.postimg.cc/qMHfvrsv/smiley.jpg) (https://postimages.org/)===========
ordered some bullets to make me happy :)
I started testing these bullets.
They are pretty good.
With my compact SW 9mm SD pistol it groups about 3 inches at 25 yds.
(https://i.postimg.cc/25H10DK6/20220716-194239.jpg) (https://postimg.cc/947XfvV5)
These are actually made for 38/357 pistols but it works ok in a 9mm.
It's a 147 gr truncated cone design.
The long bearing surface and large diameter contributes to accuracy.
The downside is that it bulges the tapered 9mm case so it may not feed in tight chambered pistols.
I would never use these for home defense or to do a hit on somebody.LOL :rofl:
:rofl: :rofl:
Post by: stangzilla on July 25, 2022, 09:26:24 AM
in front of the HST is RMR jhp, in front of the GD is Everglades jhp round nose
I reloaded some of the Everglades projectiles already and tested them and went well. next time I think i'll up the powder charge to the limit of the recommended load for titegroup. and get started loading the RMR projectiles next
on their website they say they tested these jhp and they expand to about .6 inches :thumbsup:
(https://live.staticflickr.com/65535/52238721505_e2f35d5466_c.jpg)
Post by: stangzilla on August 05, 2022, 08:01:13 AM
on the left is Everglades Ammo JHP V2
on the right is Montana Gold JHP
(https://live.staticflickr.com/65535/52263796602_606b18cb7c_c.jpg)
Post by: aletheuo137 on August 29, 2022, 08:51:40 AM
(https://uploads.tapatalk-cdn.com/20220829/fa37d5f4237d25cbb54e94adcdc7a729.jpg)Sent from my SM-A102U using Tapatalk
Post by: stangzilla on September 09, 2022, 09:25:29 AM
(https://live.staticflickr.com/65535/52345108663_1a17aac518_c.jpg)
Post by: wirecounter on September 11, 2022, 07:56:52 PM
heads
Heads
Post by: aletheuo137 on October 29, 2022, 07:58:21 PM
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on December 04, 2022, 06:31:36 PM
(https://uploads.tapatalk-cdn.com/20221205/948acaef758385b46b199183c77a78f6.jpg)Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on December 29, 2022, 07:03:12 PM
Sent from my SM-A102U using Tapatalk
Post by: aletheuo137 on January 01, 2023, 04:21:59 PM
Sent from my SM-A102U using Tapatalk
(https://uploads.tapatalk-cdn.com/20230102/ab70fa438feebd6256618bf3acd4db87.jpg)
Post by: aletheuo137 on January 13, 2023, 07:49:52 PM
Sent from my SM-A102U using Tapatalk
Post by: stangzilla on March 07, 2023, 03:37:13 PM
taking it back to the old school :thumbsup:
(https://live.staticflickr.com/65535/52720679686_985d4baeba_c.jpg)
Post by: stangzilla on March 28, 2023, 01:01:55 PM
getting ready for kokohead to re-open
(https://live.staticflickr.com/65535/52778450315_e48c48d783_b.jpg)
Post by: aletheuo137 on April 01, 2023, 03:57:37 PM
Sent from my moto g power (2021) using Tapatalk
Post by: stangzilla on April 07, 2023, 05:20:47 PM
the heads on these are long. it just makes it inside the cylinder. did a heavy crimp so it wont creep. and loaded to only moderate velocity so also wont creep. hopefully
(https://live.staticflickr.com/65535/52798680117_c9e34ec356_b.jpg)
(https://live.staticflickr.com/65535/52799487999_bc0296163c_b.jpg)
Post by: aletheuo137 on April 11, 2023, 08:21:33 PM
Sent from my moto g power (2021) using Tapatalk
Post by: aletheuo137 on May 11, 2023, 07:05:47 AM
Sent from my moto g power (2021) using Tapatalk
Post by: stangzilla on July 17, 2023, 01:54:06 PM
168 grain tipped HPBT. which I believe are Hornady ELD-M bullets. 308 caliber
77 grain HPBT, which are SMK. 223 caliber
I got 600 of the 223, and 400 of the 308
total savings was $180. not bad :geekdanc:
(https://live.staticflickr.com/65535/53049263611_30ef4b50db_b.jpg)
Post by: macsak on July 17, 2023, 03:46:34 PM
got these factory seconds on sale from midway, had free shipping too
168 grain tipped HPBT. which I believe are Hornady ELD-M bullets. 308 caliber
77 grain HPBT, which are SMK. 223 caliber
I got 600 of the 223, and 400 of the 308
total savings was $180. not bad :geekdanc:
(https://live.staticflickr.com/65535/53049263611_30ef4b50db_b.jpg)
Post by: aletheuo137 on July 17, 2023, 06:55:41 PM
260 rem(https://uploads.tapatalk-cdn.com/20230718/4533325bdc5956b1fd301f87d6561f60.jpg)
Sent from my moto g power (2021) using Tapatalk
Post by: aletheuo137 on July 17, 2023, 06:56:08 PM
headsTails never fails!
