.223/5.56 MIL Re-loads / Chrono (Read 42940 times)

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #40 on: January 13, 2017, 12:14:59 PM »
As far as patronizing the reloading companies, I don't care. If you can get it free, so be it. I am more than happy to take a pic out of a page and send it to someone.

I'm in the same boat as you... and I'm sure a lot of members here order online vs buying local at times with regards to patronizing large scale companies. I do try to save where possible since this is an expensive hobby. Don't get me wrong, I do buy local when it's something I don't want to wait for, an impulse buy or need that very day.

 :shaka:

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #41 on: January 13, 2017, 12:23:50 PM »
Skipping steps in working a load can cause problems.  I learned the hard way here.  I changed only one variable....  Same bullet weight just a different brand and profile..



I had purchased some brand new cases, and all I wanted to do is fireform them to my chamber.  I didn't want to use expensive target bullets to do this, so I figured I blast some cheap bullets instead.  All the rounds went though the same hole on target at 100yards...  (testament to OCW theory of load development!)    I got through the whole box of 50 that I made before I realized something was wrong when the last few cases wasn't being ejected from the action.  All the rounds went though the same hole on target at 100yards...  (testament to OCW theory of load development!)

If you look at the top cases you can see the blow by and excessively flat the primer. 

problem 1.  I didn't work up the load with the new component
problem 2.  I didn't inspect any of the cases per shot, I didn't think it would make any difference.

Lucky for me, and my face, the only thing that happened is I ruined about half my new cases, damaged the ejector spring, and slightly etched my bolt face.  This is in a high end target action, imagine if this was a semi auto,  Might have blown it up.

Now my very expensive target rifle has and ugly bolt face, and wasted money on new Winchester cases.  could have been much worse.

Noted. I'll stick a single down the chamber and give it a looksie.

However, with the data I got from Bushido. It looks as if I'm in the middle of his hodgedon manuel at 27.2 with it stating 26-27.8gr with the same OAL 2.200".

I'll work the next lot up and batch a few starting from 26-27ish, just a little time consuming since I have an auto disc measure and it requires swapping plates.

 :shaka:

oldfart

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #42 on: January 13, 2017, 12:33:43 PM »
I haven't had any real problems with my Lee progressive. Although Henry is selling his Dillon auto drive 1050xl if you're interested.  :thumbsup:  ;D

I also have a Dillon 450b if that counts, but haven't found it in me yet to buy the 550 conversion kit since the Lee's working pretty good.
...
I meant replace the powder measure with something adjustable. it's nice to be able to dial in what you want rather than pick a puka and hope for the best.

Btw, guys who have been to my house know that that the last thing I need is another press...really.
Interesting that someone would sell a 1050 tho....
Is that Henry at prime sports?
What, Me Worry?

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #43 on: January 13, 2017, 12:36:39 PM »
...
I meant replace the powder measure with something adjustable. it's nice to be able to dial in what you want rather than pick a puka and hope for the best.

Btw, guys who have been to my house know that that the last thing I need is another press...really.
Interesting that someone would sell a 1050 tho....
Is that Henry at prime sports?

WGS, last week when I was there he was trying to get me to buy it.  :rofl: dass da one!

oldfart

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #44 on: January 13, 2017, 12:39:21 PM »
WGS, last week when I was there he was trying to get me to buy it.  :rofl: dass da one!
...
How much for the 1050?
What, Me Worry?

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #45 on: January 13, 2017, 12:43:55 PM »
...
How much for the 1050?

Believe he mentioned 5g since it has the auto drive/touch pad LCD, but don't quote me on that.

He had it in the shop reloading 9mm when Joe was out on vacay, his setup is pretty f'n awesome!  :geekdanc:

macsak

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #46 on: January 13, 2017, 12:56:26 PM »
...
I meant replace the powder measure with something adjustable. it's nice to be able to dial in what you want rather than pick a puka and hope for the best.

Btw, guys who have been to my house know that that the last thing I need is another press...really.
Interesting that someone would sell a 1050 tho....
Is that Henry at prime sports?

not prime sports, must be WGS
prime sports panda no more 1050

oldfart

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #47 on: January 13, 2017, 01:05:50 PM »
Believe he mentioned 5g since it has the auto drive/touch pad LCD, but don't quote me on that.

