2aHawaii

General Topics => General Discussion => Topic started by: bushmasta55 on July 13, 2012, 03:23:14 PM

Title: Zeroing in AR
Post by: bushmasta55 on July 13, 2012, 03:23:14 PM
I been trying to zero in my AR yesterday but had a hard time doing it.  It was all over the place maybe due to the wind and maybe not doing the fundamentals of shooting.  What are distances on the rifle side? If I remember correctly zeroing is done at 25 meters.  The type of target I was using was the hoppers bull's eye type, are there any tagets besides the military type that help in zeroing in an AR? 
Title: Re: Zeroing in AR
Post by: drck1000 on July 13, 2012, 03:44:03 PM
I been trying to zero in my AR yesterday but had a hard time doing it.  It was all over the place maybe due to the wind and maybe not doing the fundamentals of shooting.  What are distances on the rifle side? If I remember correctly zeroing is done at 25 meters.  The type of target I was using was the hoppers bull's eye type, are there any tagets besides the military type that help in zeroing in an AR?

At Koko Head, the first row of pipes is at 50 yards.  The one in front of the berm is at 100 yards. 

I have all of my ARs zeroed at 50 yards.  I am not sure what it a "typical" zero, but I mostly hear either 50 yards or 100 yards.  The wind shouldn't have much of an impact at 50 or 100 yards unless it's really blowing out there. 

I use the targets that have grids at 1 inch on-center.  That helps me judge how many clicks of adjustment that I need when viewing through a spotting scope.  Other than that, nothing special.  I do use a Lead Sled when I zero my guns to help eliminate the human variable and get a little finer zero, but you should have no problem zeroing a gun from a rest of from prone with a magazine monopod.  If you don't have a free float rail, be sure you're not putting too much pressure on the handguards if shooting from a front rest. 

When you mean all over the place, how far are you off?  If you're using something like XM855 at 50 or 100 yards, don't expect to get much better than 3-4 MOA groups. 
Title: Re: Zeroing in AR
Post by: bushmasta55 on July 13, 2012, 04:08:53 PM
I was using steel cased rounds MFS brand from SA.
Title: Re: Zeroing in AR
Post by: kia_killer on July 13, 2012, 04:27:38 PM
I like the Shoot N C targets, easy to spot and also have 1" grids to help dialing in. What type of sight were you trying to zero? Were you at least on the page for each shot and just getting poor groupings? How did your ar like the steel case ammo?
Title: Re: Zeroing in AR
Post by: Ichigeki Hissatsu on July 13, 2012, 05:03:14 PM
i need to buy a spotting scope lol.  I have such a hard time zeroing my ar's because i can't see where i'm hitting while looking through my shitty binoculars.  :(
Title: Re: Zeroing in AR
Post by: DuckFat on July 13, 2012, 05:05:53 PM
There's holes at 25 yards on the 2nd and 3rd benches on the far right. I zero rifles at 50 yards because that's where I usually set up my frame.

There are probably better ones out there but I like to use this grid type for zeroing a freshly mounted scope.
http://www.targetprinter.com/grid1.html (http://www.targetprinter.com/grid1.html)

Did you remember to loctite your screws in place?
Title: Re: Zeroing in AR
Post by: Tom_G on July 13, 2012, 05:47:22 PM
If you are hitting "all over the place," the problem is  not with sighting in.  Something else is amiss, whether it be you, the gun, or the ammo. 

Step 1:  look for loose screws, parts, or pieces.
Step 2:  buy 2 other brands of ammo.  Just one box each.  Try in particular to get different weights of bullets.
Step 3:  shoot from a benchrest

The target type is irrelevant, although I prefer large pieces of paper (tabloid size) so I can at least tell when I'm on the paper.  With small targets on well-used cardboard, you may have no idea where you are hitting. 

Take your time, do everything by the numbers, and shoot a 5-round group.  At 50 yards, from the bench, even with open sights, there's no reason you shouldn't have a group that you can cover with the palm of your hand.  Repeat the process with a different brand of ammo and a new, clean target.

