2aHawaii

Tools and Uses => Firearms and Accessories => Topic started by: changemyoil66 on August 26, 2019, 09:43:09 AM

Title: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 09:43:09 AM
My M&P 9C that has about 1500-2K rounds through her has been having failure to fire, about 4 rounds per 50 rd box.

Gun just goes click.  So it is cocked, and tap rack works and next round fire.  Round that didn't fire didn't even have a primer strike.  Tried various ammo.

Cleaned the gun, even the striker channel.  Some said if excess oil/lube gets in there, the problem will happen also.  Still no bang.  And prior to cleaning, gun wasn't even that dirty.

So I did the "pencil" test, but with the inside of a ball point pen instead.  Put the ink casing down the barrel, metal tip side sticking out.  Point the gun in the air and press trigger.  The ink didn't even move.

So I tried the same with my VP9 and the ink flew out about 3 feet high.  You're supposed to use a wooden pencil and eraser side down, but we didn't have one.

I emailed S&W and awaiting response.  I'll replace the striker spring and if the problem happens again, then will send gun  into S&W because it may be something else causing the spring to wear quickly.
Title: Re: Worn Striker Spring
Post by: Flapp_Jackson on August 26, 2019, 09:59:16 AM
Is that the original spring that came with the firearm?

I had similar issues with my G17 when I used the lightest spring (I think 3.5 - 4 lbs) in a pack I received with an upgrade trigger.  Replacing the original spring worked.
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 10:25:56 AM
OG striker spring, but not OG trigger and trigger spring.  Got the Apex trigger in there (purple).
Title: Re: Worn Striker Spring
Post by: Flapp_Jackson on August 26, 2019, 10:32:49 AM
OG striker spring, but not OG trigger and trigger spring.  Got the Apex trigger in there (purple).

Maybe try replacing the trigger & trigger spring if you have the original.  Eliminate variables ....
Title: Re: Worn Striker Spring
Post by: ren on August 26, 2019, 11:17:42 AM
or just get a Glock  :geekdanc:
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 11:27:58 AM
or just get a Glock  :geekdanc:

I was told that by 3 people at the range...
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 11:30:56 AM
Maybe try replacing the trigger & trigger spring if you have the original.  Eliminate variables ....

Don't got the originals.  Dumped it when we moved.  And installing it would be over my pay grade.  The striker spring is within my pay grade.  Did it on my VP9 when I replaced the plastic striker sleeve with a metal one.  Lost 1 side of the C clamp.  Hunted for 45 mins.  Was about to order another one and I found it.  Like I punched in my CC info and everything. 

Next time I'm working on stuff under tension either in the bathroom or inside a ziploc bag.
Title: Re: Worn Striker Spring
Post by: macsak on August 26, 2019, 12:07:00 PM
I was told that by 3 people at the range...

it's called a clue...
Title: Re: Worn Striker Spring
Post by: drck1000 on August 26, 2019, 12:15:37 PM
You mentioned not saying a primer strike. But did you see anything on the rim of the casing? Might be tough to tell on some casing.

A while back, an IPSC/USPSA shooter was having similar troubles during a match with M&P 9 5”. I recall something about the channel or whatever the firing pin rides in was off somehow. Maybe worn, defective  whatever. Anyways, it wasn’t aligning the firing pin properly and he suspected it was missing the primer.

I concur with previous feedback that best bet to revert back to OEM to eliminate variables. OBE for you since you dumped the OEM parts, which you get a :facepalm: badge for. Anyways, was just mentioning something else that I observed with M&Ps.
Title: Re: Worn Striker Spring
Post by: drck1000 on August 26, 2019, 12:16:00 PM
it's called a clue...
Can you pls elaborate  ???  ;D
Title: Re: Worn Striker Spring
Post by: ren on August 26, 2019, 12:29:47 PM
or get a time tested 1911
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 12:53:19 PM
it's called a clue...

heads
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 26, 2019, 12:53:58 PM
or get a time tested 1911

Trading no primer strike to jams...gotta think about that one. :rofl:
Title: Re: Worn Striker Spring
Post by: ren on August 26, 2019, 01:29:54 PM
Trading no primer strike to jams...gotta think about that one. :rofl:

only if you shoot like a girl...
Title: Re: Worn Striker Spring
Post by: Flapp_Jackson on August 26, 2019, 04:02:21 PM
only if you shoot like a girl...

