Fiber Optic Front Sights - Please Share Your Experiences (Read 45645 times)

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #40 on: February 10, 2016, 12:49:56 PM »
Thanks Surf for posting that video!   :thumbsup:

On two Gen 4 Glock 17s (what I would consider my primary defensive and training guns), I have 10-8 RB1 version sights, Tango Down/Vickers slide and mag release and grip plug (don't recall what brand).  With the grip plug, it does have a ramp section that helps with reloads, but I recall that I had to shape the ramp section some because it was actually preventing the mag from dropping free.

I've considered playing around with the texturing the grip, but I haven't yet.  Mostly because I'm too chicken to start down that path of dremeling and soldering iron.  A bunch of shooting buddies do it to their Glocks, so I can always have them guide and assist, but I just haven't gotten over that hump.  The finger grooves fit me pretty well, or at least I don't notice them in a negative way.  One mod that I should eventually look into is the undercutting of the trigger guard.  I do have the "Glock knuckle" and it occasionally does end up hurting, but seems like only in multiday classes which I haven't done in a while. 

The two mods that really interest me are the memory notch on the bottom of the trigger guard and the narrowing of the depth of the grip.  I have to break my grip some to release the mag and do a slight rotate of the grip to access the release.  I sort of just lived with it.  An instructor in the past did notice and point out to me that I seemed to be throwing my first shot after reload.  After concentrating on reestablishing my grip after the reload, I was able to tighten that up, but I think it would help if I didn't have to break my grip to drop the mag.  On the new PPQ, I can release the mag without affecting my grip much.  The memory notch is also a new concept to me, but I think that would help, especially when my hands sweat (which happens often when shooting in Hawaii) and my left hand is clamping down on a sweaty outer part of my right hand fingers.

The other mod that I've tired recently is the Ghost Edge connector, but that was more out of curiosity.  I have that in my 34 for now and will have to give it more time to see if it grows on me.  My first impressions were a solid meh.  Haha.  In the past, I stuck pretty close to stock Glock configuration where the sights were about the only thing I would change.  In the past 2 years or so, I've expanded on what I will change.

Drakiir84

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #41 on: February 11, 2016, 02:55:22 PM »
Thanks Surf for posting that video!   :thumbsup:



I've considered playing around with the texturing the grip, but I haven't yet.  Mostly because I'm too chicken to start down that path of dremeling and soldering iron.  A bunch of shooting buddies do it to their Glocks, so I can always have them guide and assist, but I just haven't gotten over that hump.  The finger grooves fit me pretty well, or at least I don't notice them in a negative way.  One mod that I should eventually look into is the undercutting of the trigger guard.  I do have the "Glock knuckle" and it occasionally does end up hurting, but seems like only in multiday classes which I haven't done in a while. 

I've got 2 extra rubber grips if you want to try it.  Already have it on my Gen 4 so you can see if you like it.
"The rifle is a weapon. Let there be no mistake about that. It is a tool of power, and thus dependent completely upon the moral stature of its user. It is equally useful in securing meat for the table, destroying group enemies on the battlefield, and resisting tyranny. In fact, it is the only means of resisting tyranny, since a citizenry armed with rifles simply cannot be tyrannized."
-Jeff Cooper

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #42 on: February 18, 2016, 02:50:16 PM »
I've got 2 extra rubber grips if you want to try it.  Already have it on my Gen 4 so you can see if you like it.
Thanks, but I'm good.   :thumbsup:

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #43 on: February 18, 2016, 02:55:45 PM »
After a couple of range sessions with the 34, I'm liking them.  Will have to wait until I get the gun through a competition or two and see how that goes.  Until then, I just ordered a set of 10-8 sights for my PPQ M2 that has the plain/serrated rear sight and fiber optic front sight.  There was an option for a tritium dot on the front sight, which would make the sight set very similar to the setup that I have on two of my Glock 17s.  However, for now, I'd like to try the fiber front sight for now, but good to know that I have the option to swap the front sight to a setup that I am already familiar with. 

I looked into the HIVIZ front sight and it was about the same price as the 10-8 front sight.  I went back and forth on which to choose, but for now, I went with the 10-8 set and can look into the HIVIZ in the future.  Another thing about going away from tritium is that the sights seem to be priced quite a bit lower. 

