2aHawaii
General Topics => Preparedness and Survival => Topic started by: macsak on September 02, 2023, 10:01:26 PM
-
https://www.youtube.com/watch?v=1uaf47U9DLo
-
If you're just replacing or installing a latch and/or deadbolt on an existing door, then repositioning the striker plate isn't always good enough.
As you saw in his demonstration, the weather stripping cushions the door against the stop moulding. If a burglar pushes hard enough on an outward opening door, or inversely pulls on an inward opening door, he might find the weather stripping "gives" (compresses) enough to let that safety pin fall into the striker plate hole.
The best way to stop this from happening is to make your door stop moulding seated right up against the door when closed. if you have cushy weather stripping, though, that might not be a good fix.
in case of weather stripping, you might be able to drill a few holes beneath or next to the weatherstripping to insert steel pins -- the kind you use for shelf supports. Not the ones with flat ends -- those are probably too short. Use the barrel kind, and make sure they are at least twice as long as the part of the pin you leave showing or longer.
i just installed a steel door on my workshop, and there was weather stripping already included (pre-hung door from HD). So I removed the weather stripping to make it easier to close, and I drilled a hole right behind the striker plate for a 40mm long M5 diameter shelf pin. i placed the hole against the door when it's closed. I also added some tape around the pin for noise reduction and to fine tune the closing position.
Now the door shuts exactly where I want it, and there's no way for anyone to get the latch to travel and cause the safety latch to disengage without destroying the door jamb. If they are willing to do that, then protecting against a door latch attack is not going to stop them.
For my front door, I'm in the process of rebuilding the frame/jamb. No weather stripping, and the stop moulding is not only against the door to prevent the latch problem, but I made my own 2 1/4" wide, 3/8" thick stop moulding. it's that wide because it does double duty: stop for the exterior entrance door as well as stop for the screen door.
Given how easy it might be on some homes to pry the stop moulding off some exterior doors, having a few steel pins embedded in the jamb to act as stops wouldn't be a terrible idea.
Also, one of the biggest mistakes people overlook is the deadbolt they install on a door with a glass window or a door next to a window. If the interior deadbolt mechanism is something you can turn by hand, then anyone can break the glass and reach in to unlock the deadbolt, assuming they can reach from the window to the door.
I use a double cylinder deadbolt. You need a key to lock & unlock it from either side. I leave a key near the door, but away from any windows, both for convenience and emergencies. Don't want to be searching for a key if you really need to get out or keep someone out trying to come inside.
Door security is an entire niche industry. You can get all kinds of upgrades to make the door impossible to kick in, super thick striker plates with extra, longer screws instead of just the 2 short ones the door knob and deadbolt makers include for strike plates, and so on.
https://www.amazon.com/security-strike-plate/s?k=security+strike+plate
-
BTW, if you have a door with the hinge pins on the side of the jamb that an attacker might try removing the pins, there's a fix for that using the shelf pins, too.
In your top hinge, drill two holes -- one on each side and where the holes will meet when the hinge closes. Taking the hinge to a drill press helps with this step -- simple to line them up.
Then drive the shelf pin into either hole, leaving a little more than the thickness of the hinge exposed.
Now when the door closes, the pin will be seated inside the new holes in the hinge. If someone removes the hinge pin, the two sides can not be separated while the hinge is still closed and the shelf pin is in place.
I've seen some recommend taking a hinge screw out of one side and drill the hole in the other half of the hinge. That saves some drilling, but for heavy doors, you might need the screw there. If you have 2 screw holes that align when closed, again you can remove 2 screws and save any drilling. You may or may not miss those screws -- depends on the door.
You can also buy hinges that come with a tab on one half (similar to what a pin looks like) and an aligned hole on the other half. My new steel door came with those, which made less work for me.
If you have an outward opening entrance door, chances are the hinge pins are exposed.
-
lul of the thread headline
-
BTW, if you have a door with the hinge pins on the side of the jamb that an attacker might try removing the pins, there's a fix for that using the shelf pins, too.