Sent from my moto g power (2021) using Tapatalk
Post by: ren on July 17, 2023, 08:25:28 PM
heads
(https://media.istockphoto.com/photos/low-angle-view-of-spooky-male-dentist-with-pliers-picture-id470318700?k=6&m=470318700&s=612x612&w=0&h=0H6JtL-4sVWJ9VkdWNQ0rh53ib-9opu5VBDR2H5n774=)
Post by: aletheuo137 on July 23, 2023, 07:21:34 PM
Sent from my moto g power (2021) using Tapatalk
Post by: randay on August 07, 2023, 11:00:09 AM
Post by: 808Hunta on September 07, 2023, 07:12:50 AM
Only got quick pics of the PRC and 308 lol
Post by: oldfart on September 17, 2023, 03:37:58 AM
(https://i.postimg.cc/HWXxNRBv/20230917-030948.jpg) (https://postimages.org/)
Post by: aletheuo137 on September 18, 2023, 05:27:24 PM
Sent from my moto g power (2021) using Tapatalk
Post by: jase90 on September 24, 2023, 09:01:56 PM
Post by: oldfart on October 09, 2023, 09:28:59 PM
Post by: aletheuo137 on October 20, 2023, 06:53:24 AM
(https://uploads.tapatalk-cdn.com/20231020/baee4772d96d9508add081b2472aeeb2.jpg)Sent from my moto g power (2021) using Tapatalk
Post by: Flapp_Jackson on October 20, 2023, 08:55:54 AM
I would call that good!
Not sure you understand the term "reloading" ...
:geekdanc:
Post by: aletheuo137 on October 20, 2023, 12:32:43 PM
Not sure you understand the term "reloading" ...Reloaded old arrows. And title starts out with what did you do?
:geekdanc:
Sent from my moto g power (2021) using Tapatalk
Post by: Flapp_Jackson on October 20, 2023, 12:37:25 PM
Reloaded old arrows. And title starts out with what did you do?
i reloaded film in my 35mm camera and shot a mongoose with it.
I guess anything is fair game if you want to be cleverly obtuse.
(obtusely clever?)
:geekdanc: :shaka:
Post by: ren on October 20, 2023, 12:42:15 PM
i reloaded film in my 35mm camera and shot a mongoose with it.
I guess anything is fair game if you want to be cleverly obtuse.
(obtusely clever?)
:geekdanc: :shaka:
#youold
Post by: Flapp_Jackson on October 20, 2023, 12:45:42 PM
#youold
As is my camera. :thumbsup:
Post by: dogman on October 20, 2023, 05:26:45 PM
Not sure you understand the term "reloading" ...or "room" :)
:geekdanc:
Post by: aletheuo137 on October 22, 2023, 07:10:28 PM
i reloaded film in my 35mm camera and shot a mongoose with it.But did you reload it your room and then out to take a shot?
I guess anything is fair game if you want to be cleverly obtuse.
(obtusely clever?)
:geekdanc: :shaka:
Sent from my moto g power (2021) using Tapatalk
Post by: aletheuo137 on October 22, 2023, 07:11:34 PM
or "room" :)Started in my reloading room and that was the end result
Sent from my moto g power (2021) using Tapatalk
Post by: oldfart on October 27, 2023, 04:35:56 PM
Post by: dogman on October 27, 2023, 06:58:19 PM
I don't recall ever seeing primers all facing the same direction right out of the box.I have, twice. Both times the were facing the opposite of your box. >:(
Post by: stangzilla on October 30, 2023, 09:17:41 AM
H110
(https://live.staticflickr.com/65535/53298378658_bd6285353d_c.jpg)
Post by: stangzilla on November 02, 2023, 04:56:55 PM
I forgot I loaded these 9mm ammo 1 year ago. Couldn't shoot it bc kokohead was closed. Rocky Mountain Reloading, 115 grains, jhp "Nuke"
](https://live.staticflickr.com/65535/53305080136_95b217053b_b.jpg)
Post by: macsak on November 02, 2023, 04:59:50 PM
I forgot I loaded these 9mm ammo 1 year ago. Couldn't shoot it bc kokohead was closed. Rocky Mountain Reloading, 115 grains, jhp "Nuke"
](https://live.staticflickr.com/65535/53305080136_95b217053b_b.jpg)
Post by: stangzilla on November 02, 2023, 05:07:24 PM
those are some weird looking heads...
Heads ;D
Post by: oldfart on November 02, 2023, 06:34:06 PM
Heads ;D=========
(https://i.postimg.cc/Y258d2kG/20220325_115849.jpg) (https://postimg.cc/RqTcFBW4)
I did these about a year ago and they still make me happy.
I don't know why.
