Newbie and wants to get into reloading. (Read 18107 times)

wirecounter

Re: Newbie and wants to get into reloading.
« Reply #20 on: May 21, 2012, 10:16:13 PM »
Dang!  All this talk is making me seriously consider getting a single stage press & take my ARness to the next level.

And, I never considered the effect of the lube that gets in the case and affect powder burn - thanks Inspector.   :shaka:  I think . . . LOL

Heavies

Re: Newbie and wants to get into reloading.
« Reply #21 on: May 22, 2012, 02:48:02 AM »
Heavies, thanks for your comments. I was just reading some information last night that said exactly what you said here about the seating depth and the case volume. I'll pursue this route rather than weighing the bullets as you said. This just saved me a lot of hours finding out that there is going to be little or no difference for 100yds. They also mentioned certain powders with particular burn rates for certain length barrels. Which would also affect barrel tune.

As you can tell this is my first attempt at reloading for a rifle. And I am learning as I go along what works for my rifle and what doesn't. I'll look into the book you recommended as it is amazing that you can group like that with 25 rounds. Obviously it has taken me hundreds of rounds to get where I am right now.

Thanks again for your help! This sort of stuff makes reloading much more enjoyable!  :shaka:

Not a problem.  I too have fired thousands of rounds before I found the OCW.  Also, once you find the right charge for one weight bullet, you'll know about where you need to be if you wanted to try out another weight bullet, using the same powder.

Of course I have been using this method for a while now so I know what exactly to look for.  And I had a load for another weight bullet so I needed not load too light and waste rounds finding the pressure spot.  Starting fresh with a all new rifle,  new powder, new case, new projectile will necessitate more rounds to look for the max charge/pressure allowable with that rifle.

Also, when using OCW method, key is to shoot the 3 round groups in a 'round robin' sequence, and don't try to rush the process by loading up too many rounds to test, you want all individual shots on call and well aimed at the aiming point.  This will net the most usable data. 

I need to learn from you. How can I compensate you for your time?

No need for that.  Just read up on OCW and also read up a lot on accurateshooter.com.  There is tons of knowledge there, many world class benchrest, f-class, prone, and XTC shooters read and post on that site.

Inspector

Re: Newbie and wants to get into reloading.
« Reply #22 on: May 22, 2012, 06:26:47 AM »
Not a problem.  I too have fired thousands of rounds before I found the OCW.  Also, once you find the right charge for one weight bullet, you'll know about where you need to be if you wanted to try out another weight bullet, using the same powder.

I have been doing exactly this. My best load was worked up with a Berger 64gr Varmint/Target bullet. So I have been trying Sierra 63gr and 65gr bullets. Not quite as tight as the Berger but it didn't take much to get the best charge figured out. Also, since I also know the approximate fps I need for a particular bullet I have been pretty successful working up a similar load with a different powder.

Of course I have been using this method for a while now so I know what exactly to look for.  And I had a load for another weight bullet so I needed not load too light and waste rounds finding the pressure spot.  Starting fresh with a all new rifle,  new powder, new case, new projectile will necessitate more rounds to look for the max charge/pressure allowable with that rifle.

Also, when using OCW method, key is to shoot the 3 round groups in a 'round robin' sequence, and don't try to rush the process by loading up too many rounds to test, you want all individual shots on call and well aimed at the aiming point.  This will net the most usable data. 

I have been using 5 round groups shot twice and averaged. So I have been doing WAY too much work here.

Have you noticed a large difference between primers? I have both Federal SRP and Federal Match SRP and I have not tried to test them for any difference yet.

Thanks again! This is much appreciated.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Heavies

Re: Newbie and wants to get into reloading.
« Reply #23 on: May 23, 2012, 04:02:45 AM »
I have been doing exactly this. My best load was worked up with a Berger 64gr Varmint/Target bullet. So I have been trying Sierra 63gr and 65gr bullets. Not quite as tight as the Berger but it didn't take much to get the best charge figured out. Also, since I also know the approximate fps I need for a particular bullet I have been pretty successful working up a similar load with a different powder.

I have been using 5 round groups shot twice and averaged. So I have been doing WAY too much work here.

Have you noticed a large difference between primers? I have both Federal SRP and Federal Match SRP and I have not tried to test them for any difference yet.

Thanks again! This is much appreciated.

So far I have only tried CCI 200 and PMC large rifle primers for the LR category.  The PMC gave the least velocity spread, accuracy was very similar between the two, thus I have been using PMC for a while now.  Small rifle I have tried CCI 450 and Wolf small rifle magnum .  Again Wolf gave less velocity spread, however accuracy didn't seem to be on par with the CCI small rifle magnum primers.

I have not really gone into testing too many different primers, but I have read that many use the Russian primers for accuracy.  Also many swear by federal primers, but I have stayed away from them due to the sensitivity issues that they may or may not have.  I didn't want them going off in my press while trying to seat them.  Haha. ;D

bparages

Re: Newbie and wants to get into reloading.
« Reply #24 on: November 07, 2012, 05:11:05 PM »
Hey, the lee challenger reloading kit is great for beginners..single stage press, hand primer, powder measurer, scale, just add powder and dies.  Additional musts are caliper, digital scale with standard weight, case holder and cutter, length gauge per caliber. Simple to use with a drill. Case chamfer tool and primer pocket cleaner  by lee  are cheap and useful. You'll enjoy making ur own ammo... But always refer to an up to date reloaders manual, start at starting loads, work up cautiously.. Pay attention to your cases, deformities, cracks, etc.. Have fun.. Single stage Set up gets me about 200 rds an hour..