white mold on guns (Read 5442 times)

ren

white mold on guns
« on: February 17, 2020, 01:52:59 PM »
Any of you experience this as well? I have 2 passive dehumidifiers and a plug in one I use sometimes. I dont know whats causing it. I find it on the wood stocks and plastic grips on ARs too.
Deeds Not Words

zippz

Re: white mold on guns
« Reply #1 on: February 17, 2020, 02:37:35 PM »
I haven't experienced it, but perhaps your Goldenrod or other device can't keep up with the humidity.  They basically raise the temperature in the safe to bring down the % of relative humidity but not the amount of water inside.  Mold starts growing at 60% relative humidity.

So if it's 90% humidity outside the goldenrod may drop it down to like 70%.  Or if the outside temperature later cools down a lot overnight, then relative humidity % of the air trapped in the safe would rise.

I'm guessing you don't run the air conditioner in the room with the safe.

Flapp_Jackson

Re: white mold on guns
« Reply #2 on: February 17, 2020, 02:52:42 PM »
2 tips:

1.  If you don't have a monitoring device inside the safe that at least reports on humidity and temperature, get one.  Mine alerts me to the door opening and closing, excessive humidity and temperature, loss of Internet access, remaining % of battery power, and motion.

2.  Use something that absorbs moisture from the air so you can remove it from the safe interior.  I use DampRid.  Costco has the self-contained hang-up versions that you unwrap, hang up, and throw away when used up.  I also have a few refillable DampRid containers.  Those require emptying, cleaning and refilling. 

The Goldenrod "dehumidifier" simply keeps the interior of the safe warmer than the exterior, which reduces condensation.  It doesn't change the humidity level.  It just tries to prevent the existing water vapor inside the safe from liquefying into drops of water which can then invite mold growth.

Mold is only one impact of high humidity.  The other, of course, is rust.  It pays to remove the moisture, not just keep it from condensing.

The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

macsak

Re: white mold on guns
« Reply #3 on: February 17, 2020, 03:19:25 PM »
2 tips:

1.  If you don't have a monitoring device inside the safe that at least reports on humidity and temperature, get one.  Mine alerts me to the door opening and closing, excessive humidity and temperature, loss of Internet access, remaining % of battery power, and motion.

2.  Use something that absorbs moisture from the air so you can remove it from the safe interior.  I use DampRid.  Costco has the self-contained hang-up versions that you unwrap, hang up, and throw away when used up.  I also have a few refillable DampRid containers.  Those require emptying, cleaning and refilling. 

The Goldenrod "dehumidifier" simply keeps the interior of the safe warmer than the exterior, which reduces condensation.  It doesn't change the humidity level.  It just tries to prevent the existing water vapor inside the safe from liquefying into drops of water which can then invite mold growth.

Mold is only one impact of high humidity.  The other, of course, is rust.  It pays to remove the moisture, not just keep it from condensing.

Costco has the ones you plug in and it r]dries them out, then you unplug and put them back in...

macsak

Re: white mold on guns
« Reply #4 on: February 17, 2020, 03:20:08 PM »
Any of you experience this as well? I have 2 passive dehumidifiers and a plug in one I use sometimes. I dont know whats causing it. I find it on the wood stocks and plastic grips on ARs too.

perhaps the white sticky stuff is not mold...

Flapp_Jackson

Re: white mold on guns
« Reply #5 on: February 17, 2020, 03:35:57 PM »
Costco has the ones you plug in and it r]dries them out, then you unplug and put them back in...

I've tried those in the past.  They don't remove nearly as much moisture as DampRid products.

Those are basically reusable desiccants with plug-up electric drying versus putting them in the oven.
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Platinum808

Re: white mold on guns
« Reply #6 on: February 17, 2020, 03:55:51 PM »
perhaps the white sticky stuff is not mold...
What can it be? O0 :rofl: LGBQ secretions
Oh ignorant youth, the world is not a joyous place. The time has come for you to dispense with the frivolous pleasures of childhood and get down to honest toil until you are sixty-five. Then and only then can you relax and collect your social security and live happily until the time of your death!

-Hunter S. Thompson

zippz

Re: white mold on guns
« Reply #7 on: February 17, 2020, 04:27:20 PM »
I've tried those in the past.  They don't remove nearly as much moisture as DampRid products.

Those are basically reusable desiccants with plug-up electric drying versus putting them in the oven.

Yup big difference.  I used damprid before and I think it lasted for 2 months before I had to refill it.  It held about 1 1/2 to 2 cups of water.  I bought the plug in rechargable and it only lasts a couple weeks or less.  Not worth the hassle of constantly recharging it.  I'm going back to damprid.

ren

Re: white mold on guns
« Reply #8 on: February 17, 2020, 05:52:05 PM »
2 tips:

1.  If you don't have a monitoring device inside the safe that at least reports on humidity and temperature, get one.  Mine alerts me to the door opening and closing, excessive humidity and temperature, loss of Internet access, remaining % of battery power, and motion.