Post by: stangzilla on November 06, 2023, 09:46:32 AM
(https://live.staticflickr.com/65535/53306319766_4d92b090fc_c.jpg)
and then after that I'll do some lead 230 grain LRN 45acp from Rim Rock Bullets. after that I'll do some 115 grain LRN, and 185 grain LSWCHP. all from Rim Rock Bullets. look how big the HP is on the 44
(https://live.staticflickr.com/65535/53314002966_4a8a5c9e07_c.jpg)
Post by: 808Hunta on November 06, 2023, 06:51:47 PM
Post by: oldfart on November 06, 2023, 07:01:29 PM
Hopefully can get some rounds downrange with this little guy soon. So far... I'm loving the look, feel n size of this thing. It fits rather easily in my cargo pocket even in my front pocket with tripod. From what my friends told me about is operation and from what I've read so far on the web. CAN'T WAIT to use it!cool :shaka:
Post by: oldfart on November 08, 2023, 01:26:19 AM
cleaned up about 2 or 3k 45acp shells
Post by: oldfart on November 10, 2023, 06:42:47 PM
I ran off a few hundred practice loads and use old newspapers to clean them up before boxing them up. One of the pieces of newspaper was Midweek from 2 years ago. It had an obituary written by Ron Nagasawa. It was for veteran news man Bob Jones.
For those of you who are too young to know Bob, he was a Vietnam War correspondent. Then he worked as an anchor and reporter for kgmb TV. In later years, he wrote a weekly column for Midweek from his banyan tree house in Kahala.
Bob passed away almost exactly 2 years ago. He was an actual friend... Not the Facebook kind. :rofl:
Post by: stangzilla on November 10, 2023, 07:05:05 PM
Tomorrow is Veteran's Day.
I ran off a few hundred practice loads and use old newspapers to clean them up before boxing them up. One of the pieces of newspaper was Midweek from 2 years ago. It had an obituary written by Ron Nagasawa. It was for veteran news man Bob Jones.
For those of you who are too young to know Bob, he was a Vietnam War correspondent. Then he worked as an anchor and reporter for kgmb TV. In later years, he wrote a weekly column for Midweek from his banyan tree house in Kahala.
Bob passed away almost exactly 2 years ago. He was an actual friend... Not the Facebook kind. :rofl:
nice!
I am old enough to remember Bob Jones. great news guy. :thumbsup:
Post by: stangzilla on November 10, 2023, 07:08:03 PM
bc I'm an old fool from the old school that is so cool O0 ;)
(https://live.staticflickr.com/65535/53321776951_6fee484e95_b.jpg)
Post by: oldfart on November 10, 2023, 07:14:57 PM
They make frame-worthy pictures. :thumbsup:
I seen some of yours too. :thumbsup:
(https://i.postimg.cc/P5HyRKZq/francis2.png) (https://postimg.cc/N5NRy6dh)
Post by: stangzilla on November 10, 2023, 11:14:11 PM
I love light bullets and slow powder.
They make frame-worthy pictures. :thumbsup:
I seen some of yours too. :thumbsup:
(https://i.postimg.cc/P5HyRKZq/francis2.png) (https://postimg.cc/N5NRy6dh)
nice! :shaka:
and then shoot out of short barrel for a big fireball! good times! :geekdanc:
Post by: stangzilla on November 20, 2023, 08:56:51 AM
(https://live.staticflickr.com/65535/53343000037_c9fa167b25_c.jpg)
Post by: oldfart on November 20, 2023, 09:28:25 AM
45acp....
Yep me too...to replace what I burned on Saturday.
Just a medium target semiwadcutter for practicing.
Post by: macsak on November 20, 2023, 11:00:35 AM
45acp
(https://live.staticflickr.com/65535/53343000037_c9fa167b25_c.jpg)
Post by: oldfart on November 20, 2023, 12:54:39 PM
heads....
Circumcised?
Post by: aletheuo137 on November 23, 2023, 10:48:41 AM
Sent from my moto g power (2021) using Tapatalk
Post by: stangzilla on November 27, 2023, 07:24:27 AM
(https://live.staticflickr.com/65535/53356891102_38fc034bfc_c.jpg)
Post by: oldfart on November 27, 2023, 09:24:39 AM
Post by: jase90 on November 27, 2023, 08:40:57 PM
those look exactly like my doggy's red rocket
I can't unsee now. Thanks Dave. Ill make sure everyone else I see with FTX bullets knows too so they can't unsee it :rofl:
Post by: oldfart on November 27, 2023, 09:01:19 PM
I can't unsee now. Thanks Dave. Ill make sure everyone else I see with FTX bullets knows too so they can't unsee it :rofl:....
no problem...anytime
:rofl:
Post by: aletheuo137 on November 28, 2023, 06:28:55 AM
those look exactly like my doggy's red rockethttps://youtube.com/watch?v=aNddW2xmZp8
Sent from my moto g power (2021) using Tapatalk
Post by: stangzilla on December 04, 2023, 08:49:57 AM
(https://live.staticflickr.com/65535/53374470992_5a7ebef9d1_c.jpg)
Post by: oldfart on December 04, 2023, 09:33:54 AM
115 grain 9mm LRN from Rim Rock Bullets...
