Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - smashpwnage

Pages: [1]
1
General Discussion / Re: "I am going to the range today"
« on: June 14, 2019, 08:51:39 PM »
just finished a new AR build, and want to test it out. will there be open stalls with the fair happening this weekend?
2
General Discussion / Re: 80 Percent lower registration.
« on: February 06, 2019, 08:56:57 PM »
You did it the best way possible. Bring in a stripped lower and register as pistol. Did you give a barrel length or caliber? How did you fill the form out?

As long as they don't legally define it, they can't legally enforce it. What constitutes detachable? Its subjective and the error is on your (our) side. They have to prove it is not detachable and there are plenty of current legal definitions in the firearms laws across the country to be on our side (not that there should be any requirement for detachable). If they push the mag release and it doesn't come out, its not detachable. If they have to use a tool or disassemble the firearm to remove the magazine, it's not detachable. Anytime they tell you to weld it, they are providing legal advice on behalf of HPD and are at risk of being held liable for themselves and the department. But that's their call, I'm not their boss. And they keep using the term FIXED. The terminology in the HRS is DETACHABLE. Very different legal definitions.



i said i was going to go 10.5", although i really don't know what i'm going to put on it yet since i dont have any other parts for the build.

since it was relatively easy to register this lower, i was thinking about doing a glock 80. should it be the same process? i didn't take the handgun class.
3
General Discussion / Re: 80 Percent lower registration.
« on: February 06, 2019, 08:51:29 PM »
Was the 80% complete ?
Did you have a permit ?

i have a long gun PTA. the stripped lower was made from a 80% and was machined and serialized
4
General Discussion / Re: Brazil gets it
« on: January 30, 2019, 07:41:37 PM »
Will be interesting to see how this one plays out.

we have data already. there was a gun buy back as well as gun reform laws in brazil in the early 2000's. crime rate skyrocketed after
5
General Discussion / Re: 80 Percent lower registration.
« on: January 30, 2019, 06:27:30 PM »
No
The process to acquire the lower to build as a pistol would be the same as a handgun, three trips to HPD.

i just brought in my stripped 80% lower in and registered it as a pistol this morning. after playing 21 questions with the officers for a while they finally registered it.  they were adamant about me bringing it back once its built, and that epoxying the mag into the receiver is not a sufficient way of fixing the magazine. i just said ok and left. i could not find any requirements on fixing magazines and if epoxy is good enough.
6
General Discussion / Re: 80% registration?
« on: January 30, 2019, 06:20:12 PM »
i just registered a stripped 80% lower this morning as a pistol. did not need to wait 2 weeks or need a pistol permit to acquire.
7
General Discussion / Re: 80 Percent lower registration.
« on: January 25, 2019, 06:14:56 PM »
Make an AR pistol.
Check the other post on AR pisto

necro post, i know. is my long gun permit sufficient if i want to register a stripped lower as a pistol lower?
8
Legal and Activism / Re: Assualt Pistol Flow Chart
« on: August 17, 2018, 01:40:36 PM »
yes
 pistol with 30rd magazines have been made, stay with the 20rd mags as they are easier to clean.

i've searched and seems like there is no definition for "detachable". how permanent does the magazine need to be? would a bullet button filled with epoxy work?
9
Legal and Activism / Re: Assualt Pistol Flow Chart
« on: August 16, 2018, 03:59:10 PM »
yes

Hawaii state law prohibits greater than 10 round detachable pistol magazines (including rifle magazines capable of use in any pistol, such as the AR-15/M16, AK, M1 carbine, H&K carbine, Thompson, and aftermarket Ruger .22 magazines) unless blocked to hold 10 rounds or less and “not readily restorable.” Possession of illegal magazines is a misdemeanor, one count per magazine, and possession of a handgun with one inserted is a class C felony. There is much debate among gun owners, law enforcement, and dealers over the interpretation of this portion of the statutes when rifle magazines which fit handguns are considered, and the prohibition is generally not enforced.

so, could i attach a mag greater than 10 round cap?
10
Firearms and Accessories / Re: New AR Pistol barrel w/o ports
« on: August 16, 2018, 03:40:49 PM »
Just put a bullet button and your good to go.  I have asked both HPD and the AG, HPD says they dont have a definition. So anything the guy at the counter tells you is BS, The AG says they have not provided a defintion to HPD.

detachable is different to serviceable.  The engine in your car is not detachable , BUT if you undo some bolts you can remove it to service it.



have you or anyone had any luck doing this? i have a bullet button i was going to install and epoxy the button hole, but if i dont have to...
11
Legal and Activism / Re: Assualt Pistol Flow Chart
« on: August 15, 2018, 06:35:39 PM »
So as long as i fix my magazine in place, none of the 6 requirements matter? and I could keep it semi auto?
12
General Discussion / Re: Glock 80% Build
« on: August 10, 2018, 07:13:53 PM »
So wondering what is the process of registering a 80% Glock? Has anyone here done this in Honolulu? I wave registered a 80% AR-15 They registered it as custom, and I had a valid Long Gun permit. But the Glock being a pistol there is that 2 week waiting period so where do I get it engraved? And how do I go about doing this since legally I will have the pistol? Any help greatly appreciated.

found this tread in a search, and its the exact question i have.
have you registered your 80% glock yet? if so, did you need your hunters ed?

thanks
Pages: [1]