2.  Use something that absorbs moisture from the air so you can remove it from the safe interior.  I use DampRid.  Costco has the self-contained hang-up versions that you unwrap, hang up, and throw away when used up.  I also have a few refillable DampRid containers.  Those require emptying, cleaning and refilling. 

The Goldenrod "dehumidifier" simply keeps the interior of the safe warmer than the exterior, which reduces condensation.  It doesn't change the humidity level.  It just tries to prevent the existing water vapor inside the safe from liquefying into drops of water which can then invite mold growth.

Mold is only one impact of high humidity.  The other, of course, is rust.  It pays to remove the moisture, not just keep it from condensing.

Idea hit me for a Photon IoT board that I have.  :thumbsup:
Deeds Not Words

robtmc

Re: white mold on guns
« Reply #9 on: February 17, 2020, 07:21:48 PM »
I got one of those plug-in devices that extracts the water from the air and collects it in a little container.  Always had a goldenrod in the safe, but as noted, they do not remove the moisture.   A small humidity indicator I gather is usually used by cigar fans for monitoring % humidiy in humidors suffices for an inciation.  Always less than 50% so far.   On a tip to make them last longer, put it on a timer to run in the afternoon.  Apparently, it was claimed they lose the ability to extract water over time so I limit the daily run time to about 4 hours.  They pump out a bit of warm air exhaust.  Inside a safe, I certainly cannot hear anything and the interior is warm from the goldenrod anyway.

Wife likes to hang those damp rid bag things around.  Had one leak and make a mess outside the safe, would never trust one inside.  She had major mold problems in a curio cabinet and now uses one of those rechargeable passive ones along with a humidity meter.

https://www.amazon.com/Pro-Breeze-Electric-Dehumidifier-Portable/dp/B01DC5PPWM/ref=sxin_3_osp129-574b5576_cov?ascsubtag=574b5576-d334-4b6a-8c71-1571c260d4b5&creativeASIN=B01DC5PPWM&crid=2BOZL5KK07EPW&cv_ct_cx=dehumidifier+for+gun+safe&cv_ct_id=amzn1.osp.574b5576-d334-4b6a-8c71-1571c260d4b5&cv_ct_pg=search&cv_ct_wn=osp-search&keywords=dehumidifier+for+gun+safe&linkCode=oas&pd_rd_i=B01DC5PPWM&pd_rd_r=95582ebe-462c-4437-a968-ee87c10197ea&pd_rd_w=xbuqT&pd_rd_wg=JbZ99&pf_rd_p=62c00474-6fe0-420f-9956-a05256e04b43&pf_rd_r=4971NQMJ1G272RB0V1MG&qid=1582003266&sprefix=dehumidifier%2Caps%2C393&sr=1-3-32a32192-7547-4d9b-b4f8-fe31bfe05040&tag=thedrive09-20
« Last Edit: February 17, 2020, 07:29:39 PM by robtmc »

zippz

Re: white mold on guns
« Reply #10 on: February 17, 2020, 07:42:17 PM »
I also bought a roll of cheap stick on gasket to seal the safe door.  Also covered up the wire and bolting holes.  Figured the descant would last longer.

robtmc

Re: white mold on guns
« Reply #11 on: February 17, 2020, 07:59:16 PM »
I also bought a roll of cheap stick on gasket to seal the safe door.
Yeah, had some gray foam tape left over from sealing up window screens and applied that to the safe door to minimize air transfer.   

Did it when i got the moisture sucker, so no idea how much it helped seal things.  i do feel better though.  Only get a few ounces of water in the container each week, so something is limiting the water in the safe.  Do not leave the door open any longer than needed, of course.

drck1000

Re: white mold on guns
« Reply #12 on: February 18, 2020, 12:42:06 PM »
Damn, do you live on or near the water?  I have used damp rid in the past, but mostly use the plug-in ones lately.  My safe is in a room that has an A/C running at least for a portion of the night, so I think that brings the humidity down on average, but I haven't noticed much corrosion.  My REM 700 (OEM barrel and Leupold rings and base) did show signs of light corrosion, but a wipe with Ballistol before storing and haven't seen that again. 

First I've heard of damp rid leaking, but not surprised.  They did seem quite effective though.  I also have the hygrometer for my humidors, but never thought to use one for my safe.  I have an extra one that I might throw in my safe to see the difference between the humidity in my safe and the room the safe it in. 

Flapp_Jackson

Re: white mold on guns
« Reply #13 on: February 18, 2020, 02:09:16 PM »
Based on alerts my safe monitor sends me, when it's raining for 2 days, the humidity in the safe goes way up, especially if the DampRid is close to needing replacement.