(https://live.staticflickr.com/65535/53374470992_5a7ebef9d1_c.jpg)
Grease groove bullet? What's the load?
Post by: stangzilla on December 04, 2023, 10:51:50 AM
...
Grease groove bullet? What's the load?
yes, grease groove
load is with 7.3 grains of Accurate #7.
Post by: oldfart on December 04, 2023, 12:33:23 PM
yes, grease groove...
load is with 7.3 grains of Accurate #7.
Diameter???
From past experience, success with lead bullets in 9mm is contingent on getting the bullet to grab the rifling. So the diameter of the bullet has to be big enough to match the bore of the gun. Unfortunately, 9mm bore diameter can vary greatly. Especially in vintage guns. I've seen lead 9mm fly sideways due to that. 🤣🤣group sizes about the size of my refrigerator.
Post by: stangzilla on December 04, 2023, 12:55:03 PM
...
Diameter???
From past experience, success with lead bullets in 9mm is contingent on getting the bullet to grab the rifling. So the diameter of the bullet has to be big enough to match the bore of the gun. Unfortunately, 9mm bore diameter can vary greatly. Especially in vintage guns. I've seen lead 9mm fly sideways due to that. 🤣🤣group sizes about the size of my refrigerator.
diameter is .356
Post by: stangzilla on December 05, 2023, 08:42:53 AM
...
Diameter???
From past experience, success with lead bullets in 9mm is contingent on getting the bullet to grab the rifling. So the diameter of the bullet has to be big enough to match the bore of the gun. Unfortunately, 9mm bore diameter can vary greatly. Especially in vintage guns. I've seen lead 9mm fly sideways due to that. 🤣🤣group sizes about the size of my refrigerator.
seems like a lot of people go with .358 for lead bullets
Post by: oldfart on December 05, 2023, 01:42:37 PM
seems like a lot of people go with .358 for lead bullets===========
I've ordered 9mm in 357 dia just to test.
358 might bulge the tapered 9 case too much.
356 usually works for most modern guns but the speed has to be fairly low.
Slow burning powder is the way to go for lead 9mm.
AA7 sounds ok but I used Unique.
Post by: stangzilla on December 06, 2023, 02:32:07 PM
Post by: oldfart on December 06, 2023, 08:02:11 PM
I'll test out the 9mm LRN this weekend in my Glock 19 and Sig P226 Legion :shaka:============
good luck
I'm going on Saturday to photograph a shooting match which I hope is still on.
Then I'll pop over to the pistol side for my usual embarrassing practice session.
Curious to know...
btw, does your G19 have cut rifling or that funky smooth rifling?
also how much AA7 you put inside?
For this Saturday, I'm going to shoot my old 45 as usual but I just switched to BE powder because I'm trying to use up a few pounds of this old stuff.
It's at least 20 years old. Maybe 30 yrs. I know it's still ok because I made a small batch to test last week.
Post by: stangzilla on December 07, 2023, 05:23:16 AM
============
good luck
I'm going on Saturday to photograph a shooting match which I hope is still on.
Then I'll pop over to the pistol side for my usual embarrassing practice session.
Curious to know...
btw, does your G19 have cut rifling or that funky smooth rifling?
also how much AA7 you put inside?
For this Saturday, I'm going to shoot my old 45 as usual but I just switched to BE powder because I'm trying to use up a few pounds of this old stuff.
It's at least 20 years old. Maybe 30 yrs. I know it's still ok because I made a small batch to test last week.
7.3 grains of ACC #7
Post by: stangzilla on December 07, 2023, 08:51:12 PM
Post by: oldfart on December 07, 2023, 09:21:39 PM
Dammit, I just sold 2 lbs of BE to Lihikai really cheap. :rofl:
Post by: randay on January 03, 2024, 04:13:12 PM
Post by: randay on January 12, 2024, 06:24:57 AM
Post by: oldfart on January 12, 2024, 08:11:31 AM
Post by: oldfart on February 06, 2024, 06:31:32 AM
185 gr LSWC BB over 4.2 BE
IIRC I got the bullets from Randay
Post by: oldfart on February 24, 2024, 02:23:30 PM
Post by: mrgaf on February 27, 2024, 08:36:32 PM
Well here’s a list
Threw away a perfectly good RCBS Summit press and Inline Fabrication Quick detach mount and mounting plate for the Summit press. Why? Had no more use for it and it was just taking up real estate.
Broke out my Lee C frame and quick detach mount and will start using them for odds and ends work not suited for my Lee turret press
Threw out 15 or 20 Hornady lock and load bushings, 9mm, 30-06, 30-30, 25 WSSM, 25-06, 45-70 and 50-120 dies sets and shell holders
There was more minor stuff I no longer used or wanted.
Time to move on….. :thumbsup:
Post by: oldfart on February 28, 2024, 02:56:47 AM
What did I do?...
Well here’s a list
Threw away a perfectly good RCBS Summit press and Inline Fabrication Quick detach mount and mounting plate for the Summit press. Why? Had no more use for it and it was just taking up real estate.
