.223/5.56 MIL Re-loads / Chrono (Read 42954 times)

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #60 on: January 14, 2017, 05:33:42 PM »
So you're using the exact bullet, case, primer, and rifle they use? If not, it's prudent to start lower to make sure, IMHO.

Thanks for your honest opinion.

Noted.

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #61 on: January 14, 2017, 05:57:22 PM »
, I tried 62 gn I bought from WGS with Varget and wasn't good. I was surprised when the 69 gn worked well.

If it's the 62gr Armscor bullets from WGS, they were only good for making noise for me.

ren

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #62 on: January 14, 2017, 06:10:57 PM »
I plan to be there tomorrow if you want to use my chrono.
Deeds Not Words

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #63 on: January 14, 2017, 06:13:08 PM »
If it's the 62gr Armscor bullets from WGS, they were only good for making noise for me.
I bought 200 of those bullets and gave away 175. The batch I bought were so bad the cannelures were at different heights. So even though I seated each bullet to the same depth the cannelure was never in the same place on any 2 cartridges. I first thought I messed up my brass cases. Turns out all cases were within 0.01" of each other. But the cannelure was at different heights. I tried shooting them working up my loads and I couldn't get good groups out of my Remington 700 bolt gun. After the 25 I loaded I realized they were crap and gave away the 175 I had left.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #64 on: January 14, 2017, 06:27:33 PM »
I used up the 100 I bought from oldfart but don't intend to get anymore. Last November, I tried 62 gn I bought from WGS with Varget and wasn't good. I was surprised when the 69 gn worked well.
The 62gr bullets that WGS sells in small 100 round plastic bags are made by Armscor and are crap if you are looking for an accurate bullet. For me they were not even accurate enough at 100 yds to use as a plinking round.

The 69gr Noslers are high quality bullets and should shoot very well out of most guns.

If you want to try something that weighs in the mid 60's range I load for both the Sierra 63gr and 65gr bullets and for the price are about as accurate as the Sierra 69gr Match Kings I also load for. At a lower price. Both my Remington 700 bolt gun and my AR shoot these very well. 
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #65 on: January 14, 2017, 06:54:55 PM »
The 62gr bullets that WGS sells in small 100 round plastic bags are made by Armscor and are crap if you are looking for an accurate bullet. For me they were not even accurate enough at 100 yds to use as a plinking round.

The 69gr Noslers are high quality bullets and should shoot very well out of most guns.

If you want to try something that weighs in the mid 60's range I load for both the Sierra 63gr and 65gr bullets and for the price are about as accurate as the Sierra 69gr Match Kings I also load for. At a lower price. Both my Remington 700 bolt gun and my AR shoot these very well.

Exactly my experience!! Armscor is rubbish. I have way better results with Hornady 55 FMJBT and SP as a plinking round and are cheaper. 65 SGKs are brutal accurate.

Please post your resluts with the 55 X-Tremes.

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #66 on: January 14, 2017, 07:01:04 PM »
Exactly my experience!! Armscor is rubbish. I have way better results with Hornady 55 FMJBT and SP as a plinking round and are cheaper. 65 SGKs are brutal accurate.

Please post your resluts with the 55 X-Tremes.

If it isn't too hot at 27.2 I'll fire a bunch. 👍🏻

Ill be on scholfield tomorrow to give these a whirl.

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #67 on: January 14, 2017, 07:09:53 PM »
That's good to know because at first I thought my rifle might not like the heavier bullets.

I bought 200 of those bullets and gave away 175. The batch I bought were so bad the cannelures were at different heights. So even though I seated each bullet to the same depth the cannelure was never in the same place on any 2 cartridges. I first thought I messed up my brass cases. Turns out all cases were within 0.01" of each other. But the cannelure was at different heights. I tried shooting them working up my loads and I couldn't get good groups out of my Remington 700 bolt gun. After the 25 I loaded I realized they were crap and gave away the 175 I had left.

I bought 200 rounds from Cabelas and they were similarly crap with different lengths. For awhile, I thought there was something wrong with my seating die. I had seated 80 of the 100 before I figured out the deal. I sorted the remainder of the bullets with my caliper and seated the last 20. At the range, those were the only ones that shot consistently.
http://www.cabelas.com/catalog/product.jsp?productId=705231&categoryId=0&parentCategoryId=0&subCategoryId=0&indexId=0&itemGUID=a085bbfdac108453725d51a0cbf74cb4&destination=%252Fuser%252Forder_details.cmd%253Fid%253DvPbe6RdE9JCwTnDeUBdR%25252BQ%25253D%25253D%2526key%253Dc3168de4a7fa4df2848d47048e18d26e
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Inspector

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #68 on: January 15, 2017, 05:38:53 AM »
That's good to know because at first I thought my rifle might not like the heavier bullets.