In your top hinge, drill two holes -- one on each side and where the holes will meet when the hinge closes. Taking the hinge to a drill press helps with this step -- simple to line them up.
Then drive the shelf pin into either hole, leaving a little more than the thickness of the hinge exposed.
Now when the door closes, the pin will be seated inside the new holes in the hinge. If someone removes the hinge pin, the two sides can not be separated while the hinge is still closed and the shelf pin is in place.
I've seen some recommend taking a hinge screw out of one side and drill the hole in the other half of the hinge. That saves some drilling, but for heavy doors, you might need the screw there. If you have 2 screw holes that align when closed, again you can remove 2 screws and save any drilling. You may or may not miss those screws -- depends on the door.
You can also buy hinges that come with a tab on one half (similar to what a pin looks like) and an aligned hole on the other half. My new steel door came with those, which made less work for me.
If you have an outward opening entrance door, chances are the hinge pins are exposed.
Just buy "non-rising hing pin" hinges. :crazy:
-
Just buy "non-rising hing pin" hinges. :crazy:
Is that a thing?
I mentioned buying hinges with a tab on one half and a matching hole on the other. is that what you meant?
-
Is that a thing?
I mentioned buying hinges with a tab on one half and a matching hole on the other. is that what you meant?
Also known as "fixed pin", "non removable pin" and "Security hinge"
https://www.amazon.com/Stainless-Steel-Security-Door-Hinges/dp/B01EVJBNJW/ref=asc_df_B01EVJBNJW?tag=bngsmtphsnus-20&linkCode=df0&hvadid=79989588698533&hvnetw=s&hvqmt=e&hvbmt=be&hvdev=c&hvlocint=&hvlocphy=&hvtargid=pla-4583589115540813&psc=1
-
Also known as "fixed pin", "non removable pin" and "Security hinge"
https://www.amazon.com/Stainless-Steel-Security-Door-Hinges/dp/B01EVJBNJW/ref=asc_df_B01EVJBNJW?tag=bngsmtphsnus-20&linkCode=df0&hvadid=79989588698533&hvnetw=s&hvqmt=e&hvbmt=be&hvdev=c&hvlocint=&hvlocphy=&hvtargid=pla-4583589115540813&psc=1
Okay. i might actually have those on my steel shed door. There's no hole beneath the pin to punch them through.
I'm less inclined to "knowingly" :geekdanc: get those because lubricating a hinge properly requires you to pull the pin about halfway out of the hinge. Also, sometimes you need to remove the door, and pulling the pins is easier to take them off AND replace them if you don't remove the hinges. Screwing the hinge screws out and in again can cause them to not be as tight, too.
For clarity, since descriptions are sometimes hard to visualize, here's the "tab" security hinge I mentioned:
https://www.amazon.com/Security-Door-Hinges-Stainless-Radius/dp/B01EVJHJRM/ref=sr_1_6?keywords=Security+Door+Hinges&qid=1694200316&sr=8-6
-
For clarity, since descriptions are sometimes hard to visualize, here's the "tab" security hinge I mentioned:
https://www.amazon.com/Security-Door-Hinges-Stainless-Radius/dp/B01EVJHJRM/ref=sr_1_6?keywords=Security+Door+Hinges&qid=1694200316&sr=8-6
Similar but my posted version has
"Security Tab - Prevents intruders from removing hinges" in case screws exposed
-
Similar but my posted version has
"Security Tab - Prevents intruders from removing hinges" in case screws exposed
I double-checked my shed's hinges. No tabs & holes between hinges, but the bottom of each pin hole is closed, like the one you posted.
I'm happy the door came with security hinges since the pins are on the outside. It's possible they included these hinges since it's a left-handed, outward opening door. For an inward opening door, they might not. Next time i'm at HD and think about it, I might do a hinge check for that just out of curiosity.
Anyway, the shelf pin & hole "upgrade" is one method of turning regular hinges into security hinges without having to buy some.