For mags, keep an eye on the feedlips and followers.  If you have the W/C with the ETM followers, think you're good there.  I haven't shot my 1911 in a while, but my W/C mags with the ETM follower have been good.  Go ask WTFShane.

I haven't brought it out in a while, so the ETMs haven't seen much use. I was using the 47D before them and had no issues running on 2 different guns (both Springfield).

So prior to taking her to the range, do I clean first?  I YT cleaning vids and I'm not worried about the "idiot mark" as I'm gonna assume it will happen eventually.

So prior to taking her to the range, do I clean first?  I YT cleaning vids and I'm not worried about the "idiot mark" as I'm gonna assume it will happen eventually.

i would clean it first.  in case there is any packing grease to clean off.  I like to run my 1911's lubed pretty good.
as long as you are careful putting back that pin, you can avoid the idiot mark.  the only tricky part about re-assembly is getting that pin through that barrel ring, but its not terribly tricky, actually pretty easy after a few times
if yours comes really tight fit in the barrel bushing area, might need a disassembly tool / bushing wrench to turn the bushing.  one of mine came super tight, but thats how some of the good 1911's are

So prior to taking her to the range, do I clean first?  I YT cleaning vids and I'm not worried about the "idiot mark" as I'm gonna assume it will happen eventually.

I agree with stang.  Depends on how your gun arrives.  Assuming that a production model will have some grease and corrosion protection. 

Another thing to check is the fit of the bushing.  Some 1911s can have a very well fitting bushing.  One of mine can be removed without any tools, and another needed a metal bushing tool.  I had a plastic one and that one didn't cut it. 

I agree with stang.  Depends on how your gun arrives.  Assuming that a production model will have some grease and corrosion protection. 

Another thing to check is the fit of the bushing.  Some 1911s can have a very well fitting bushing.  One of mine can be removed without any tools, and another needed a metal bushing tool.  I had a plastic one and that one didn't cut it.

same here.  I already had a plastic bushing wrench that came with my Ruger 1911.  but didn't work well on the Springfield that needs it.  got a aluminum one that works better

https://www.amazon.com/Pridefend-Aluminum1911-Breakdown-Cleaning-Gunsmithing/dp/B07SC8GVW7/ref=sr_1_6?crid=2FHFFYJLGLYT6&keywords=1911+bushing+wrench&qid=1648670545&sprefix=1911+bushing+%2Caps%2C270&sr=8-6

i think this is the bushing wrench I have

I have the Brownells bushing wrench

https://www.brownells.com/gunsmith-tools-supplies/handgun-tools/barrel-tools/barrel-bushing-tools/1911-anodized-bushing-wrench-prod392.aspx

Can double a bottle opener (kidding)

I haven't brought it out in a while, so the ETMs haven't seen much use. I was using the 47D before them and had no issues running on 2 different guns (both Springfield).

Been shooting other pistolas?  Or not shooting as much?

Unfortunately, I'm in the latter.  Need to get out to the range more with the handguns for range days, matches, training, etc. 

Been shooting other pistolas?  Or not shooting as much?

Unfortunately, I'm in the latter.  Need to get out to the range more with the handguns for range days, matches, training, etc.

WTF been shooting da rolland especial...

WTF been shooting da rolland especial...

brrrrruuuuahhh!  Pancy, pancy, eh!

I like the Agency Arms version for Aaron Cowan.  But who needs another handgun, glock, etc. . . 

So prior to taking her to the range, do I clean first?  I YT cleaning vids and I'm not worried about the "idiot mark" as I'm gonna assume it will happen eventually.

I’ve always field stripped and cleaned any new acquisitions. No sense causing unnecessary wear on a brand new (or even used) toy by shooting it dirty or unlubed with unknowns.


If you’re careful, you’ll avoid the scratch.  I’ve never done it to any of my 1911s. There’s no need to put any downward force on the takedown pin to get it assembled if everything is lined up properly. If force is needed, recheck everything is in place, and try again.

I’ve always field stripped and cleaned any new acquisitions. No sense causing unnecessary wear on a brand new (or even used) toy by shooting it dirty or unlubed with unknowns.

clean and lubed is always preferred 

I’ve always field stripped and cleaned any new acquisitions.

...

That's been my philosophy.  Just like not trusting a gun to be unloaded until you inspect & clear it, never trust a gun you just bought to be properly cleaned and assembled until you've cleaned and inspected/assembled it yourself.

Not only are you making sure the gun is ready for use, you're also familiarizing yourself with it's tear down, assembly, and function.  Doing that before taking it to the range can prevent many user-induced problems.

Who's to say the factory didn't do a quick cursory cleaning and lubing after test firing, only to accidentally put something together wrong?  Or, if it was in a showcase, a customer or employee might have caused a problem.

Your gun -- your responsibility.

Not only are you making sure the gun is ready for use, you're also familiarizing yourself with it's tear down, assembly, and function.  Doing that before taking it to the range can prevent many user-induced problems.

SNIP

WIth the OP, I would put money on "not likely" 

Maybe with hardware issues, but the software? 

 

WIth the OP, I would put money on "not likely" 

Maybe with hardware issues, but the software? 

 

Low left. It must be the gun, ammo, weather, earth not curving, etc...

Low left. It must be the gun, ammo, weather, earth not curving, etc...

You're starting to sound like someone else on 2a. . . :hmm:

clips

You're starting to sound like someone else on 2a. . . :hmm:

clips

Heads

WIth the OP, I would put money on "not likely" 

Maybe with hardware issues, but the software? 

 

Did you mean "operator?"

"Assessment: PEBKAC."

Problem Exists Between Keyboard And Chair

Did you mean "operator?"

"Assessment: PEBKAC."

Problem Exists Between Keyboard And Chair

PEEB

Problem Exists Everywhere Bruh 

So the plan was to not use this for HD, but i bought 2 boxes just in case. Will probably buy more once i know it functions correctly.

Sent from my SM-G991U using Tapatalk