I bought 200 rounds from Cabelas and they were similarly crap with different lengths. For awhile, I thought there was something wrong with my seating die. I had seated 80 of the 100 before I figured out the deal. I sorted the remainder of the bullets with my caliper and seated the last 20. At the range, those were the only ones that shot consistently.
http://www.cabelas.com/catalog/product.jsp?productId=705231&categoryId=0&parentCategoryId=0&subCategoryId=0&indexId=0&itemGUID=a085bbfdac108453725d51a0cbf74cb4&destination=%252Fuser%252Forder_details.cmd%253Fid%253DvPbe6RdE9JCwTnDeUBdR%25252BQ%25253D%25253D%2526key%253Dc3168de4a7fa4df2848d47048e18d26e

I never tried Remington or Winchester bullets. When I first started reloading some 25+ years ago, I lived near the Sierra Bullets manufacturing plant. I would get blems very cheap. They sold them by the pound. They shot very well. So I have been a Sierra fan for a very long time. Lately, I have been experimenting with Speer bullets and I have had some good results with them as well.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #69 on: January 15, 2017, 08:36:47 AM »
So does anyone want 100 crappy bullets at various lengths and inconsistent tips? Only cost me $11 with free shipping but they're yours if you want them...

I never tried Remington or Winchester bullets. When I first started reloading some 25+ years ago, I lived near the Sierra Bullets manufacturing plant. I would get blems very cheap. They sold them by the pound. They shot very well. So I have been a Sierra fan for a very long time. Lately, I have been experimenting with Speer bullets and I have had some good results with them as well.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #70 on: January 15, 2017, 06:02:23 PM »
Did you go?

If it isn't too hot at 27.2 I'll fire a bunch. 👍🏻

Ill be on scholfield tomorrow to give these a whirl.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #71 on: January 15, 2017, 06:21:38 PM »
Did you go?

50/50, although I lost 2. Oh well, it's 223, haha.

Chambered well, locks bolt, didn't noticed any of the rounds showing signs of over pressure. However, shot all 50 standing with an ACOG at a silhouette so I didn't take into account any type of accuracy.

Primers all still in, goes bang and not boom!




 :thumbsup: :shaka:

Bushido

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #72 on: January 15, 2017, 07:23:17 PM »
Nice!!

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #73 on: January 15, 2017, 07:32:58 PM »
Sweet. What's your next load gonna be?
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #74 on: January 15, 2017, 08:34:33 PM »
Sweet. What's your next load gonna be?

Friend suggest to try 26gr and I can save powder every 27th bullet, lol.

Might try stick these on a bench with a scope next time just for fun.

 :shake:

rklapp

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #75 on: January 15, 2017, 09:38:35 PM »
Friend suggest to try 26gr and I can save powder every 27th bullet, lol.

Might try stick these on a bench with a scope next time just for fun.

If you're gonna try different powder loads, you might as well try several and test for accuracy, maybe between 25 and 27. Then you can try different powders and bullets and primers and seating depth and...

Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #76 on: January 15, 2017, 09:41:17 PM »
If you're gonna try different powder loads, you might as well try several and test for accuracy, maybe between 25 and 27. Then you can try different powders and bullets and primers and seating depth and...



Just plinking loads, not too concerned with 55gr xtremebullets being accurate, lol.

Heavies

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #77 on: January 18, 2017, 05:49:40 PM »
Looks good!

TooFewPews

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #78 on: January 18, 2017, 06:59:28 PM »
i still don't quite understand the OCW procedure.  can someone please explain the process to me so i can work up some decent plinking loads?  i read the science and it seems to make sense.  i'm just not too keen on the procedure.

Bullet:  Hornady 55 gr SP and Hornady 55 gr FMJBT w/ cannelure
Powder:  IMR 8208 XBR
Primer:  CCI SRP
Case:  Lake City

Kalen

Re: .223/5.56 MIL Re-loads / Chrono
« Reply #79 on: January 18, 2017, 07:12:40 PM »
i still don't quite understand the OCW procedure.  can someone please explain the process to me so i can work up some decent plinking loads?  i read the science and it seems to make sense.  i'm just not too keen on the procedure.

Bullet:  Hornady 55 gr SP and Hornady 55 gr FMJBT w/ cannelure
Powder:  IMR 8208 XBR
Primer:  CCI SRP
Case:  Lake City

OCW procedure?