Misogynist!  Sexist!  Patriarchal!

https://en.wikipedia.org/wiki/Tori_Nonaka

(https://i.imgur.com/hA5wtDZ.jpg?1)


https://youtu.be/V-0gYBPcjew
Title: Re: Worn Striker Spring
Post by: drck1000 on August 26, 2019, 04:34:55 PM
only if you shoot like a girl...
From what Macsak says, that might be an improvement.  ;D

I keed. I keed.  :rofl:
Title: Re: Worn Striker Spring
Post by: ren on August 26, 2019, 04:58:48 PM
Misogynist!  Sexist!  Patriarchal!

https://en.wikipedia.org/wiki/Tori_Nonaka

(https://i.imgur.com/hA5wtDZ.jpg?1)


https://youtu.be/V-0gYBPcjew

action shooters can sling lead fast
and she's using a Glock - not surprisingly as she is sponsored.
anyways,
there's more background info on that shooter... :-X
Title: Re: Worn Striker Spring
Post by: Heavies on August 26, 2019, 09:04:11 PM
Maybe the aftermarket trigger doesn't pull the striker back as far as the stock trigger would, before allowing the striker to fall.  That, in conjunction with a weakened striker spring, might be causing the failures to fire. 
Title: Re: Worn Striker Spring
Post by: dogman on August 26, 2019, 09:28:21 PM
or just get a Glock  :geekdanc:
or get a time tested 1911
or . . . revolver
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 27, 2019, 12:33:41 PM
Maybe the aftermarket trigger doesn't pull the striker back as far as the stock trigger would, before allowing the striker to fall.  That, in conjunction with a weakened striker spring, might be causing the failures to fire.

That's my 2nd thought.  So if it happens again, then I gotta look into that.
Title: Re: Worn Striker Spring
Post by: dirtylickins on August 27, 2019, 11:15:11 PM
Put it in the black plastic bag repair resolver.... Then listen to those 3 people's advice on the range O0 and watch other people figure out why there guns don't work and enjoy the comedy :thumbsup:
Title: Re: Worn Striker Spring
Post by: changemyoil66 on August 28, 2019, 09:51:52 AM
S&w sending free striker spring.

Sent from my SM-G950U using Tapatalk

Title: Re: Worn Striker Spring
Post by: Bushido on September 02, 2019, 09:23:28 PM
S&w sending free striker spring.

Sent from my SM-G950U using Tapatalk

Post your resolution.  I "sort of" (half ass) cleaned mine and had 5-6 that the trigger didn't reset in 300ish rounds. Completely tore down the lower and cleaned everything especially the sear block and parts, It was very dirty. Shot 300 without an issue. My striker spring has well over 8K probably more and I'm not even close to thinking about replacing it. Also if you have the Apex flat faced and forward set sear kit, you would have had to have replaced the striker block as part of the install. If so, I do not believe you can remove the striker without removing the rear sight. The striker block was completely redesigned to work with their kit. 
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 03, 2019, 08:56:32 AM
Post your resolution.  I "sort of" (half ass) cleaned mine and had 5-6 that the trigger didn't reset in 300ish rounds. Completely tore down the lower and cleaned everything especially the sear block and parts, It was very dirty. Shot 300 without an issue. My striker spring has well over 8K probably more and I'm not even close to thinking about replacing it. Also if you have the Apex flat faced and forward set sear kit, you would have had to have replaced the striker block as part of the install. If so, I do not believe you can remove the striker without removing the rear sight. The striker block was completely redesigned to work with their kit.

I'll post vids of the pencil test.

I don't remember if we replaced the striker block.  What ever came with the purple Apex trigger kid is what we used.

So we will see if the apex kit is causing wear on the striker spring if the problem happens again.  But won't know for at least a year because I don't shoot the 9c as much.
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 03, 2019, 12:45:19 PM
Yup, just went online and it comes with the striker block.
Title: Re: Worn Striker Spring
Post by: Bushido on September 03, 2019, 07:45:33 PM
Yup, just went online and it comes with the striker block.

It's called a clue.  :rofl: :rofl: :rofl: Had to.
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 04, 2019, 10:19:54 AM
It's called a clue.  :rofl: :rofl: :rofl: Had to.

Biggest clue, buy a Glock.  Does Bushido even own one?  We should do a BOGO sale.
Title: Re: Worn Striker Spring
Post by: Heavies on September 04, 2019, 04:38:07 PM
Biggest clue, buy a Glock.  Does Bushido even own one?  We should do a BOGO sale.

Best course of action would be to dump the strikers altogether.   Get a CZ.  😉😜
Title: Re: Worn Striker Spring
Post by: Bushido on September 04, 2019, 09:25:54 PM
Best course of action would be to dump the strikers altogether.   Get a CZ.  😉😜

I have a soft spot for 1911s but my wallet doesn't agree. Hence striker fired....
Title: Re: Worn Striker Spring
Post by: Bushido on September 04, 2019, 09:28:04 PM
Biggest clue, buy a Glock.  Does Bushido even own one?  We should do a BOGO sale.

Nope. I don't own any firearms, ammunition nor reloading equipment. #Macsak
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 04, 2019, 10:10:42 PM
Nope. I don't own any firearms, ammunition nor reloading equipment. #Macsak
Or body armor

Sent from my SM-G950U using Tapatalk

Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 09, 2019, 08:59:43 AM
So I emailed S&W and asked for a striker spring.  They said they will mail one for free.

But this morning I receive the entire striker assembly.  Great customer service. Now I don't have to worry about taking stuff apart that's under spring tension.

Lost my VP9 striker spring C ring for 45 mins. 
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 12, 2019, 09:44:44 AM
Forgot to take vid before I swapped them out.  Going range this weekend to test.
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 14, 2019, 07:34:05 PM
Gun still no work 100%. Gonna try open the trigger bar loop more.