Broke out my Lee C frame and quick detach mount and will start using them for odds and ends work not suited for my Lee turret press
Threw out 15 or 20 Hornady lock and load bushings, 9mm, 30-06, 30-30, 25 WSSM, 25-06, 45-70 and 50-120 dies sets and shell holders
There was more minor stuff I no longer used or wanted.
Time to move on….. :thumbsup:
What a waste of good money.
I easily sold some unused stuff and donated the money to HIFICO to carry on the 2A fight. Somebody wanted to buy my old Lee press a few weeks ago. People always want dies. I took a table at the gun show to sell unwanted stuff to raise money for HIFICO. I was just about to put out a call for stuff to put on the table. You could have donated it to a new shooter to learn to reload. If you don't promote the shooting sports to the next generation then we really lost the battle.
Post by: mrgaf on February 28, 2024, 07:53:01 AM
...
What a waste of good money.
I easily sold some unused stuff and donated the money to HIFICO to carry on the 2A fight. Somebody wanted to buy my old Lee press a few weeks ago. People always want dies. I took a table at the gun show to sell unwanted stuff to raise money for HIFICO. I was just about to put out a call for stuff to put on the table. You could have donated it to a new shooter to learn to reload. If you don't promote the shooting sports to the next generation then we really lost the battle.
Sent you a pm…
Post by: stangzilla on July 15, 2024, 09:49:05 AM
245 grain projectile over 7 grains of Titegroup. should be around 1165 fps out of a 20" barrel. for my Marlin lever gun. some easier shooting ammo :geekdanc:
(https://live.staticflickr.com/65535/53856531057_791ced9eb1_c.jpg)
Post by: oldfart on July 15, 2024, 12:55:52 PM
Here is something cool that I saw yesterday from a black powder shooter.
These are black powder percussion caps made from an upcycled Orange Crush soda can.
Post by: oldfart on July 28, 2024, 03:23:47 AM
But the linkage on my Dillon powder measure sort of broke. Nothing serious, just annoying.
It's around 35 yrs old so I can't really complain.
Post by: jc2721 on July 28, 2024, 11:54:28 PM
This afternoon the .45 ACP factory crimp die I ordered came in but not the .38 Super.
Post by: stangzilla on July 29, 2024, 07:28:26 AM
(https://live.staticflickr.com/65535/53885958779_54e16788dd_c.jpg)
Post by: oldfart on August 08, 2024, 06:13:46 AM
Post by: oldfart on August 26, 2024, 08:57:04 AM
(https://i.postimg.cc/3wvYg54g/20240826-080652.jpg) (https://postimages.org/)
The media is starting to look grungy and the motor bearings need lube. To save money, I might try washing the media. It's my blend of corn and walnut.
Post by: oldfart on September 22, 2024, 03:43:11 AM
I use newspapers to wipe off the residual case lube.
Thank you j.green for attempting to shut down our public range.
(https://i.postimg.cc/xjwpphRB/Greenammo7.jpg) (https://postimages.org/)
Post by: oldfart on September 23, 2024, 08:24:10 AM
It is a soft swaged lead swc hp. It is powered by a light charge of bullseye because the metal is so soft I can easily dent it with my fingernail.
Also, if you drive it too fast, it will foul your bbl and the low recoil is better for arthritic fingers.
Furthermore, it hangs up on the throat because the metal is too soft. Seating depth appears long, but it's not.
Basically, it's crappy ammo.
The only reason I shoot it is because I got the bullets cheap.
Post by: oldfart on November 28, 2024, 09:04:51 AM
Just low power stuff. 200 gr. at about 750 fps.
I need the practice. Muscles and eyesight are getting old. :(
Post by: oldfart on February 15, 2025, 08:30:05 PM
These are not great for action pistol competition. Even my hot load didn't make major pf while burning quite a bit of powder.
I'll just use these for marksmanship practice.
Photograph is in the "going to the range" thread.
Post by: stangzilla on February 19, 2025, 12:20:59 PM
(https://live.staticflickr.com/65535/54335059005_930777dd47_c.jpg)
Post by: oldfart on February 19, 2025, 01:03:14 PM
Hornady FTX 44 magnum 225 grains. H110....
(https://live.staticflickr.com/65535/54335059005_930777dd47_c.jpg)
Kind of reminds me of my dog...
Post by: oldfart on February 27, 2025, 12:17:40 AM
So I loaded 50 rounds using that brass to see if I can figure out if there is a chronic problem.
The first thing I noticed was that quality control seems spotty.
The headstamps are NOT consistent. The lettering seems to vary.
Will shoot these on Friday, if possible.
