New P239 (Read 4159 times)

Sodie

New P239
« on: August 07, 2015, 08:05:14 PM »
Took my new (consignment, never fired) P239 in .357 Sig to Koko Head today.

The Good:
The trigger is sweet, and recoil is pretty manageable.  My 17-y.o. daughter handled it well.  Fits my hand nicely...

...The Bad:
Sights appear off in elevation.  Had to hold about 8-10 inches high at 25 yards just to get on target (ammo was American Eagle 125 gr FMJ).  Going to talk to Sig on Monday to see what we might be able to do about that, and also to talk about...

...The Ugly:
No less than FIVE failures-to-feed out of a 50-round box.  Even worse...  When the failures occurred, the bullet hit right on the face of the feed ramp, and they pretty much all "set back" into the case to some degree.  Two of them were really severely pushed back.  Glad I saw it, and didn't try to shoot them again...   :shake:  Email sent to Federal to let them know about that problem.  Pic of the worst two setbacks attached.

horse808

Re: New P239
« Reply #1 on: August 07, 2015, 10:40:42 PM »
Congrats on your new Sig.  We have the same sight elevation problem with my wife's P239 even using a combat sight picture instead of a 6 o'clock hold.  The 9mm's have Siglite #8s front and back and other forums have recommended changing the rear to a taller #10 to raise POI.  Not sure what sights the .357s come with from the factory though.

Sodie

Re: New P239
« Reply #2 on: August 08, 2015, 07:57:10 PM »
Thanks for the words, Horse.  I did a little research into Sig sights, and apparently they use a "combat" sight picture (front sight covering the bullseye) at 15 yards for zero.  I was at 25 yards with a 6 o'clock hold (lots of muscle memory there), so that would account for some of it.  Wish I had access to a benchrest and a 15 yard range so I could see the actual zero for myself.  Or I could just buy new sights...

horse808

Re: New P239
« Reply #3 on: August 09, 2015, 01:01:49 AM »
We also tried using heavier ammo (147gr American Eagle) which seemed to shoot on a flatter trajectory but the only thing we hit consistently was the big square plate on the metallic range.  If you're willing to give up the night sight, LPA makes an adjustable rear sight for Sigs but you'll also need to invest in a sight pusher to do the swap.  Sig also has a service package on their website which includes replacing the nights sights for a reasonable cost but the shipping is a little pricey and humbug.

horse808

Re: New P239
« Reply #4 on: August 09, 2015, 01:04:51 AM »
Someone else might know this but can you sight in at 15 yards at one of the indoor ranges? 

mauidog

Re: New P239
« Reply #5 on: August 09, 2015, 11:09:32 AM »
Sig warrants their products.  If the sights are that far off, they should correct it.  Of course, you pay in shipping and waiting, but they should be able to correct the issues.

They will charge you a service fee up front.  If the problem is determined to be covered under warranty, they will refund the fee.  If not, your fee covers their diagnostic service.

I've read they actually replaced entire slides for customers who complained the pistol was not shooting anywhere close to where they aimed.

Hope that's helpful.
An unarmed man can only flee from evil, and evil is not overcome by fleeing from it.   -- Jeff Cooper

macsak

Re: New P239
« Reply #6 on: August 09, 2015, 11:59:57 AM »
Someone else might know this but can you sight in at 15 yards at one of the indoor ranges?

at hnl firearms, you can shoot from 0-17 yards
when xring eventually opens, it will be a 25 yard range

Sodie

Re: New P239
« Reply #7 on: August 09, 2015, 06:03:07 PM »
Thanks, Dog.  Since I'm technically the second owner, I don't think I'd qualify for warranty coverage. Sig's website says the warranty isn't transferable.  Before I go back to Sig with it, I'll want to make sure my duck are in a sock, so to speak. That why I'd like to give it a try at 15 yards from some sort of rest with a proper sight picture and see if its really that far off. At 25 yards, the difference between a 6 o'clock hold and a "combat" hold would account for at least a few inches.