.223/5.56 MIL Re-loads / Chrono (Read 42952 times)

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #20 on: January 12, 2017, 06:15:08 PM »
It isn't 27.4, it's loaded to 27.2gr with it throwing on the lower end closer to 27.0 gr. The CFE 223 is a little sticky and it likes to cling to the walls of everything like static.. I could also barely see through the side of my Lee press to see powder height and I'm guessing at 26.0gr I probably wouldn't be able to see down the neck at my angle.

Do you happen to know the name of the manual you're referencing? I'd like to get a copy since my Lee Modern reloading book doesent list CFE 223. Like mentioned, I could only get the VMD factor online and compare it to something similar (BCL-2).

Thank you for your input.   :thumbsup:

I was at work and only had my Nosler and Hodgdon on hand.

For static, try wiping the hopper down with a dryer sheet.


Sent from my iPhone using Tapatalk

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #21 on: January 12, 2017, 06:19:03 PM »
Just in case u didn't know, you can access Hodgdon's load data online for free. They list all their powders with various bullets. They also come out with a revised magazine with data every year.


Sent from my iPhone using Tapatalk

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #22 on: January 12, 2017, 08:02:31 PM »
Just in case u didn't know, you can access Hodgdon's load data online for free. They list all their powders with various bullets. They also come out with a revised magazine with data every year.


Sent from my iPhone using Tapatalk

I've mentioned using their website in a earlier response for load data. Selecting the mentioned cartridge, caliber, powder and bullet grain combo;  hodgedonreloading doesent have the 'exact' load data for this setup.

Did you happen to have the name of the two manuals that you were referring to that had CFE 223 load data in it? or were you referring to online?

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #23 on: January 12, 2017, 08:11:02 PM »

Did you happen to have the name of the two manuals that you were referring to that had CFE 223 load data in it? or were you referring to online?

Both were hard copies. Nosler and Hodgdons. If you need, I can take pics of the Nosler. The Hodgdons is the same online.


Sent from my iPhone using Tapatalk

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #24 on: January 12, 2017, 08:49:01 PM »
Both were hard copies. Nosler and Hodgdons. If you need, I can take pics of the Nosler. The Hodgdons is the same online.


Sent from my iPhone using Tapatalk

Post it up, I'd like to see what you're referring to.

Thanks.

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #25 on: January 13, 2017, 07:19:18 AM »
Post it up, I'd like to see what you're referring to.

Thanks.
Probably not a good idea to post pages out of reloading manuals. I am a member of a few reloading forums and they don't allow this practice due to copyright issues that they had in the past with the owners of the material. But I am sure no one will know if one e-mails it to you. JMHO  :shaka: :shaka: :shaka:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

oldfart

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #26 on: January 13, 2017, 08:14:54 AM »
Pro But I am sure no one will know if one e-mails it to you. JMHO  :shaka: :shaka: :shaka:
==========
unless you are on 3 FBI watch lists :rofl:
What, Me Worry?

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #27 on: January 13, 2017, 08:23:00 AM »
Probably not a good idea to post pages out of reloading manuals. I am a member of a few reloading forums and they don't allow this practice due to copyright issues that they had in the past with the owners of the material. But I am sure no one will know if one e-mails it to you. JMHO  :shaka: :shaka: :shaka:

That's something interesting to know. You figure it's public information, can be obtained from buying a book and viewed on a website.  ???

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #28 on: January 13, 2017, 08:48:45 AM »
I think the Hornady manual is really good.
https://www.midwayusa.com/product/235643/hornady-handbook-of-cartridge-reloading-10th-edition-reloading-manual

I have the Lyman 49th edition but doesn't have CFE223 in it. I copied the following from the website that indicates 24.7 to 27.4. The rifle and ammo is obviously not the same which is why it's best to start low. There's a YouTube video where Johnny started his ARcomp load at 22.3 gn. and blew out his primers so you never know. I tried CFE223 last week from 20 to 24 gn. I thought the 24 gn was really, really hot. Unfortunately, the bullets I was using were crap so it was difficult to choose a prime load. What I didn't like with CFE223 was that it discolored the brass afterwards. It will probably tumbler out but don't have one yet. So far, my rifle seems to like AR comp the best.

