The term "line" usually refers to the wires carrying useful energy from one place to a separate, other place. As in, "I built a house and brought in the
lines (meaning power lines) last week." Or, "Before you replace that equipment, maybe you'd better check the
line voltage." Meaning the voltage in the building wiring. It is similar to the English usage for domestic power in the wall outlets, which they call "the mains."
Line can have other uses in this context, such as in radio usage, "I used RG-8U cable as a transmission
line from my transmitter to my antenna."
Apart from buying them (capacitors) on-line (allelectronics.com, Grainger, etc), you could pick up used ones from motor rewinding outfits and the like. The author describes the use of electrolytics for AC. Normally electrolytics are DC-polarized, having plus and minus connections, but can be used on AC by connecting two of
equal value in series, but with the two + terminals connected together
or the two minus connections connected together, with the remaining terminals (both of the same polarity --both either -,- or +.+) connected to the outside AC circuit.
This results in a non-polarized electrolytic capacitor of
half the value of the original two capacitors, following the rule of capacitors in series. See the article itself.
I used to pick up high-powered components by salvaging things like old microwave ovens, when I was doing "serious" ham stuff. These contain high-value, high-voltage caps suitable for high-power stuff, as well as other high-power components. Most of the time microwaves crap out and are discarded because something minor happened, like a fuse blowing or the timer circuits fail. So the rest of the stuff is still good.
Yes, capacitors are dangerous. In fact, one thing in the illustration above that I gasped at was the fact that the terminals of the capacitors were exposed. But I assumed that they were covered in normal use, and simply uncovered for illustrative purposes in the photos.
The electrical charges stored by large caps (capacitors) are deadly. The energy stored in a capacitor in Joules is 1/2 X (the voltage squared X the capacitance in Farads). Not the
microFarads.
This is why in high-voltage work, designers always put "bleeder resistors" across them, which discharge the caps slowly when not in use.
Not only are the charges deadly, but electrolytics also have a tendency to recharge themselves when not in use, which is why large ones are shipped with shorting wires across the terminals. The wires drain the self-regeneration charges which can occur over time.
I learned my electronics long before solid-state stuff, where voltages rarely exceed 12 or so Volts, and I was dealing with circuits in various projects which went up past 25,000 volts (TV sets, for example, have at least this kind of anode voltage in them.) The most helpful safety hint when working on this stuff "live" is to lock one hand in the back of your belt, to avoid the temptation to use two hands for an adjustment. In case of a careless move, at least the electrical charge won't go from one hand to the other, through the chest area and your heart.
Hey, you know, it's no worse, really, than dealing with automotive dangers, like, don't do work underneath a car held up by one bumper jack and no chocks. Or, like a friend of mine, who burned down his garage by testing the ignition spark while gasoline fumes were in the engine compartment. No, it wasn't me. I always disconnect the battery when fooling around with anything serious in there. Apparently, car fires due to this cause are fairly common.
So, be careful, of course, but if you don't know what you're doing, get some help and advice. If you google your "location + Amateur Radio Club" you can get in touch with Amateur Radio Operators who are usually delighted to help out in this kind of operation.
As an example, I googled "Honolulu Amateur Radio Club" and brought up their website and contact information for John, K1ER. The acronym "ARC" is common to most
Amateur
Radio
Clubs. Hence, "harc" in the URL.
http://aditl.com/ham/harc/
Hey, John, K1ER, might convert you to amateur radio, and you might convert him into a shooter!

Tee-hee-giggle-giggle!
I sure hope this helps. As I mentioned, this is for the normally-accomplished handyman type. I myself in my old age and dotage don't do large projects anymore (don't have my machine shop any more), but I was thinking of throwing together a small fractional-horse motor rigged as a generator just for shucks and grins.
73s
Terry, 230RN
ETA: I don't know K1ER, never QSLed him. For all I know, he's already a board member.
