Adding weight to synthetic stock? (Read 15374 times)

BLKDRGN

Adding weight to synthetic stock?
« on: July 25, 2014, 07:36:55 PM »
We have a Remington 700 SPS .308 Win which has a synthetic plastic stock. I would like to reduce the recoil a little bit more for my wife. It already has a brake and recoil pad. I heard that you can reduce recoil a little by adding weight. What do you think would be a good way on doing this? I read about adding sand, BBs, lead, and molding clay. About how much weight should I add for it to make a difference? I don't mind if it's heavy as it's only for bench rest shooting. Also I would prefer the weight to be removable if possible as we will be getting another stock in the future.

Also no sarcastic comments please. I come here for advice and don't need the crap.  :shaka:



The whole butt stock is hollow which is a lot of space to fill.
Google it cause every question is a dumb question.

suka

Re: Adding weight to synthetic stock?
« Reply #1 on: July 25, 2014, 08:08:03 PM »
adding weights will help reduce recoil a little but not a lot. a heavy gun is much more stables , too.

it's normally used to balance the rifle , such as a seesaw to offset a long barrel. if the stock is toooooo heavy, it won't feel right when shooting.

I've used fishing lead and tire weights at stratigic area. since lead is soft and maluable , it can be shaped to form.

mving4ward

Re: Adding weight to synthetic stock?
« Reply #2 on: July 25, 2014, 08:11:39 PM »
3 rolls of nickel coins, fill the gaps with rags

338KID

Re: Adding weight to synthetic stock?
« Reply #3 on: July 25, 2014, 08:53:17 PM »
What muzzle break do you have on it ?
Fast is fine , accuracy is final

Hi state

Re: Adding weight to synthetic stock?
« Reply #4 on: July 25, 2014, 08:57:20 PM »
You could put some weight on it by adding an aluminum bedded stock and put one of these bump busters on the end off it
http://bumpbuster.blogspot.com/?m=1

BLKDRGN

Re: Adding weight to synthetic stock?
« Reply #5 on: July 25, 2014, 09:09:02 PM »
I think I'll go with the rag and lead since my dad has tons of lead. I have a JP brake which helped a lot but sucker is loud. I don't want to spend too much on it since we are going to get another stock anyways. Thanks guys!
Google it cause every question is a dumb question.

bass monkey

Re: Adding weight to synthetic stock?
« Reply #6 on: July 25, 2014, 10:11:52 PM »
I'd put sand in that open area of the stock. Will add weight and I think would help with recoil too, absorbing it better. Also very adjustable if you want it heavier or lighter to get the right weight.

Since its a synthetic stock do you get any flex issues when shooting? I've heard some savages have that problem so some people stiffen the stock and also use that to add weight to the rifle.

BigBlue

Re: Adding weight to synthetic stock?
« Reply #7 on: July 26, 2014, 12:09:46 AM »
Have you considered working on her form vice modifying the gun?

To really make a noticeable difference you'll add enough weight that you'll throw the balance off which will just lead to worse form/shooting imo (feedback loop).

ghost_medic

Re: Adding weight to synthetic stock?
« Reply #8 on: July 26, 2014, 07:26:43 AM »
 I used bbs from Wal-Mart in a 22lr stock, used a rag to shim it for testing
 then once the weight was correct used spray foam to seal it

if you use foam  the best away is to layer the foam and bbs  so there will be no air pockets

338KID

Re: Adding weight to synthetic stock?
« Reply #9 on: July 26, 2014, 07:39:51 AM »
When going to koko head you should try and take a peice of 2"x4" and a pair of c clamps . Make a stop for the bipod . Tell her to load up on the bipod she should be fine. Her weight should take care of the recoil . I had a no comp installed on my dads 7mm ultra mag and it worked wonders .
Fast is fine , accuracy is final

Surf

Re: Adding weight to synthetic stock?
« Reply #10 on: July 26, 2014, 09:18:39 AM »
Adding weight is great if it is a pure bench rest shooter, but if you have to carry the weapon around for any period of time the added weight sucks and how the weight is added greatly affects the overall balance.  As you noted in your follow up post a new stock gives options when it comes to weight for a bench rifle.  Temporarily others have given good advice.  Simple way is to put a sock in the stock and fill it with sand, shot, lead or BB's.

Other options are learning good technique / body mechanic and as mentioned how to correctly load a bipod if one is used.  Another option for a bench shooter may be a lead sled.   

ren

Re: Adding weight to synthetic stock?
« Reply #11 on: July 26, 2014, 09:39:25 AM »
I've got a 3.5 lb wedge for my AR stock that I took out of my service rifle. It might fill in that stick of yours. When my service rifle weight around 15-17 lbs. I barely moved off the target during rabid fire  ;)
Deeds Not Words

crazy cat

Re: Adding weight to synthetic stock?
« Reply #12 on: July 26, 2014, 10:59:41 AM »
Lead will oxidize and expand, eventually breaking the stock.  That's why it's better to use nickles.

ren

Re: Adding weight to synthetic stock?
« Reply #13 on: July 26, 2014, 12:06:17 PM »
Lead will oxidize and expand, eventually breaking the stock.  That's why it's better to use nickles.

You're dumb.
Deeds Not Words

sa594

Re: Adding weight to synthetic stock?
« Reply #14 on: July 26, 2014, 08:30:01 PM »
Check out tire shops and see if you can pick up lead weights with adhesive backing..just gotta play with the positioning and placement