He had it in the shop reloading 9mm when Joe was out on vacay, his setup is pretty f'n awesome!  :geekdanc:
...
I had to Google the touchpad autodrive. Nice but scary.
There is plenty to go wrong on a 1050 without a motor and a computer.
 :stopjack:
What, Me Worry?

Heavies

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #48 on: January 13, 2017, 05:31:42 PM »
...
I had to Google the touchpad autodrive. Nice but scary.
There is plenty to go wrong on a 1050 without a motor and a computer.
 :stopjack:

Last time I was there he showed it to me, in action, freaking impressive!  You'd need to shoot ALOT to make it worth it.  I think he wanted more than 5 though, can 't remember, I just was thinking "I'd love to have that, but I don't shoot enough to make it worth it... :(  "

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #49 on: January 13, 2017, 08:21:17 PM »
Damn...

I'm surprised the primers didn't blow out with that much blow by.

Today, I shot 20 to 24 gn H335 with the 69 gn HP that oldfart sold me. Each grain were 2 inch groups of 20 rounds at 100 yards but the 22 gn were tighter. There was some primer flattening at 24 gn but no blow by or cratering. They did seem to eject sky ward past the Caldwell brass collector attached to my AR. The cases don't look too dirty or dented. I'll probably try again next time with the new 55 gn Hornady bullets I bought. They're all the same length unlike those crappy ones I used last week with CFE223.

I did have two misfires out of 100 rounds. I can hear powder inside so I blame the CCI primers. I bought Federal primers so will start to use those next time. I'm wondering if the humidity is getting to the primers.

If you look at the top cases you can see the blow by and excessively flat the primer. 

problem 1.  I didn't work up the load with the new component
problem 2.  I didn't inspect any of the cases per shot, I didn't think it would make any difference.

Lucky for me, and my face, the only thing that happened is I ruined about half my new cases, damaged the ejector spring, and slightly etched my bolt face.  This is in a high end target action, imagine if this was a semi auto,  Might have blown it up.
« Last Edit: January 13, 2017, 09:23:59 PM by rklapp »
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #50 on: January 13, 2017, 09:35:28 PM »
Damn...

I'm surprised the primers didn't blow out with that much blow by.

Today, I shot 20 to 24 gn H335 with the 69 gn HP that oldfart sold me. Each grain were 2 inch groups of 20 rounds at 100 yards but the 22 gn were tighter. There was some primer flattening at 24 gn but no blow by or cratering. They did seem to eject sky ward past the Caldwell brass collector attached to my AR. The cases don't look too dirty or dented. I'll probably try again next time with the new 55 gn Hornady bullets I bought. They're all the same length unlike those crappy ones I used last week with CFE223.

I did have two misfires out of 100 rounds. I can hear powder inside so I blame the CCI primers. I bought Federal primers so will start to use those next time. I'm wondering if the humidity is getting to the primers.

Someone mentioned earlier in the threads that the federal primers aren't the best for small rifle since they are softer. I'm actually buying CCI or a different brand after I get through the brick of Federal I have.

Heavies

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #51 on: January 13, 2017, 10:36:19 PM »
Someone mentioned earlier in the threads that the federal primers aren't the best for small rifle since they are softer. I'm actually buying CCI or a different brand after I get through the brick of Federal I have.
The reason federal are not good is because they are soft and sensitive primer.  They are fine for bolt actions, but for say a semiautomatic with a floating firing pin they could cause the round to ignite by being struck from the bolt closing.  This is called a slam fire.  They are good primers, and many people use them for match accurate rounds, one just runs that risk.

I use CCI military #41 primers in my ARs.  These have hard cup that are designed for running in that type of rifle.  I've also used regular and magnum CCI primers and they have not had any problems. I just use the #41s so I don't have to worry about it.

Never had a CCI primer misfire on me before, I've used bricks.
Only time I have had misfires was with PMC primers.  They are good stuff for small standard deviation and extreme spread though, for a target load I can live with a few duds caps.

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #52 on: January 14, 2017, 03:46:22 AM »
The misfires have been happening towards the end of the CCI brick. Also is happening with the large rifle brick I bought at the same time. Should I be storing them in a zip lock bag? Regardless, I have the Federal brick so will start using those and see if I have similar problems.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #53 on: January 14, 2017, 06:35:41 AM »
Damn...

I'm surprised the primers didn't blow out with that much blow by.