(conventional 200 gr LSWC with 4.2 Bullseye and Winchester primers...a mild practice load)
Post by: stangzilla on March 03, 2025, 07:35:19 AM
heads
(https://live.staticflickr.com/65535/54362216327_1507c74868_c.jpg)
(https://live.staticflickr.com/65535/54363313163_24ddf6cb1c_c.jpg)
Post by: oldfart on March 03, 2025, 08:05:56 AM
Post by: macsak on March 03, 2025, 08:25:33 AM
45acp Stan's cast lead bullets LSWC
heads
(https://live.staticflickr.com/65535/54362216327_1507c74868_c.jpg)
(https://live.staticflickr.com/65535/54363313163_24ddf6cb1c_c.jpg)
Post by: stangzilla on March 03, 2025, 09:48:07 AM
Nice...did Stan make those bullets?
yes. first time using his projectiles. looks really nice. I'll test them out this weekend. my friend just got a new chrono, so we'll see how the velocity is too. using 7.7 grains of accurate #5 which is the recommended starting load according to my book. looking forward to it
I'll probably get more from Stan in 357 and 44. he does nice work for a great price.
Post by: oldfart on March 03, 2025, 01:19:22 PM
Post by: stangzilla on March 03, 2025, 03:13:05 PM
I'm going to shoot these 45's out of my Ruger Vaquero. love that gun. shoots great for having only a rear gutter site
then I'll load more and shoot out of my 1911's
Post by: oldfart on March 03, 2025, 03:30:40 PM
he is a really good guy to do such work at a very fair price. and the presentation in the box is great. it must be very time consuming====
I'm going to shoot these 45's out of my Ruger Vaquero. love that gun. shoots great for having only a rear gutter site
then I'll load more and shoot out of my 1911's
I used to pay my kids a few bucks to stack up my bullets like that.
I also paid them to load the primer tubes.
Post by: stangzilla on March 03, 2025, 05:51:28 PM
Post by: stangzilla on March 10, 2025, 07:44:12 AM
45acp Stan's cast lead bullets LSWC
heads
(https://live.staticflickr.com/65535/54362216327_1507c74868_c.jpg)
(https://live.staticflickr.com/65535/54363313163_24ddf6cb1c_c.jpg)
the OAL was .021 too long. the cylinder could not turn. even in my friend's 1911 every 1/5 rounds it would not go into battery. tap did not work so I racked the slide and ejected the round. went home and seated the bullet .021" shorter and now it will turn in the cyllinder. go back again to test the function. learned something :thumbsup:
Post by: oldfart on March 11, 2025, 05:24:11 AM
But I also make sure there is not more than about 1/32 inch of exposed shoulder.
The term #68 refers to the Hensley and Gibbs mould design.
Other mould makers make similar bullets but not exactly the same.
I'm guessing that Stan is using saeco moulds. I should ask him.
I taper crimp to 0.468 for maximum reliability.
Post by: stangzilla on March 11, 2025, 11:06:04 AM
it was 1.258 and that was too long
Post by: oldfart on March 11, 2025, 12:12:48 PM
my OAL now is 1.237...
it was 1.258 and that was too long
What's the diameter of the case mouth after crimp?
That can cause failure to chamber completely.
Also, some new guns have very tight chambers.
Also, bullets that use a polymer coating might be too tight in the chamber.
Nowadays I insist on verifying my reloads in the particular gun that will shoot them.
Post by: stangzilla on March 16, 2025, 09:57:36 AM
...
What's the diameter of the case mouth after crimp?
That can cause failure to chamber completely.
Also, some new guns have very tight chambers.
Also, bullets that use a polymer coating might be too tight in the chamber.
Nowadays I insist on verifying my reloads in the particular gun that will shoot them.
No crimp. Haha!
Post by: stangzilla on March 17, 2025, 12:32:24 PM
(https://live.staticflickr.com/65535/54392673972_6e95efdd59_c.jpg)
Post by: macsak on March 17, 2025, 12:53:51 PM
my 45acp handloads with Stan's projectiles. 7.7 grains of Accurate #5. average 868.4 fps
(https://live.staticflickr.com/65535/54392673972_6e95efdd59_c.jpg)
Post by: stangzilla on March 17, 2025, 12:56:47 PM
Post by: stangzilla on March 17, 2025, 12:59:53 PM
very consistent velocity...
I'll do some with Titegroup and see how it compares to Acc#5. also got Universal, CFE pistol, and HP38 and some other powders to try
Post by: stangzilla on March 17, 2025, 01:03:31 PM
Post by: oldfart on March 17, 2025, 03:35:56 PM
pretty cool using my friend's Garmin chrono. much mahalo's to him for letting me use it. now I no need go by my palm chrono any more :rofl:===============
geeez...that chrono thing cost more than my gun!!
...
anyway, if you are keeping a record of your ammo testing, don't forget to include standard deviation in your database.
That is a significant statistic for the ammo nerds.
Basically, it predicts where most of your shots will fall.
Post by: oldfart on March 17, 2025, 03:40:23 PM
Even the dawg was scared and demanded to hide inside the house. :rofl:
Still deciding what ammo to load.
Post by: stangzilla on March 17, 2025, 05:02:40 PM
===============
geeez...that chrono thing cost more than my gun!!