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #44 on: February 22, 2016, 07:39:54 AM »
Shot my first match with the new sights this past weekend and they are awesome!  It was a sunny day and that fiber is super bright!  Very easy to pick up and the smaller filament/rod was an improvement over the orange circle around the tritium dot on my old sight.  Seemed like I had an easier time on the smaller steel plates. 

One thing that a friend pointed out to me is that not all fiber front sights have all or most of the filament/rod exposed like mine does.  It's still bright, but with more of the body of the rod exposed makes it really bright!  Probably a tradeoff between durability and brightness.  Something I'll have consider if I were to put these on a defensive gun.  The 10-8 sights that I have on order for my PPQ seem to have more support on the rod, so will have to see how that works. 

I'll definitely be sticking with these Dawsons for my 34.  Will see if I will be changing out sights on other guns to fiber fronts.  My RIA 1911 is one potential. 

oldfart

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #45 on: February 22, 2016, 11:01:20 AM »
Shot my first match with the new sights this past weekend and they are awesome!  It was a sunny day and that fiber is super bright!  Very easy to pick up and the smaller filament/rod was an improvement over the orange circle around the tritium dot on my old sight.  Seemed like I had an easier time on the smaller steel plates. 

One thing that a friend pointed out to me is that not all fiber front sights have all or most of the filament/rod exposed like mine does.  It's still bright, but with more of the body of the rod exposed makes it really bright!  Probably a tradeoff between durability and brightness.  Something I'll have consider if I were to put these on a defensive gun.  The 10-8 sights that I have on order for my PPQ seem to have more support on the rod, so will have to see how that works. 

I'll definitely be sticking with these Dawsons for my 34.  Will see if I will be changing out sights on other guns to fiber fronts.  My RIA 1911 is one potential.
...
Was that at mppl on Saturday?
What, Me Worry?

Surf

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #46 on: February 22, 2016, 09:44:00 PM »
drck1000 - A couple quickies.  Ditch the Ghost connector it gives a horrible mush feel, pick up a Zev connector.  Don't sweat the durability of fiber tubes on a for fun gun they are easy to change.  I am hard on my pistols and break tubes, but I am probably just a bit lazy and want to know that the tube is there when I pull out the pistol, so I go with a Highviz overmolded because of the durability but I own TruGlo, Dawson and Novak also. 

Be aware that you don't force a sight onto the pistol.  I still fit sights the old fashioned way, with a set of files, punch, hammer and vise.  You can force on a tough to fit sight and for a sight that isn't going off and another replacing isn't going to be a problem, but some people force on a sight and screw up the dovetail on the slide over sizing it.  Also with a sight pusher, once you get strong tension, two twists to tight, then back it off and repeat.  Don't continually crank in one continuous tension.  Of course these things will not always cause issues, but otoh they can very easily screw something up.

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #47 on: February 23, 2016, 08:35:23 AM »
drck1000 - A couple quickies.  Ditch the Ghost connector it gives a horrible mush feel, pick up a Zev connector.  Don't sweat the durability of fiber tubes on a for fun gun they are easy to change.  I am hard on my pistols and break tubes, but I am probably just a bit lazy and want to know that the tube is there when I pull out the pistol, so I go with a Highviz overmolded because of the durability but I own TruGlo, Dawson and Novak also. 

Be aware that you don't force a sight onto the pistol.  I still fit sights the old fashioned way, with a set of files, punch, hammer and vise.  You can force on a tough to fit sight and for a sight that isn't going off and another replacing isn't going to be a problem, but some people force on a sight and screw up the dovetail on the slide over sizing it.  Also with a sight pusher, once you get strong tension, two twists to tight, then back it off and repeat.  Don't continually crank in one continuous tension.  Of course these things will not always cause issues, but otoh they can very easily screw something up.
Thank you (as always) for the feedback!  :thumbsup:

About the Ghost connector, I am still meh about it.  Actually forgot about it when I was shooting the match this past weekend.  From the range time I had, it lacks the distinct wall that the stock trigger had, which I have grown to be accustomed to.  I sort of wrote it off that you'd have to replace the entire trigger assembly (Vogel, Haley, Guardian, etc) and don't want to spend that kind of money right now.  Up until this point, I haven't changed out anything internal and the Ghost connector was something I tried out on a whim when I saw it at SEC.  That said, I will give the ZEV connector a try.  Who knows, maybe one day I'll venture into replacing the trigger assembly, but probably not any time soon.  And if I do, it will be on my 34 and likely leave my 17s alone. 