Sent from my SM-G950U using Tapatalk

Title: Re: Worn Striker Spring
Post by: macsak on September 14, 2019, 07:36:48 PM
Gun still no work 100%. Gonna try open the trigger bar loop more.

Sent from my SM-G950U using Tapatalk

that's called a clue...
Title: Re: Worn Striker Spring
Post by: changemyoil66 on September 14, 2019, 07:57:06 PM
that's called a clue...
No mess with aftermarket trigger. Stock is fine.

Sent from my SM-G950U using Tapatalk

Title: Re: Worn Striker Spring
Post by: Heavies on September 16, 2019, 09:48:21 PM
(https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcRSZuWWKHtTM-1kQRVC_YtUvCT7dy91FIchFEeHUAoz1WieOaqZ)
Title: Re: Worn Striker Spring
Post by: Bushido on September 17, 2019, 02:19:08 PM
Take the lower completely apart and clean it good especially the sear block. Or........................you  could gift the pistol to me. :geekdanc: :geekdanc: :geekdanc: LMK if you like me do it. I'm not a certified S&W Gunsmith but I did stay at a Holiday Inn Express last night. I really am.
Title: Re: Worn Striker Spring
Post by: astroboy on October 27, 2019, 11:14:20 PM
It might be worth a try to do the pencil test while pushing up on the striker block with a small allen wrench thru the rear of the slide.
just my 2 cents
Title: Re: Worn Striker Spring
Post by: changemyoil66 on October 28, 2019, 08:59:24 AM
Update
Send APEX pics and they said the gap between the slide and frame is very big.  So this may be the reason why the tolerances are being messed with. Below is their response.

Your firearm has quite a large slide to frame gap, which I believe is part of the failure to reset issue. If there’s a large space between the slide and frame, that means there’s a larger space (and therefore less contact) between the sear and striker. If the sear bounces slightly under recoil or is slow to return, it may not catch the striker consistently. Our kit includes a heavy sear spring to give the sear a strong return and prevent sear flutter.

 

I am going to send you a replacement sear spring just in case the one you received is on the shorter or lighter side. I am also going to send you an alternate Forward Set Sear. Our 7-Dot Sear is similar to our 3-Dot Sear, but it has a higher tilt to provide more contact with the striker. That way the striker won’t be able to bypass the sear. I do want to give you a heads up that the 7-Dot Sear will increase the trigger pull weight by approximately 1lb. To balance out the trigger pull weight increase, you can re-install your factory trigger return spring. As long as you do not have a state compliant model that comes with a 10lb+ trigger pull weight, your trigger return spring is approximately 0.5-1lb lighter than the silver spring in our kit.
Title: Re: Worn Striker Spring
Post by: Heavies on October 28, 2019, 06:02:06 PM
Update
Send APEX pics and they said the gap between the slide and frame is very big.  So this may be the reason why the tolerances are being messed with. Below is their response.

Your firearm has quite a large slide to frame gap, which I believe is part of the failure to reset issue. If there’s a large space between the slide and frame, that means there’s a larger space (and therefore less contact) between the sear and striker. If the sear bounces slightly under recoil or is slow to return, it may not catch the striker consistently. Our kit includes a heavy sear spring to give the sear a strong return and prevent sear flutter.

 

I am going to send you a replacement sear spring just in case the one you received is on the shorter or lighter side. I am also going to send you an alternate Forward Set Sear. Our 7-Dot Sear is similar to our 3-Dot Sear, but it has a higher tilt to provide more contact with the striker. That way the striker won’t be able to bypass the sear. I do want to give you a heads up that the 7-Dot Sear will increase the trigger pull weight by approximately 1lb. To balance out the trigger pull weight increase, you can re-install your factory trigger return spring. As long as you do not have a state compliant model that comes with a 10lb+ trigger pull weight, your trigger return spring is approximately 0.5-1lb lighter than the silver spring in our kit.

Wholly crap, what states require a 10lb trigger pull?   :crazy:
Title: Re: Worn Striker Spring
Post by: Inspector on October 28, 2019, 06:27:02 PM
Wholly crap, what states require a 10lb trigger pull?   :crazy:
New York?

https://www.thetruthaboutguns.com/ny-democrats-introduce-mandatory-trigger-pull-weight-bill/
Title: Re: Worn Striker Spring
Post by: changemyoil66 on October 28, 2019, 06:54:55 PM
Wholly crap, what states require a 10lb trigger pull?   :crazy:
MA does. But at least they issue ccws. I would take a 10lbs trigger pull and ccw than 1lb and no ccw.

Sent from my SM-G950U using Tapatalk

Title: Re: Worn Striker Spring
Post by: changemyoil66 on October 28, 2019, 10:04:39 PM
See below 7 dot vs 3 dot. Also i added in the 1lb extra spring. I felt the one that i had was to light for ccw carry.

Function test fine. Trigger resets right at the wall. Will keel u guys updated after i put 100rds through her.(https://uploads.tapatalk-cdn.com/20191029/b68ec39b5aa5ed7ff8aed76ba6526639.jpg)

Sent from my SM-G950U using Tapatalk