...
anyway, if you are keeping a record of your ammo testing, don't forget to include standard deviation in your database.
That is a significant statistic for the ammo nerds.
Basically, it predicts where most of your shots will fall.
thanks. I'll be sure to record the SD next time
I loaded some 357 with H110 to test in a couple weeks out of my new revolver. Ruger Blackhawk convertible 357/9mm :geekdanc:
Post by: stangzilla on March 18, 2025, 09:23:43 AM
(https://live.staticflickr.com/65535/54394383413_eaa2d789b4_c.jpg)
Post by: oldfart on March 18, 2025, 10:23:08 AM
How much H110 you put?
Post by: stangzilla on March 18, 2025, 10:31:57 AM
That's so pretty.
How much H110 you put?
not much. 14.1 grains. start there with the new gun. maybe use more powder next time. see how it shoots first
Post by: oldfart on March 18, 2025, 10:54:05 AM
not much. 14.1 grains. start there with the new gun. maybe use more powder next time. see how it shoots first.....
That's way lighter than I ever used.
For that bullet, I would have used at least 16.5.
It's more fun like that. :rofl:
Post by: oldfart on March 19, 2025, 07:51:05 AM
(https://i.postimg.cc/4N0sS4b9/20250317-201326.jpg) (https://postimages.org/)
Post by: stangzilla on March 19, 2025, 03:57:12 PM
.....
That's way lighter than I ever used.
For that bullet, I would have used at least 16.5.
It's more fun like that. :rofl:
I'm going to shoot these handloads, some pretty hot Remington 125 grain, and some just factory 9mm and see how they do on the chrono
probably load some hotter JHP for the next time after this or some target loads or both
Post by: oldfart on March 19, 2025, 05:02:29 PM
I'm going to shoot these handloads, some pretty hot Remington 125 grain, and some just factory 9mm and see how they do on the chrono===========
probably load some hotter JHP for the next time after this or some target loads or both
The reasoning behind the hotter charge weight for your 357 is the nature of H110 powder.
H110 is a slow and difficult to ignite powder.
Also, in the 357 shell casing, a lower charge weight might not get close to the flash hole.
FYI-the lowest H110 load I ever used was 14.5 with a hard cast keith-style lead bullet.
This was a great combo because the keith SWC is a fairly long bullet that fills the airspace.
That 14.5 charge provides a satisfying thump with a cheap bullet.
A hard cast poly coat bullet or perhaps a cheap plated bullet might be a fun thing to try with H110 powder.
I've used cheap plated bullets in my 44 mag. It's good low-cost fun ammo.
Post by: stangzilla on March 19, 2025, 08:37:55 PM
158 grain XTP with H110 starting charge is 12.7, top end is 15.6. Half way in between is 14.15. My load is 14.1
. My other book says 15 grains to 16.7
We'll see how my loads go and take it from there :shaka:
Post by: oldfart on March 19, 2025, 08:55:56 PM
Post by: oldfart on March 28, 2025, 04:42:00 AM
They are pretty ordinary lead bullets that I always use.
Loaded a few to test out later. ..maybe today.
Post by: stangzilla on March 31, 2025, 07:43:30 AM
heads
(https://live.staticflickr.com/65535/54419100130_1b92585c33_c.jpg)
Post by: stangzilla on March 31, 2025, 06:04:53 PM
.....
That's way lighter than I ever used.
For that bullet, I would have used at least 16.5.
It's more fun like that. :rofl:
chrono'd the H110 XTP's and was only going about 1100fps, so will go hotter next time
will also load up some of Stan's projectiles to test out with probably ACC #5 bc that powder seems to be pretty accurate
Post by: oldfart on March 31, 2025, 06:53:26 PM
Post by: stangzilla on April 21, 2025, 03:35:40 PM
Post by: stangzilla on April 28, 2025, 09:07:46 AM
loaded some of Stan's 158 grain 357 LSWC projectiles over 8.5 and 9.0 grains of ACC#5. book says 1170 fps and 1220 fps but we will check it on the chrono this weekend and I'll shoot from Lee's pistol rest to test some accuracy. shoot out of my 6" GP100 bc it is my most accurate 357 revolver
pretty good
(https://live.staticflickr.com/65535/54478450731_ed5490677c_c.jpg)
Post by: oldfart on June 18, 2025, 07:43:12 PM
Will load some 45 practice ammo as soon as I get off my a---
:rofl:
Post by: oldfart on August 01, 2025, 08:52:55 PM
Post by: oldfart on August 15, 2025, 07:33:24 PM
I notice the brass I'm using nowadays seems to be cracking more often.
I think the quality of metal isn't as good as it was 40 something years ago.