If you're getting a buckshot pattern, we're back to the "something is wrong" premise.  Eliminate variables one by one.  Start with what's easy, get rid of yourself.  Ask someone else whose targets look a lot better than yours to give it a try. 
Title: Re: Zeroing in AR
Post by: GZire on July 13, 2012, 06:05:56 PM
I was using steel cased rounds MFS brand from SA.

What is your sighting program?

Do you shoot a group of 5 then adjust?  Do you shoot from a sandbagged front and rear?  Are you using a magnified optic?  How many groups are you putting down range?  Did you have your optic properly set up (rings tight, screws tight, base tight, parralax adjusted)?

Lots of stuff that can go wrong.
Title: Re: Zeroing in AR
Post by: zippz on July 13, 2012, 06:51:53 PM
Make sure your sights are on tight.  I had loose scope once and was wondering why I was so bad at shooting till I noticed.  If it's not the sights, then I'm afraid to say it's most likely just you.  Do what they recommend with the sandbags and get your rifle zeroed then work on your fundamentals.  Once you get a solid zero and group, you can go to Puuloa to get your  600 yard zero :D
Title: Re: Zeroing in AR
Post by: spanner1751 on July 13, 2012, 06:56:21 PM
Set a target at 50 yds with a large white backing (maybe 2X3 feet) with a black circle maybe 6 in. in the center. Then, pick a spot on the berm behind the 100 yd line and shoot at it. That way, you can see the impact of your round in the sand and you can tell where you're hitting. When you're in the ballpark, shoot at the 50 yd target to refine your zero, and finally, take your target out to 100 yds to further refine your zero. 
Title: Re: Zeroing in AR
Post by: SpeedTek on July 14, 2012, 12:03:57 AM
Free zeroing in your scope at X-Ring for 2A members. Saves Ammo....

As long as they not busy.

I wasted 150 rounds of M1 carbine and was all over the paper. Never again. Laser Bore Sight it first!!!
Title: Re: Zeroing in AR
Post by: Jkeone808 on July 14, 2012, 12:27:28 AM
Free zeroing in your scope at X-Ring for 2A members. Saves Ammo....

As long as they not busy.

I wasted 150 rounds of M1 carbine and was all over the paper. Never again. Laser Bore Sight it first!!!

Might have to take you up on that  :shaka:
Title: Re: Zeroing in AR
Post by: DuckFat on July 14, 2012, 12:41:31 AM
Free zeroing in your scope at X-Ring for 2A members. Saves Ammo....

As long as they not busy.

I wasted 150 rounds of M1 carbine and was all over the paper. Never again. Laser Bore Sight it first!!!
Zero as in actual zero on targets or just laser bore sighting?
Title: Re: Zeroing in AR
Post by: Colt808 on July 14, 2012, 05:01:31 AM
If you are hitting "all over the place," the problem is  not with sighting in.  Something else is amiss, whether it be you, the gun, or the ammo. 

Step 1:  look for loose screws, parts, or pieces.
Step 2:  buy 2 other brands of ammo.  Just one box each.  Try in particular to get different weights of bullets.
Step 3:  shoot from a benchrest

^^^This^^^

It's not a sighting in problem, but the ammo (MFS .223 55gr).  Don't use cheap plinking/range ammo for sighting/zeroing...It's a mistake a lot of people make. If you sight in with decent quality ammo (that the barrel is chambered for), you will get consistency necessary to properly sight in.



Title: Re: Zeroing in AR
Post by: SpeedTek on July 14, 2012, 06:37:48 AM
Zero as in actual zero on targets or just laser bore sighting?

Ok well laser bore sight. Get u on paper.
Title: Re: Zeroing in AR
Post by: bushmasta55 on July 14, 2012, 07:59:13 AM
Thanks for the input guys. My gun cycles the ammo just fine
Title: Re: Zeroing in AR
Post by: bushmasta55 on July 14, 2012, 08:09:22 AM
What is your sighting program?

Do you shoot a group of 5 then adjust?  Do you shoot from a sandbagged front and rear?  Are you using a magnified optic?  How many groups are you putting down range?  Did you have your optic properly set up (rings tight, screws tight, base tight, parralax adjusted)?

Lots of stuff that can go wrong.