Yeah, not really worried about the durability of the fiber optic front sight on my 34 since it is pretty much only for competition.  Now that I said that, I should probably keep the replacement filament and a lighter in my range bag.  Haha.  For my 17s, the hardest use they've seen are multiday classes in the snowy and freezing Alaska and the current sights have made it through those with no problems.  It would be interesting to see how the fiber sights would've held up.  Didn't really notice if other shooters had those.  I should ask.  It might be a while before I consider switching the sights on the 17s, but I'm definitely liking the Dawsons on my 34.  Even then, my 17s are far from work guns, but I'd also like the confidence, preferably through personal experience, that they can take a beating.  Until then, I'll have to rely on product reviews, which includes your feedback. 

I just watched the video that Dave Dawson posted on installing his rear sights.  And doh. . .  While I didn't crack the rear slide nor beat up the rear sight installing it, I bet I altered the shape of the channel for the rear sight.  Dave Dawson mentioned that Glock cuts the rear channel [wide end-taper to slightly narrower in the middle-wide end] to secure the stock polymer sights.  That's about what I noticed with max resistance as the sight reached the middle and then somewhat constant after that.  When I horsed the Dawson rear sight on, I probably altered the channel slightly in that middle area.  Live and learn.  Good thing is that I am happy with the Dawson set up for now.  Maybe a good reason to buy another 34 in the future.   :P 

Good timing too for this discussion as the 10-8 sights for my PPQ came in last night.  From reviews on the 10-8 sights, I expected to have to do some filing and have a #2 swiss file for when I had to do some minor filing on a previous set of 10-8 front sights.  Interesting that the reviews for 10-8 rear sights for M&P and PPQ all mention needing filing, but the 10-8 rear sight for my Glock 17s didn't need any filing and didn't need to horse them on like I did for 34.  As mentioned before, up until recently, I haven't ventured to far into modifications on any of my guns.  I really should invest in a decent, but somewhat portable, vice for working on my guns and do it right.  Wish I had a house where I could have a nice workshop like in Dave Dawson's videos! 

oldfart

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #48 on: February 23, 2016, 09:15:37 AM »
I'm not a glockhead, but my son installed truglo tg h3 sights on my g17. I like the bright glow. Easier for old eyes to see.
Re. Zev....I dropped the 25 buck kit in and I really enjoy the gun now.
Shot a steel match with it last year and did ok, all things considered.
What, Me Worry?

Surf

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #49 on: February 23, 2016, 08:06:41 PM »
Thank you (as always) for the feedback!  :thumbsup:

About the Ghost connector, I am still meh about it.  Actually forgot about it when I was shooting the match this past weekend.  From the range time I had, it lacks the distinct wall that the stock trigger had, which I have grown to be accustomed to.  I sort of wrote it off that you'd have to replace the entire trigger assembly (Vogel, Haley, Guardian, etc) and don't want to spend that kind of money right now.  Up until this point, I haven't changed out anything internal and the Ghost connector was something I tried out on a whim when I saw it at SEC.  That said, I will give the ZEV connector a try.  Who knows, maybe one day I'll venture into replacing the trigger assembly, but probably not any time soon.  And if I do, it will be on my 34 and likely leave my 17s alone. 

Yeah, not really worried about the durability of the fiber optic front sight on my 34 since it is pretty much only for competition.  Now that I said that, I should probably keep the replacement filament and a lighter in my range bag.  Haha.  For my 17s, the hardest use they've seen are multiday classes in the snowy and freezing Alaska and the current sights have made it through those with no problems.  It would be interesting to see how the fiber sights would've held up.  Didn't really notice if other shooters had those.  I should ask.  It might be a while before I consider switching the sights on the 17s, but I'm definitely liking the Dawsons on my 34.  Even then, my 17s are far from work guns, but I'd also like the confidence, preferably through personal experience, that they can take a beating.  Until then, I'll have to rely on product reviews, which includes your feedback. 