Post by: aletheuo137 on August 23, 2025, 10:09:32 AM
Post by: oldfart on August 23, 2025, 11:12:30 AM
Post by: aletheuo137 on August 23, 2025, 07:14:08 PM
Nice....what is it?7mm rem mag 150 grain core lok
Sent from my SM-A156U1 using Tapatalk
Post by: stangzilla on September 01, 2025, 02:39:09 AM
8.5 grains ACC#5
1220 fps. SD 14
Everglades ammo 357, 125 grain JHP
19.4 grains H110
1475 fps, SD 21
Next time will load the H110 a little hotter. Not much hotter
Post by: oldfart on September 01, 2025, 03:05:37 AM
Will post results tomorrow.
Post by: aletheuo137 on September 01, 2025, 08:03:32 AM
Conducted a science fair project about using very old gunpowder.Science fair project???
Will post results tomorrow.
Sent from my SM-A156U1 using Tapatalk
Post by: oldfart on September 01, 2025, 10:50:42 AM
Science fair project???...
Sent from my SM-A156U1 using Tapatalk
Yep...standby.. :rofl:
Post by: Rocky on September 02, 2025, 09:18:53 AM
Ran off 150 rnds of medium 45 practice ammo for tomorrow.HOT TIP !
I notice the brass I'm using nowadays seems to be cracking more often.
I think the quality of metal isn't as good as it was 40 something years ago.
"using very old gunpowder."
Too Pake.
And don't keep reloading same cases for 40 years ! :rofl:
:wave:
Post by: oldfart on September 03, 2025, 04:25:52 AM
HOT TIP !....
Too Pake.
And don't keep reloading same cases for 40 years ! :rofl:
:wave:
Lol
It's in the blood.
Pake no throw away nothing.
Post by: E808AN on September 03, 2025, 08:53:02 PM
Out of my DD 16 inch
Sierra 77gr Cannelure, 2770 FPS Avg. Still under the 5.56 max pressure according to QL.
Compared to the Brass case on the left going 2700 running ~2000psi hotter according to QL
Going to try Nosler 70gr RDF soon.
Post by: oldfart on September 06, 2025, 07:03:14 PM
Post by: oldfart on September 29, 2025, 10:05:04 PM
Just loaded some 45 practice ammo for a friday session.
A part flew off my dillon press. I couldn't find it, but I did have a spare.
Will contact dillon for a replacement. This happened before.
The press is about 40 yrs old so it's starting to fall apart....just like people.
Post by: aletheuo137 on October 01, 2025, 06:36:56 AM
Sent from my SM-A156U1 using Tapatalk
Post by: oldfart on December 09, 2025, 07:25:10 PM
However, I used powder that was about 70 years old.
Ref. My post from September 2 a few months ago.
I test fired some at that time and test fired a round today.
I want to chrono this batch later this week.
Post by: Rocky on December 10, 2025, 07:22:41 AM
nothing weird today
Just loaded some 45 practice ammo for a friday session.
A part flew off my dillon press. I couldn't find it, but I did have a spare.
Will contact dillon for a replacement. This happened before.
The press is about 40 yrs old so it's starting to fall apart....just like people.
Dillon does rebuilding service.
Sent a 550B a few years back (I paid for shipping) and the cleaned and rebuilt it.
Here was my deal but they do all machines
Turn around was quick, well worth it ! :D
RL550 Service & Refurbishment
From
$145.00
or 4 payments of $36.25 with Sezzle ⓘ
Services include
1. Disassembly + Solvent Tank Bath
2. Detailed Inspection & Replacement of Worn Out Parts
3. Re-assembly and Full Machine Lubrication
4. Testing all Pertinent Systems, Including Machine Timing
5. OEM Packaged and Shipped Right Back to You
Heres the link
https://www.dillonprecision.com/service-center
Post by: Rocky on December 10, 2025, 07:23:46 AM
Trying to improve on accuracy!(https://uploads.tapatalk-cdn.com/20251001/2af3659077f03e69e12bc239ce330896.jpg)
Keep both eyes open ! :rofl: :rofl:
:wave:
Post by: oldfart on December 12, 2025, 11:54:09 PM
I loaded about 150 rnds of 45acp practice ammo.=============
However, I used powder that was about 70 years old.
Ref. My post from September 2 a few months ago.
I test fired some at that time and test fired a round today.
I want to chrono this batch later this week.
dec.12-
chrono result of that 70 year old powder test ammo
45acp-200 gr Missouri swc-4.1 gr Bullseye1955-WLP
815 fps-Sd=10
better than I expected!
Post by: stangzilla on January 05, 2026, 06:16:39 PM
(https://live.staticflickr.com/65535/55025690876_b15fdfc72a_c.jpg)
Post by: oldfart on January 05, 2026, 06:35:08 PM
Post by: ren on January 05, 2026, 07:12:53 PM
Testing NAS3 cases mainly for competition use where brass pick up isnt possible or ideal due to time constraints
Out of my DD 16 inch
Sierra 77gr Cannelure, 2770 FPS Avg. Still under the 5.56 max pressure according to QL.
Compared to the Brass case on the left going 2700 running ~2000psi hotter according to QL
Going to try Nosler 70gr RDF soon.
that's a healthy velocity out of a 16" barrel. What powder did you use?