Today, I shot 20 to 24 gn H335 with the 69 gn HP that oldfart sold me. Each grain were 2 inch groups of 20 rounds at 100 yards but the 22 gn were tighter. There was some primer flattening at 24 gn but no blow by or cratering. They did seem to eject sky ward past the Caldwell brass collector attached to my AR. The cases don't look too dirty or dented. I'll probably try again next time with the new 55 gn Hornady bullets I bought. They're all the same length unlike those crappy ones I used last week with CFE223.

I did have two misfires out of 100 rounds. I can hear powder inside so I blame the CCI primers. I bought Federal primers so will start to use those next time. I'm wondering if the humidity is getting to the primers.
I found the burn speed of the H335 with bullets heavier than around 60-65 grains is a little too fast for that weight bullet in the AR platform. For lighter bullets I think that H335 can't be beat. If you have not done so already I would suggest concentrating your efforts using the H335 with lighter bullets like the 55 gr bullets you have.

Those 69 grain Noslers that OF has are awesome bullets. He sold some to me a few years ago, also. They work really well in my AR. I found Varget works really well with bullets 65gr and heavier. And I got much better results using the Varget and those 69gr bullets. I suggest you try a powder that burns a little slower. You will probably get better results with a powder that has a burn rate closer to Varget than H335. You will more than likely get higher velocities and probably tighter groups. I believe you might get better results with the CFE 223 you have with those 69 gr bullets as the burn rate is close to Varget and is in a very good range for heavier bullets. And you might see better results with the H335 and the 55 gr bullets you were trying.

Again this is only a suggestion as these results are what I have seen in my testing and reloading for my AR. Of course your results could be different.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #54 on: January 14, 2017, 10:55:40 AM »
I was happy with the results of the H335 at 100 yards. It will be interesting to see how it compares with the 55 gn bullets. I decided to start making my own targets with 2 inch stickers. At the range, it was really, really bright but seemed to work better than the splatter targets I was using.

I pulled the bullets on the two misfires and one was rather clumpy. Probably didn't allow it to dry long enough after cleaning.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #55 on: January 14, 2017, 11:26:54 AM »
I was happy with the results of the H335 at 100 yards. It will be interesting to see how it compares with the 55 gn bullets. I decided to start making my own targets with 2 inch stickers. At the range, it was really, really bright but seemed to work better than the splatter targets I was using.

I pulled the bullets on the two misfires and one was rather clumpy. Probably didn't allow it to dry long enough after cleaning.
I was pretty happy with the heavier bullets and H335 also. That is until I tried a slower powder. Then the groups tightened right up. I am only making suggestions to you based on my experience. If you are happy with your results no need to try more combinations. I think H335 is one of the best powders for this cartridge so I don't think you'll be unhappy with it. BTW, I use those little orange stickers as well. But I use them on the splatter sighting in targets. Makes being consistent a little easier.  :thumbsup: :thumbsup: :thumbsup:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #56 on: January 14, 2017, 11:29:36 AM »
Think I might have time to squeeze in some bang time early Sunday and see if 27-27.2 is too much for the setup I reloaded.

I'll probably batch out a few at 26 tonight.  :thumbsup:

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #57 on: January 14, 2017, 11:45:47 AM »
I used up the 100 I bought from oldfart but don't intend to get anymore. Last November, I tried 62 gn I bought from WGS with Varget and wasn't good. I was surprised when the 69 gn worked well.

My aging eyes need a little more help as I get older. The prescription for my new glasses is actually weaker than the ones I currently have, but it's the focusing that's becoming more difficult.

Kalen, you might want to fill a couple rounds at 24, 25, and 26 gn just to check for pressure signs as you go up.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #58 on: January 14, 2017, 12:04:07 PM »
I used up the 100 I bought from oldfart but don't intend to get anymore. Last November, I tried 62 gn I bought from WGS with Varget and wasn't good. I was surprised when the 69 gn worked well.

My aging eyes need a little more help as I get older. The prescription for my new glasses is actually weaker than the ones I currently have, but it's the focusing that's becoming more difficult.

Kalen, you might want to fill a couple rounds at 24, 25, and 26 gn just to check for pressure signs as you go up.

Load data I got sent to me out of the hodgdon manual calls for 26-27.8

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #59 on: January 14, 2017, 03:21:58 PM »
So you're using the exact bullet, case, primer, and rifle they use? If not, it's prudent to start lower to make sure, IMHO.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/