I just watched the video that Dave Dawson posted on installing his rear sights.  And doh. . .  While I didn't crack the rear slide nor beat up the rear sight installing it, I bet I altered the shape of the channel for the rear sight.  Dave Dawson mentioned that Glock cuts the rear channel [wide end-taper to slightly narrower in the middle-wide end] to secure the stock polymer sights.  That's about what I noticed with max resistance as the sight reached the middle and then somewhat constant after that.  When I horsed the Dawson rear sight on, I probably altered the channel slightly in that middle area.  Live and learn.  Good thing is that I am happy with the Dawson set up for now.  Maybe a good reason to buy another 34 in the future.   :P 

Good timing too for this discussion as the 10-8 sights for my PPQ came in last night.  From reviews on the 10-8 sights, I expected to have to do some filing and have a #2 swiss file for when I had to do some minor filing on a previous set of 10-8 front sights.  Interesting that the reviews for 10-8 rear sights for M&P and PPQ all mention needing filing, but the 10-8 rear sight for my Glock 17s didn't need any filing and didn't need to horse them on like I did for 34.  As mentioned before, up until recently, I haven't ventured to far into modifications on any of my guns.  I really should invest in a decent, but somewhat portable, vice for working on my guns and do it right.  Wish I had a house where I could have a nice workshop like in Dave Dawson's videos!
The Ghost has a terrible mush to it.  The Glock slide is pretty stout so you may not have opened it up, but I have seen it done several times, but most people don't swap sights often.  Dawson and many other custom fit guys purposely make their sights oversized to get a good custom fit.  These are generally the shooter / gunsmith types that produce products.  A lot of the more standard stuff, is well more standard dovetail sized.  Just remember to take the file to the sight and not the dovetail.  Yep, seen that happen. 

As far as the drop in trigger kits out there, they are simply doing what many of us have been doing for years with custom work.  Some just got smart and marketed the kits.  I will tell you 110% that you don't need to pay for a drop in kit.  If I let you shoot my pistol next to a Haley, Vogel, etc, you will be extremely disappointed in your purchase.  I almost don't like to let people shoot my pistols if they have a drop in kit in their pistol.  What I do isn't exactly rocket science and is easily repeatable for a fraction of the cost of the kits.  Of the majority of armoring or gunsmithing that I do, the Glock stuff really is very simple stuff.  Now if someone wanted a full race trigger, I can do some pretty scary stuff in the 1.5# - 2# range.  I don't even like those triggers.

If you are ever at the range on a weekday, I would be more than happy to let you check out my set ups and give them a try.  I don't go to the range on weekends however.

I'm not a glockhead, but my son installed truglo tg h3 sights on my g17. I like the bright glow. Easier for old eyes to see.
Re. Zev....I dropped the 25 buck kit in and I really enjoy the gun now.
Shot a steel match with it last year and did ok, all things considered.
I agree.  As my eyes get older the fibers really help.  I ran the TruGlo's for a few years.  I am also a fan of the Zev kit.  I talk about it a bit in the Part 2 of my Glock Mods video.
« Last Edit: February 23, 2016, 10:22:34 PM by Surf »

Surf

Coconut-kid

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #51 on: February 23, 2016, 09:05:15 PM »
I'm late to the party but I like to run FO on most of my pistols.  I just installed a set of Dawson Percisions on my VP9. I like to run green up front. I seem to pick it up faster than the red. 

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #52 on: February 24, 2016, 07:40:16 AM »
The Ghost has a terrible mush to it.  The Glock slide is pretty stout so you may not have opened it up, but I have seen it done several times, but most people don't swap sights often.  Dawson and many other custom fit guys purposely make their sights oversized to get a good custom fit.  These are generally the shooter / gunsmith types that produce products.  A lot of the more standard stuff, is well more standard dovetail sized.  Just remember to take the file to the sight and not the dovetail.  Yep, seen that happen. 

As far as the drop in trigger kits out there, they are simply doing what many of us have been doing for years with custom work.  Some just got smart and marketed the kits.  I will tell you 110% that you don't need to pay for a drop in kit.  If I let you shoot my pistol next to a Haley, Vogel, etc, you will be extremely disappointed in your purchase.  I almost don't like to let people shoot my pistols if they have a drop in kit in their pistol.  What I do isn't exactly rocket science and is easily repeatable for a fraction of the cost of the kits.  Of the majority of armoring or gunsmithing that I do, the Glock stuff really is very simple stuff.  Now if someone wanted a full race trigger, I can do some pretty scary stuff in the 1.5# - 2# range.  I don't even like those triggers.