Sorry to mention it guys I'm just zeroing in the iron sights.  I shoot 3 rounds then adjust from that.
Title: Re: Zeroing in AR
Post by: Teichi on July 14, 2012, 08:53:59 AM
The twist rate of the rifling is a concern. 1:12 twist rate should only use bullet weights of 55gr or lighter. 1:9 twist rates should be able to use bullets up to 69gr, but I have seen some barrels that could not stabilize bullets of that weight. 1:7 and 1:8 are optimum for bullets in the 62gr to 90gr weight, but should not be used for light varmint bullets weighing less than 55gr as core and jacket separation may occur while the bullet is travelling down the barrel. The rule of thumb is to stick with 1 type of ammo for the distance you intend to shoot.

If your marksmanship fundamentals are lacking, try to find help from the ROs.
Title: Re: Zeroing in AR
Post by: Tom_G on July 14, 2012, 11:01:40 AM
Thanks for the input guys. My gun cycles the ammo just fine


It's not a question of the gun cycling or not.  It's a question of whether the barrel is stabilizing the bullet.  As Techi says, there is a relationship between the barrel's rifling, the bullet's weight, and the bullet's velocity.  The fact that your gun cycles ammo has absolutely nothing to do with whether it is accurate with that same ammo. 
Title: Re: Zeroing in AR
Post by: bushmasta55 on July 14, 2012, 11:45:27 AM
What is the twist rate for a bushmaster
Title: Re: Zeroing in AR
Post by: Pit808 on July 14, 2012, 12:00:30 PM
What is the twist rate for a bushmaster

Pretty sure its 1:9 for the m4 type barrels

If u are zeroing irons at 50 and aren't grouping with 55gr ammo, I'd let a another ar owner give it a shot. Or you shoot a buddy's zeroed ar. If ur sights are on right, I'm thinking your sight picture is not consistent.  If you are experienced with AR irons then you could: do a quick bullet test / check crown, try different ammo, check barrel nut torque....

 :shaka:

BTW, if using a2 rear I use 55g fmj and Improved battle sight zero for 50yds.  works great.
Title: Re: Zeroing in AR
Post by: Tom_G on July 14, 2012, 12:02:16 PM
According to the website, their barrels are all either 1:9 or 1:8.  Both are intended for heavier bullets.
Title: Re: Zeroing in AR
Post by: ImKu on July 14, 2012, 02:58:48 PM
What type of BUIS are you using? Not sure if this has anything to do with the issue your having but I zeroed my Magpul sights and they were way off out the box, about 6 to 8" high.
Title: Re: Zeroing in AR
Post by: 230RN on July 14, 2012, 04:56:53 PM
I sympathise.  I tried to sight my M4gery in using the regular "carry handle" sights and the regular military instructions for the M4 --run base down to zero elevation, move up to thus-and-so markings, blah blah blah.

No go.

I finally broke down and put a scope on it.

No wonder they call them "BUIs"  --"Back-Up iron sights."



However, I have little love for the AR platform, so maybe there were unconscious negative factors operating.  I only bought one to see what all the fuss was about.  I especially dislike the way the front sight operates.  Shloppier than sh.  So is the rear sight.  Go ahead, wiggle them.  You'll see.

I had to get an extended front sight post to bring it anywhere near the zero required, since DPMS put an AR Rifle front sight on the carbine barrel.  Jeeze, didn't anyone learn basic geometry at DPMS? However, apparently a lot of mfrs do that, which is why they sell extended front sight posts in the first place.

I'm not signing this one so nobody will know who posted it.
Title: Re: Zeroing in AR
Post by: 42itus on July 14, 2012, 07:10:13 PM
Free zeroing in your scope at X-Ring for 2A members. Saves Ammo....

As long as they not busy.

I wasted 150 rounds of M1 carbine and was all over the paper. Never again. Laser Bore Sight it first!!!

Took advantage of your offer.  Thanks X-Ring!
Title: Re: Zeroing in AR
Post by: bushmasta55 on July 14, 2012, 07:41:04 PM
Thanks for the input guys.  I'm planning to the range to re zero my AR, let me know if anyone wants to meet up. 
Title: Re: Zeroing in AR
Post by: SpeedTek on July 14, 2012, 11:58:18 PM
What is the twist rate for a bushmaster

can be anything.  Look at the top front of the barrel should be stamped on there......
Title: Re: Zeroing in AR
Post by: GZire on July 16, 2012, 08:58:22 AM
Sorry to mention it guys I'm just zeroing in the iron sights.  I shoot 3 rounds then adjust from that.