I seem to get the alert when I'm too busy to take care of it immediately, too.   :wtf:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

mrgaf

Re: white mold on guns
« Reply #14 on: February 18, 2020, 04:51:18 PM »
I had that problem about 4 years ago. All my oiled wood stocks had it, especially the butt stocks. I’d wipe it off, oil the stocks up with furniture oil and in about 2 months it would come back. I had damp rid (still do), golden rod, etc etc. but it still came back. My safe has “carpeted walls, top, bottom and shelves so I removed everything from the safe and scrubbed the all the carpeted areas with a mixture of 20% white vinegar, 80% water and two or three drops of dawn in a spray bottle. Left the safe open with a fan blowing into it until dry then used resolve carpet cleaner and a scrub brush all over the place. Let it dry, vacuumed everything and left it open for 1 day. Put all the goodies back in powered up the golden rod and damp rid. Since doing that I’ve had zero mold on anything in the safe since.  :shaka:
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

tillamook

Re: white mold on guns
« Reply #15 on: February 19, 2020, 11:37:12 AM »
Does the mold not grow on anything here?  So far I've seen in grow on leather, wood (particle board in particular), cast iron, glass, ceramic, multiple types of plastic.  I have a few anti-corrosion vacuum bags and I've seen white mold grow inside them after still being vacuum sealed.   I had some tums sealed in a plastic bottle inside a zip lock bag grow mold.   

The only thing that hasnt grown mold is this old czech military parka I have.   I got it out when it hit 50F here and it was in pristine shape.  What ever the czechs treated their military gear with is great.  Looked a little dumb with a military green parka with shorts and slippas but it was cold!

ren

Re: white mold on guns
« Reply #16 on: February 22, 2020, 09:45:46 PM »
I got one of those plug-in devices that extracts the water from the air and collects it in a little container.  Always had a goldenrod in the safe, but as noted, they do not remove the moisture.   A small humidity indicator I gather is usually used by cigar fans for monitoring % humidiy in humidors suffices for an inciation.  Always less than 50% so far.   On a tip to make them last longer, put it on a timer to run in the afternoon.  Apparently, it was claimed they lose the ability to extract water over time so I limit the daily run time to about 4 hours.  They pump out a bit of warm air exhaust.  Inside a safe, I certainly cannot hear anything and the interior is warm from the goldenrod anyway.

Wife likes to hang those damp rid bag things around.  Had one leak and make a mess outside the safe, would never trust one inside.  She had major mold problems in a curio cabinet and now uses one of those rechargeable passive ones along with a humidity meter.

https://www.amazon.com/Pro-Breeze-Electric-Dehumidifier-Portable/dp/B01DC5PPWM/ref=sxin_3_osp129-574b5576_cov?ascsubtag=574b5576-d334-4b6a-8c71-1571c260d4b5&creativeASIN=B01DC5PPWM&crid=2BOZL5KK07EPW&cv_ct_cx=dehumidifier+for+gun+safe&cv_ct_id=amzn1.osp.574b5576-d334-4b6a-8c71-1571c260d4b5&cv_ct_pg=search&cv_ct_wn=osp-search&keywords=dehumidifier+for+gun+safe&linkCode=oas&pd_rd_i=B01DC5PPWM&pd_rd_r=95582ebe-462c-4437-a968-ee87c10197ea&pd_rd_w=xbuqT&pd_rd_wg=JbZ99&pf_rd_p=62c00474-6fe0-420f-9956-a05256e04b43&pf_rd_r=4971NQMJ1G272RB0V1MG&qid=1582003266&sprefix=dehumidifier%2Caps%2C393&sr=1-3-32a32192-7547-4d9b-b4f8-fe31bfe05040&tag=thedrive09-20

they sell that at the NEX. Great reviews. Picked up the larger one next to it. Got a humidity meter as well. Shows about 52% right now with the dehumidifier running outside the safe door. I did as mentioned - sprayed vinegar with alcohol. Dried. Took everything out and wiped it all done. Oiled.
Deeds Not Words

Rocky

Re: white mold on guns
« Reply #17 on: February 23, 2020, 09:48:27 AM »
 :crazy:
« Last Edit: February 23, 2020, 09:58:25 AM by Rocky »
“I ask you to judge me by the enemies I have made.”
                                                           Franklin D. Roosevelt

Rocky

Re: white mold on guns
« Reply #18 on: February 23, 2020, 09:58:02 AM »
Moisture in a safe, particularly a fire proof safe is a given.
Condensation occurs when there is a large temperature difference between an object and the atmosphere.
A cool night followed by a hot day will cause condensation as the heavy metal safe retains coolness inside while the exterior heats up.
A safe "full" of cooled items (metal ammo boxes full of lead and brass) compounds the issue.

A fireproof safe is even worse as the "fire proofing" components are usually cement or a drywall type material, both of which absorb moisture.
(If you read the instructions for your fireproof safe, it informs you of this and recommends you open and "air out" your fireproof safe on a regular basis.)

So theoretically, the best case scenario would be to limit temperature differences in your "safe space" by keeping the safe and its surrounding area the same temp like drk1000 does by having controlled room temp via A/C.  :geekdanc:
“I ask you to judge me by the enemies I have made.”
                                                           Franklin D. Roosevelt