2aHawaii

General Topics => Off Topic => Topic started by: Rocky on November 07, 2022, 08:02:02 AM

Title: scope zero's
Post by: Rocky on November 07, 2022, 08:02:02 AM
Did some laser  .22  zeroing yesterday.

Title: Re: scope zero's
Post by: drck1000 on November 07, 2022, 08:06:32 AM
Did you check torque on everything?

Is rail monolithic? Or bolted on?
Title: Re: scope zero's
Post by: Rocky on November 07, 2022, 02:53:46 PM
Did you check torque on everything?
Is rail monolithic? Or bolted on?

 monolithic
Torqued to spec.
Both of these guys know what their doing unlike my novice self.
Title: Re: scope zero's
Post by: ren on November 07, 2022, 03:49:55 PM
are the rings mounted close to the adjustment turrets?
Title: Re: scope zero's
Post by: hvybarrels on November 07, 2022, 08:33:25 PM
I got one of those sight-in lasers that magnetically attaches to the front of the barrel, so hopefully I’ll at least be on paper when the range opens up again.

It won’t help if you forgot to use loc tite though
Title: Re: scope zero's
Post by: robtmc on November 08, 2022, 06:28:43 AM
Parrallax error if you are not consistent on cheek weld?   I only started using scopes a few years ago and found out real fast about that.
Got real attentive to mounting the scopes as low as possible and paying attention to repeating the hold.
Title: Re: scope zero's
Post by: Rocky on November 08, 2022, 07:07:24 AM
1st rifle was a build by one extremely  knowledgeable and zeroed
second scope  was merely tightened down from existing  by pro shooter. who was shooting dime the day before
Shooting was done with rifle in sled.
Title: Re: scope zero's
Post by: drck1000 on November 08, 2022, 07:33:39 AM
monolithic
Torqued to spec.
Both of these guys know what their doing unlike my novice self.
Then again, I had the Leo.  :D
I recently had a brand new ZCO that was not able to zero.  Was impacting about 20 feet in front of the target.  And that was after the boresighted shot #1 was maybe inch or so low and right.  Brand new custom rifle as well, so was  ???

Ended up the brake body got cross threaded, likely in transit.  Where the collar was still tight, but the brake was every so slightly off, and led to a very slight baffle strike.  The first range session was a bust.  Swapped scope to a "known good" rifle and was fine, so isolated the rifle. 
Title: Re: scope zero's
Post by: Rocky on November 08, 2022, 08:09:05 AM
Using 12" square with 1 large 8" center target and 1 small 3'' circle target in each corner
Aiming for 8'' center, first shot POI was lower right corner corner


Title: Re: scope zero's
Post by: Rocky on November 08, 2022, 08:26:58 AM
It won’t help if you forgot to use loc tite though

Orange
Title: Re: scope zero's
Post by: drck1000 on November 08, 2022, 08:57:02 AM
A number of scope mounts recommend against use of loctite or other liquid based adhesives.  I use Spuhr and American Rifle Company and both recommend against use of loctite.  I believe Vortex recommends against as well.

I've personally never used loctite on any scope mounts.  Mostly for bolt action rifles though.  I have a NF with Geissele mount on an AR and after shooting that gun in a couple of rifle courses with round counts in the 300-500 range and hasn't moved. 

I do know many who will use loctite and stuff like rosin.  To each their own.  I know some who have had screws walk on them and lead to an issue 'in the field'.