If you are ever at the range on a weekday, I would be more than happy to let you check out my set ups and give them a try.  I don't go to the range on weekends however.

I agree.  As my eyes get older the fibers really help.  I ran the TruGlo's for a few years.  I am also a fan of the Zev kit.  I talk about it a bit in the Part 2 of my Glock Mods video.
I recall one of the packages available online (I think glocktriggers.com or something like that) did mention something about it being made up of all OEM parts that they polished, ground, etc.  So pretty much what you said about them just marketing and packaging what people did as "home trigger jobs".  As one to hasn't really tinkered much with my guns, I am also a bit cautious of messing things up through experimenting.  I've seen so much stuff like competition guns starting to double when the owner messed with something.  That said, l've lately been venturing more into the tinkering realm. . . If I had dedicated workshop and a range where I could to side-by-side or before/after testing, I could see that taking up a LOT of my time, and money.  I had a backyard range like Hickok45, I'd be broke.  ;D

I'll have to take you up on that offer one of these days! 

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #53 on: February 24, 2016, 07:44:07 AM »
I'm late to the party but I like to run FO on most of my pistols.  I just installed a set of Dawson Percisions on my VP9. I like to run green up front. I seem to pick it up faster than the red.

My Dawsons came with red installed and replacement red and green.  The 10-8 set came with red and green filaments, but none installed.  I'll probably stick with red for now. 

I thought I read somewhere that the human eye generally picks up green easier or faster than red.  Eventually, I'll likely experiment with green. 

jaynick

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #54 on: February 24, 2016, 08:57:47 AM »
My Dawsons came with red installed and replacement red and green.  The 10-8 set came with red and green filaments, but none installed.  I'll probably stick with red for now. 

I thought I read somewhere that the human eye generally picks up green easier or faster than red.  Eventually, I'll likely experiment with green.
i also want to try switching my red front/green rear to the opposite, but i was saving that til they broke with use. its been 3 years and theyre still solid. i even use 91% alcohol sometimes to wipe off light dust and sweat from the range. i thought for sure the fiber optic would be dull and useless by this point.

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #55 on: February 24, 2016, 01:18:07 PM »
Glock Mods Part II

https://www.youtube.com/watch?v=qLTs0gIaSt4&feature=youtu.be
:thumbsup:

I never really had an interest in changing anything internal to any of my Glocks until I got and started shooting the PPQ.  My two 17s and 34 came with the current/proven RSA and ejectors.  I've had good luck so far in function of all of them and no problems that have been reported from some Gen 4 9 mm, like brass to the face.  As I mentioned previously, the Ghost connector was sort of a whim.  I have since ordered the ZEV and I think it should be here end of the week.  Easy drop in part to change. 

My buddy's 19 had some extraction problems and he subsequently swapped out the ejector and RSA.  I believe his gun had the 336 ejector, but not sure which RSA.  After he swapped those out, so far the function is at 100%. 

A bunch of shooter friends have all sorts of mods to their guns, particularly Glocks.  I have resisted going beyond stuff like sights, mag release and slide catch/release, but slowing getting more of an interest in tinkering.  I'm thinking of getting a 19 soon that will be a project and experiment gun.  One of the first mods that I will try will likely be stippling.   

What are your thoughts/preferences toward expected service life for the internal parts?  Particularly the RSA.  I've read anywhere from as soon as 5000 rounds to up to 10k.  Two of my Glocks are pretty close to 5000 each.  Now that I think about it, that's a lot that I spent in ammo.  Haha. 

Match barrels are another popular drop in change that I see quite often.  I've always wondered how much difference in accuracy that they could offer.  However, I guessed that without fitting to the particular slide and frame, that there would be a limit to how much improvement one could see and that seems to mirror your experience.  I also wondered if you got a match barrel fitted so tightly as to improve accuracy that one walks the fine line of too little tolerance for reliable function.  That and I don't see the slide to frame fit on a Glock able to tighten that up very much.  I wouldn't mind trying say a Wilson Combat match barrel for my 34 and shoot in competition though, just out of curiosity.   ;D

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #56 on: February 24, 2016, 01:22:25 PM »
i also want to try switching my red front/green rear to the opposite, but i was saving that til they broke with use. its been 3 years and theyre still solid. i even use 91% alcohol sometimes to wipe off light dust and sweat from the range. i thought for sure the fiber optic would be dull and useless by this point.
Interesting.  Any reason you're thinking of reversing red front/green rear to green front/red rear?  Do you think you'll pick that up better?  Or just to experiment?

