Reloading .223? (Read 6909 times)

BLKDRGN

Reloading .223?
« on: July 13, 2014, 06:43:56 PM »
My Dillon 650 came with a .223 setup. I got the Dillion 3-die set. Is the process to resize, trim, deburr, chamfer, and then start reloading? Is it better to buy another resizer die on a separate toolhead just to resize first or should I take out the resizer die and move it to a separate toolhead?
Google it cause every question is a dumb question.

ImKu

Re: Reloading .223?
« Reply #1 on: July 13, 2014, 07:23:01 PM »
IMO, Everyone kind of makes up their own process.   Some do things differently than others.   It is also depends on what equipment you have for brass prep.  For fired brass this the steps I do.
1. Deprime
2. Clean the brass (I don't want crap in my dies)
3. Lube / Resize
4. Trim
5. Deburr / chamfer / primer pocket uniforming
6. Clean the brass (to get the resizing lube off)
7. Load
The mind acts like an enemy for those who do not control it.
- Bhagavad Gita

Hi state

Re: Reloading .223?
« Reply #2 on: July 13, 2014, 08:00:32 PM »
Many .223 and 5.56 cases need to be swaged so don't forget about that step also.

ImKu

Re: Reloading .223?
« Reply #3 on: July 13, 2014, 08:44:01 PM »
And for 5.56 you need to get the crimp out.
The mind acts like an enemy for those who do not control it.
- Bhagavad Gita

BLKDRGN

Re: Reloading .223?
« Reply #4 on: July 13, 2014, 10:41:01 PM »
Never heard of swagging so I read up a little. They say it's for military rounds. Is it safe to say that only 5.56 rounds would need to be swagged? I've only bought commercial .223 and 5.56.
Google it cause every question is a dumb question.

BLKDRGN

Re: Reloading .223?
« Reply #5 on: July 13, 2014, 10:46:28 PM »
IMO, Everyone kind of makes up their own process.   Some do things differently than others.   It is also depends on what equipment you have for brass prep.  For fired brass this the steps I do.
1. Deprime
2. Clean the brass (I don't want crap in my dies)
3. Lube / Resize
4. Trim
5. Deburr / chamfer / primer pocket uniforming
6. Clean the brass (to get the resizing lube off)
7. Load

I have the Dillon 3-die set so it deprimes and resizes at the same time. In my case would it be best to get a separate toolhead with a deprimer only die?
Google it cause every question is a dumb question.

Bcspy

Re: Reloading .223?
« Reply #6 on: July 14, 2014, 12:06:43 AM »
Get a GS custom primer swage for Dillon 650 on eBay. It works good. Way faster than Dillon Swage tool. I like to deprime/size on separate toolhead. Swage, trim, then SS wet tumbler. I like to hand prime all load, so I can inspect again before loading. That's just me.

oldfart

Re: Reloading .223?
« Reply #7 on: July 14, 2014, 04:32:29 AM »
Reference june 6 email.
Tumble
Spend $7, buy a 223 shell holder for the rcbs
Resize on rcbs
Giraud trim
Dump'em in the 650
Pull handle
What, Me Worry?

BLKDRGN

Re: Reloading .223?
« Reply #8 on: July 14, 2014, 07:28:51 AM »
Where does the swagging go in the process? If I go the Dillon 650 route to swage, should I put the deprime and swage dies on the same but separate toolhead?

Deprime
Swage?
Tumble
Lube
Resize
Trim
Deburr/Chamfer
Clean brass
Load
Google it cause every question is a dumb question.

oldfart

Re: Reloading .223?
« Reply #9 on: July 14, 2014, 08:21:00 AM »
deleted

What, Me Worry?

BLKDRGN

Re: Reloading .223?
« Reply #10 on: July 14, 2014, 08:25:40 AM »
OK thanks. I don't have military brass so I should be good.

btw, the swage G.S.Custom powder funnel says it's for XL 550, 650, and 1050. I have no idea where it mounts.
http://www.ebay.com/itm/G-S-Custom-powder-funnel-223-5-56-A-for-the-Dillon-550-650-and-1050-/221483271278?pt=LH_DefaultDomain_0&hash=item33916e846e#ht_675wt_1105
Google it cause every question is a dumb question.

Hi state

Re: Reloading .223?
« Reply #11 on: July 14, 2014, 07:19:44 PM »
Never heard of swagging so I read up a little. They say it's for military rounds. Is it safe to say that only 5.56 rounds would need to be swagged? I've only bought commercial .223 and 5.56.
No I've come a cross .223 that need to be swaged also. Don't know what u mean by "commercial" 5.56 but the 5.56 I've run a cross have had primer crimps that needed to be swaged.
« Last Edit: July 14, 2014, 08:09:08 PM by Hi state »

macsak

Re: Reloading .223?
« Reply #12 on: July 14, 2014, 07:28:31 PM »

BLKDRGN

Re: Reloading .223?
« Reply #13 on: July 14, 2014, 10:03:59 PM »
What kit is the package to the right called? I looks like it's a large primer wheel with small and large pickup tubes. Not sure what the 3rd tube is. Did this come with the Dillon press? I'm thinking of selling it cause I already have the large priming assembly quick-change kit. Actually I'm thinking of selling them all cause I don't need it.

Google it cause every question is a dumb question.

oldfart

Re: Reloading .223?
« Reply #14 on: July 15, 2014, 04:31:34 AM »
If you see a tube that looks like a pickup tube, it might be a primer feed tube. It goes into the steel blast shield.
What, Me Worry?