55 GR. BAR TSX FB
Starting Loads Maximum Loads
Manufacturer   Powder   Bullet Diam.   C.O.L.   Grs.   Vel. (ft/s)          Pressure        Grs.      Vel. (ft/s)       Pressure
Hodgdon           CFE 223   .224"           2.180"      24.7   3,065   44,600 PSI   27.4       3,317             54,000 PSI

https://youtu.be/h1KJpDyzq0c?list=PLTTrjvDib94mGnOlwzzwOPCreXUiGp1dH
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #29 on: January 13, 2017, 09:27:51 AM »
I think the Hornady manual is really good.
https://www.midwayusa.com/product/235643/hornady-handbook-of-cartridge-reloading-10th-edition-reloading-manual

I have the Lyman 49th edition but doesn't have CFE223 in it. I copied the following from the website that indicates 24.7 to 27.4. The rifle and ammo is obviously not the same which is why it's best to start low. There's a YouTube video where Johnny started his ARcomp load at 22.3 gn. and blew out his primers so you never know. I tried CFE223 last week from 20 to 24 gn. I thought the 24 gn was really, really hot. Unfortunately, the bullets I was using were crap so it was difficult to choose a prime load. What I didn't like with CFE223 was that it discolored the brass afterwards. It will probably tumbler out but don't have one yet. So far, my rifle seems to like AR comp the best.

55 GR. BAR TSX FB
Starting Loads Maximum Loads
Manufacturer   Powder   Bullet Diam.   C.O.L.   Grs.   Vel. (ft/s)          Pressure        Grs.      Vel. (ft/s)       Pressure
Hodgdon           CFE 223   .224"           2.180"      24.7   3,065   44,600 PSI   27.4       3,317             54,000 PSI

https://youtu.be/h1KJpDyzq0c?list=PLTTrjvDib94mGnOlwzzwOPCreXUiGp1dH

I didn't go with that load data from hodgdonreloading.com. The Barnes Tripple Shock FB bullet is much longer than the xtremebullet 55g .223 FMJ that I used. The OAL is also shorter than the OAL that I used meaning the bullet gets seated farther in. I went off my Lee book.

Since the bullet is longer & the load data is for 2.180" (seated farther in the cartridge), it creates less space inside of the .223 cartridge raising the pressure.

I haven't used this powder yet but I'm not too concerned with it making my brass dirty. You should see the brass I'm starting with. It's semi corroded and heavily tarnished. Nothing a few hours in stainless media can't fix.

Heavies

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #30 on: January 13, 2017, 09:55:04 AM »
Easiest is......    http://www.hodgdonreloading.com/

Since their powders are seemingly the most prolific on the island of Oahu, it is probably the best source for up to date data.  I doesn't give you specifics for the reloading process like a good reloading book will, but it does have great data for a good starting point.

I like to do a lot of research, cross referenced with this published data, to give me an idea of what load to start with, and where a range of charge to concentrate on for best accuracy.  That way I'm not starting at the very bottom and working all the way to the top. 

Also, a careful and methodical inspection of cases for signs of pressure is done, when starting off with new loads and new powders, for safety.

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #31 on: January 13, 2017, 10:05:00 AM »
Easiest is......    http://www.hodgdonreloading.com/

Since their powders are seemingly the most prolific on the island of Oahu, it is probably the best source for up to date data.  I doesn't give you specifics for the reloading process like a good reloading book will, but it does have great data for a good starting point.

I like to do a lot of research, cross referenced with this published data, to give me an idea of what load to start with, and where a range of charge to concentrate on for best accuracy.  That way I'm not starting at the very bottom and working all the way to the top. 

Also, a careful and methodical inspection of cases for signs of pressure is done, when starting off with new loads and new powders, for safety.

Ragah! Noted.

I'll probably batch the next few hundred to 25-25.5gr, depending on what auto disc drops I have on hand for the next lot.

Thanks for the input.  :thumbsup:

Heavies

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #32 on: January 13, 2017, 10:48:55 AM »
Skipping steps in working a load can cause problems.  I learned the hard way here.  I changed only one variable....  Same bullet weight just a different brand and profile..



I had purchased some brand new cases, and all I wanted to do is fireform them to my chamber.  I didn't want to use expensive target bullets to do this, so I figured I blast some cheap bullets instead.  All the rounds went though the same hole on target at 100yards...  (testament to OCW theory of load development!)    I got through the whole box of 50 that I made before I realized something was wrong when the last few cases wasn't being ejected from the action.  All the rounds went though the same hole on target at 100yards...  (testament to OCW theory of load development!)