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #57 on: February 29, 2016, 11:22:19 AM »
Installed the 10-8 sights on my PPQ over the weekend and it was a little bit of a PITA.  I read that the 10-8 sights have a surface coating/treatment that is very tough.  I have a #2 swiss cut file that I bought specifically for working on a 10-8 front sight for my Glock 17s.  That was the file that Hilton specifically recommended.  Anyways, that file wasn't doing anything!  I had to bust out a diamond knife sharpener to break through the surface coating/finish.  Once I broke through the black surface finish, it was easier, but they must use a steel that is hardened to a high level of toughness. 

Eventually got it filed and fitted.  The 10-8 front sight comes with a red and green fiber rod and you have to install yourself.  That is in contrast to the Dawson set that came with red and green fiber rods with a red already installed.  Not a big deal, but the Dawson set coming with the red installed did help.  I messed up the first two attempts to install the red fiber rod.  I probably have enough for one replacement, but I used up over half of the rod.  It's not difficult, but it's helpful to have gone through it once as the fiber rod melts quickly and mushrooms quicker than I thought. 

Shot the PPQ at the bullseye range to set the drift of the rear sight and got to shoot it in the sunlight over the weekend. I'm quickly becoming a big fan of the fiber optic front.  A friend who is relatively new to shooting was also at the range and he was saying how his eye sight makes it tough to pick up the front sight of his 19.  I had him try my PPQ with the fiber optic red front sight and another friend's 19 with the Trijicon HD orange front sight.  He shot both better, but he did say that he picked up the red FO sight best. 

I'll definitely be shooting both my 34 and PPQ a lot in the coming months.  That will give me a better idea of durability of the sights over time as well.  I have tentative plans for a pistol course later this spring, but nothing firm yet.  I am looking forwarding to seeing how these sights perform over the next many months, but I like them a lot so far. 

I'm also really liking the PPQ as well.  I enjoy trying a variety of handguns, but my Glock 17s have been my primary defensive and training handguns.  That's not likely to change any time soon, but I can see the PPQ challenging for spot. 

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #58 on: May 23, 2016, 08:05:14 AM »
Have shot a handful of matches with my Glock 34 and Dawson Precision FO sights and I'm definitely liking them.  They are very bright and easy to pick up.  Haven't really shot on overcast days, but in the shade of the bulls eye range, the front sight is still easy to pick up.   

The FO on my PPQ is from 10-8 and is also larger diameter.  I haven't shot the PPQ in a match yet, but when the 5" version arrives, it will definitely get some time in matches.  While I am waiting for it to arrive, I am debating between the smaller and larger diameter front sight. I'm leaning toward the Dawson Precision ones with the charger rear and a larger diameter front sight.  I may also look into trying the HIVIZ front sights as well. Either on the PPQ or a Glock 19. 

drck1000

Re: Fiber Optic Front Sights - Please Share Your Experiences
« Reply #59 on: May 22, 2017, 03:25:52 PM »
If anyone is interested in Hiviz sights, they are on sale at Optics Planet right now.  Most are in the 40-50% range.  The shipping is pricey, but still comes out cheaper than any place else that I've found. 

Seems like most have decent number in stock, while some are running low.  I ordered an overmolded red (0.12") and a standard fiber rod model that comes with red, green and white rods (0.08") to test out in my 17s.  From the dimensions, it seems like they will work fine with the 10-8 rear sights that I currently have on there. 

Finally shot the PPQ 5" with Dawson sights this past weekend.  Same sights I have on my 34 with a slightly different rear sight.  I hope to get that gun in an IPSC/USPSA match after the Aloha State games.  Seems like for the PPQ, Dawson and 10-8 are the only one producing sights for those models.  Or at least that offer FO front and plain/serrated rear sights. 

Now I'm thinking about trying out a FO for my RIA 1911 too.  This is getting expensive.   :(