I would suggest moving to a 5 shot pattern before adjusting.  Make sure you sandbag both the front and rear of the rifle. 

Other than this, it's tough to figure out what the issue is unless you have a specific plan you go with to sight in.  Also you have the manufacturer of the ammo listed?/bullet weight?
Title: Re: Zeroing in AR
Post by: Ichigeki Hissatsu on July 16, 2012, 10:41:26 AM
Free zeroing in your scope at X-Ring for 2A members. Saves Ammo....

As long as they not busy.

I wasted 150 rounds of M1 carbine and was all over the paper. Never again. Laser Bore Sight it first!!!

Haha i might have to take them up on that too.  Not having a spotting scope sucks.  When i first sighted in my ar, it took like 20 shots before i saw a single hole on my target.  Then when i went to check it, there were holes all over, but i couldn't see it with my shitty bino's.  :(
Title: Re: Zeroing in AR
Post by: drck1000 on July 16, 2012, 11:11:27 AM
Haha i might have to take them up on that too.  Not having a spotting scope sucks.  When i first sighted in my ar, it took like 20 shots before i saw a single hole on my target.  Then when i went to check it, there were holes all over, but i couldn't see it with my shitty bino's.  :(

A decent spotting scope is key in sighting in, unless you a private range all to yourself where you can check the target after each string.  Even then, I would still use a spotting scope since I am WAY too lazy to walk back and forth that many times. 

You can always boresight by looking down the barrel as long as you have a stable base to support the upper.  I have a decent laser bore sighter, but my condo is so small that I just get ok results from it.  I could use the hallway, but my neighbors probably wouldn't like coming out of their unit with a laser on them and looking up and seeing the barrel of a gun. 
Title: Re: Zeroing in AR
Post by: Heavies on July 16, 2012, 06:06:12 PM
I do an initial bore sighting in my hallway. About 15 yards long.  Use a black circle.  Select a diameter that appears to fill 1/2 of the bore when you look through. Have the upper secured some way so it doesn't move. Then position your head in the same place the stock would be and adjust your sights to your prefferd hold, 6 o'clock, center, or what ever. Just make sure your sights are aligned and looking through the bore. You can do this with an optic sight as well. Don't cheat by moving your head around to line up the sights. Adjust the with your noggin in the same place it would be as if the stock was attached.  Next thing, go on the internet and print out a target circle, with an aiming black, about 5.5-6" in diameter, or get some shoot and see targets if you have a hard time seeing the hits. Also, put it on a brand new cardboard with no holes in it.  That will make this task a hundred times more easy.  Take it out to the range and place it at 50 yards. Crack open the back pin, open up the upper, and sight through the bore with the rifle well supported.  Center up the black in the bore, the sights should be pretty close already. If not make minor adjustments.
Find out and know how much 1 click value is worth on your sights. That means if your irons are 1MOA per click, that will translate to 1/2" at 50 yards, or 1" @ 100,  2" @200, etc.
At this point you should be on paper and you can find tune your sights with 3 round groups.

If you are not on paper something is wrong with the gun, sights, ammo, or that nut that is behind the butt stock may be loose.

I have never used a bore sighter, and have had great success using this method. As long as you can see down the bore, you should have no problem sighting in.
Title: Re: Zeroing in AR
Post by: SpeedTek on July 16, 2012, 06:19:48 PM
I used the bushnell laser bore device on a customers ar and took it to the range sunday. The gun was not even broken in. In fact it was her maiden voyage. All shots were dead on at 100 yards.

One thing i learned about the bushnell is you have to screw it all the way down. We checked this in a lathe and it was perfect at 50'

When i first got it i was rotating it in the bore and it was moving up and down 1" at 30'. It was my fault since i was stopping as soon as the laser went on.

At the shop we can only sight it in at 25' but we do it free so you get what you pay for? But so far everyone said we were close enough.