If you look at the top cases you can see the blow by and excessively flat the primer. 

problem 1.  I didn't work up the load with the new component
problem 2.  I didn't inspect any of the cases per shot, I didn't think it would make any difference.

Lucky for me, and my face, the only thing that happened is I ruined about half my new cases, damaged the ejector spring, and slightly etched my bolt face.  This is in a high end target action, imagine if this was a semi auto,  Might have blown it up.

Now my very expensive target rifle has and ugly bolt face, and wasted money on new Winchester cases.  could have been much worse.

oldfart

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #33 on: January 13, 2017, 10:54:13 AM »
Ragah! Noted.

I'll probably batch the next few hundred to 25-25.5gr, depending on what auto disc drops I have on hand for the next lot.

Thanks for the input.  :thumbsup:
...
Suggestion....
You spend plenty on the guns and reloading stuff.
Maybe better replace the Lee powder measure with something with less plastic,more steel., and adjustable.

What, Me Worry?

ren

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #34 on: January 13, 2017, 11:02:15 AM »
I've had good experiences with the Lee PPM, Pro AutoDisk and AutoDrum.
I replaced my Dillon measure and RCBS measures with Lees.
The dryer sheet wipe is a myth - it just makes your powder measure smell flowery.
Only way to get rid of static is to ground it.
If the dryer sheet worked I would been rubbing that on me instead of wearing a grounded wrist strap when I worked as an electronics tech.
« Last Edit: January 13, 2017, 11:43:19 AM by ren »
Deeds Not Words

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #35 on: January 13, 2017, 11:03:23 AM »
That's something interesting to know. You figure it's public information, can be obtained from buying a book and viewed on a website.  ???
Many feel you should patronize the reloading companies and buy their manuals. Some reloading groups I'm in allow it. Some don't.

Check text


Sent from my iPhone using Tapatalk

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #36 on: January 13, 2017, 11:57:18 AM »
I've had good experiences with the Lee PPM, Pro AutoDisk and AutoDrum.
I replaced my Dillon measure and RCBS measures with Lees.
I use my Lee turret press exclusively for reloading pistol cartridges. And I use the Lee Pro Auto Disk. It works well with all the fine grain powders I use. I get very consistent results. It does not work as well with Trail Boss, however. I get much more inconsistent results but good enough for most of what I am reloading. I have never tried using it with rod type powders.
I use my RCBS powder measure when I am reloading for rifle cartridges as it deals with the rod type powders pretty well IMHO. But I only use it for reloading plinking or ammo that I am not looking for a certain amount of precision. For that I measure each load individually using my RCBS Charge Master auto powder and scale. Also, it does not work at all with Trail Boss when throwing rifle size charges.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #37 on: January 13, 2017, 12:07:51 PM »
...
Suggestion....
You spend plenty on the guns and reloading stuff.
Maybe better replace the Lee powder measure with something with less plastic,more steel., and adjustable.

I haven't had any real problems with my Lee progressive. Although Henry is selling his Dillon auto drive 1050xl if you're interested.  :thumbsup:  ;D

I also have a Dillon 450b if that counts, but haven't found it in me yet to buy the 550 conversion kit since the Lee's working pretty good.

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #38 on: January 13, 2017, 12:09:08 PM »
Many feel you should patronize the reloading companies and buy their manuals. Some reloading groups I'm in allow it. Some don't.

Check text


Sent from my iPhone using Tapatalk
I use a lot of Sierra bullets so I bought their manual only for that reason. I also purchased a large amount of Hornady bullets thinking they were going to shoot well out of my guns and so I purchased a Hornady manual as well. Then I found out that the Hornady bullets I bought do not shoot as well as the Sierra, Speer and Bergers I was using. I don't touch that manual much any more. I inherited a Lee and a Lyman manual as well. I also bought the Lyman Cast Bullet and AR-15 manuals. Plus I have all kinds of PDF's and booklets I printed out from the Internet.

As far as patronizing the reloading companies, I don't care. If you can get it free, so be it. I am more than happy to take a pic out of a page and send it to someone.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #39 on: January 13, 2017, 12:09:15 PM »
I've had good experiences with the Lee PPM, Pro AutoDisk and AutoDrum.
I replaced my Dillon measure and RCBS measures with Lees.
The dryer sheet wipe is a myth - it just makes your powder measure smell flowery.
Only way to get rid of static is to ground it.
If the dryer sheet worked I would been rubbing that on me instead of wearing a grounded wrist strap when I worked as an electronics tech.

Noted.  :thumbsup: