Lyman 55 powder loader (Read 9201 times)

rklapp

Lyman 55 powder loader
« on: March 28, 2017, 01:50:38 PM »
So I bought this to replace my Lee but I can't figure out how to make it work reliably. Can anyone help me with it? TIA

https://www.amazon.com/Lyman-7767783-Powder-Measure/dp/B000N8LHD8
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

mrgaf

Re: Lyman 55 powder loader
« Reply #1 on: March 29, 2017, 11:22:14 PM »
So I bought this to replace my Lee but I can't figure out how to make it work reliably. Can anyone help me with it? TIA

https://www.amazon.com/Lyman-7767783-Powder-Measure/dp/B000N8LHD8

Had an RCBS that was giving me consistency probs. Read somewhere that static may be the culprit and to wipe the outside of the plexiglas hopper with a dryer sheet. Seemed to help. I also "tap" the side of the measure a couple of times while the handle is up. Hope this provides a fix for you.  :shaka:
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

rklapp

Re: Lyman 55 powder loader
« Reply #2 on: March 30, 2017, 07:33:02 AM »
Had an RCBS that was giving me consistency probs. Read somewhere that static may be the culprit and to wipe the outside of the plexiglas hopper with a dryer sheet. Seemed to help. I also "tap" the side of the measure a couple of times while the handle is up. Hope this provides a fix for you.  :shaka:

I think that's most of the problem. I had wiped everything I could with the drier sheet. After I posted, I took it apart and noticed there was buildup of powder in the bottom tube. I'll try the loader again with passing the drier sheet through the tube. Thanks.  :thumbsup:
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

ren

Re: Lyman 55 powder loader
« Reply #3 on: March 30, 2017, 08:15:13 PM »
the dryer sheet is a myth..it just makes your hopper smell good. I tried that with many hoppers to no difference. The process that works for me is running powder through it a few times. The way to get rid of static is to ground the hopper.
Deeds Not Words

whynow?

Re: Lyman 55 powder loader
« Reply #4 on: March 30, 2017, 08:55:20 PM »
the dryer sheet is a myth..it just makes your hopper smell good. I tried that with many hoppers to no difference. The process that works for me is running powder through it a few times. The way to get rid of static is to ground the hopper.
I peformed the dryer sheet ritual on my Redding powder drop but also ran powder to coat the insides.   Don't have problems with the type of powder I use, but I think that most areas in HI, wouldn't have too much issues with static because of the humidity. 

mrgaf

Re: Lyman 55 powder loader
« Reply #5 on: March 30, 2017, 10:24:35 PM »
the dryer sheet is a myth..it just makes your hopper smell good. I tried that with many hoppers to no difference. The process that works for me is running powder through it a few times. The way to get rid of static is to ground the hopper.
Interesting.... it worked for me. Running flake powder noticed the inside of the hopper had flakes hanging onto the inside surface of the hopper. After wiping down the hopper, no more. Same with my Dillon powder measure. Heck who am I to argue  :worship: if you say it's "myth, it must be....
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

rklapp

Re: Lyman 55 powder loader
« Reply #6 on: March 30, 2017, 11:39:42 PM »
I have a little bit of A1680 left to run through a couple times after using a drier sheet. I could also use the 700x. Thanks for the tips guys.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

mrgaf

Re: Lyman 55 powder loader
« Reply #7 on: March 31, 2017, 06:53:02 AM »
I have a little bit of A1680 left to run through a couple times after using a drier sheet. I could also use the 700x. Thanks for the tips guys.
It will smooth out with use. Key is being consistent too. Some folks wil drop a few grains below thier desired weight then trickle the last few. Depends on you. Good luck! 🍀  :geekdanc:
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

rklapp

Re: Lyman 55 powder loader
« Reply #8 on: March 31, 2017, 09:50:29 AM »
It will smooth out with use. Key is being consistent too. Some folks wil drop a few grains below thier desired weight then trickle the last few. Depends on you. Good luck! 🍀  :geekdanc:
Makes me wonder what's the point of using a loader when I could use a simple scoop and trickle the rest. It's the most accurate but time consuming if loading a batch. The lee loader is relatively accurate. Unfortunately, the plastic was starting to wear out with use. I'm hoping the Lyman will last longer.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

mrgaf

Re: Lyman 55 powder loader
« Reply #9 on: March 31, 2017, 12:46:04 PM »
Makes me wonder what's the point of using a loader when I could use a simple scoop and trickle the rest. It's the most accurate but time consuming if loading a batch. The lee loader is relatively accurate. Unfortunately, the plastic was starting to wear out with use. I'm hoping the Lyman will last longer.

Spoke to a good friend of mine (and my reloading mentor) in Alaska today who's been reloading for over 50 years! He said the dryer sheets help but  give your measure time to break in and, as he puts it, let the "powder dust" do its thing and smooth out the measure. Make sure the inside is clean and free of any factory gunk or film but, he added that none are absolutely perfect, even bench rest measures will vary a little bit. Your key is being consistent in the operation of your measure get into a "habit". There are so many factors that can affect the accuracy of a measure. Like I said earlier, trickle to the exact load amount you want. From what I've been told factories load by volume, not weight
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

ren

Re: Lyman 55 powder loader
« Reply #10 on: March 31, 2017, 06:24:41 PM »
Interesting.... it worked for me. Running flake powder noticed the inside of the hopper had flakes hanging onto the inside surface of the hopper. After wiping down the hopper, no more. Same with my Dillon powder measure. Heck who am I to argue  :worship: if you say it's "myth, it must be....

I'd say from my experience it's a myth. I'm not an authority or expert on things. It didn't work for me but my hoppers smelled really fresh like Doug E. Running powder through them a few times was the method that worked for me. DIllon, RCBS, Lee
Deeds Not Words

rklapp

Re: Lyman 55 powder loader
« Reply #11 on: March 31, 2017, 11:29:45 PM »
I was playing around with it today (because I have nothing better to do on a Friday night, right?) I washed the dispensing tubes with rubbing alcohol, dried, and passed the drier sheet through. I don't see any clingers so appears to be working. I played with the A1680 then switched over to ARcomp in anticipation of my next 223 batch. The A1680 usually sticks to everything but not when I use the drier sheet. I wonder what the sheet residue does to the powder?

Some of the ball powder gets stuck along the metal insert. It seems impossible to remove all of the old powder without completely washing it out and waiting for it to dry. Overall, the consistency is +/- 0.2 gn so still have some practice to do. I'm also still not sure if the new loader is worth the replacement of my old Lee loader.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

ren

Re: Lyman 55 powder loader
« Reply #12 on: April 01, 2017, 08:41:37 AM »
I was playing around with it today (because I have nothing better to do on a Friday night, right?) I washed the dispensing tubes with rubbing alcohol, dried, and passed the drier sheet through. I don't see any clingers so appears to be working. I played with the A1680 then switched over to ARcomp in anticipation of my next 223 batch. The A1680 usually sticks to everything but not when I use the drier sheet. I wonder what the sheet residue does to the powder?

Some of the ball powder gets stuck along the metal insert. It seems impossible to remove all of the old powder without completely washing it out and waiting for it to dry. Overall, the consistency is +/- 0.2 gn so still have some practice to do. I'm also still not sure if the new loader is worth the replacement of my old Lee loader.

Further reading, I found this:


I also read that there is some kind of cationic chemical that are in anti-static dryer sheets.
I thought about it further and the difference between our usage and in dryers is the presence of heat.
In my case, it didn't work sufficiently.
Deeds Not Words

mrgaf

Re: Lyman 55 powder loader
« Reply #13 on: April 01, 2017, 12:17:04 PM »
Further reading, I found this:


I also read that there is some kind of cationic chemical that are in anti-static dryer sheets.
I thought about it further and the difference between our usage and in dryers is the presence of heat.
In my case, it didn't work sufficiently.
Hmmm maybe putting a dryer sheet in a dryer for a minute or so to heat it up somewhat but then again your idea with the spray is more practical! :thumbsup:
To argue with a person who has renounced the use of reason is like administering medicine to the dead.  Thomas Paine.

No man can get rich in politics unless he is a crook.  It cannot be done. Harry Truman

Only good liberal is one taking a dirt nap.

rklapp

Re: Lyman 55 powder loader
« Reply #14 on: April 02, 2017, 01:39:41 PM »
I loaded 40 rounds and still not happy with it. With the Lee Loader, I would load 5 then check with the scale. Maybe after 20, the loader was slightly off so I adjust the loader once and carry on. With the Lyman, I had to check each round with the scale. It was consistent for 2 or 3 then was off, and it would take a couple tries to get the loader back to the correct measurement. There are two screws on the Lyman that clamp the three sliders into place but they frequently become loose. If I have to measure each load, I might as well skip the loader and trickle each load. I have 90 days to return the Lyman to Cabela's with only a $7.50 shipping fee.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

rklapp

Re: Lyman 55 powder loader
« Reply #15 on: April 17, 2017, 06:32:19 PM »
So I returned the Lyman and got the RCSB instead. I was having trouble with it then remembered the static sheet and now works great. Not sure yet if it's any better than the $30 Lee loader. The problem is that it arrived with a crack in the plastic reservoir and nozzle. Brownell is sending me a new one and gave me a UPS label. That's more like it.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Inspector

Re: Lyman 55 powder loader
« Reply #16 on: April 19, 2017, 06:34:43 AM »
I use the RCBS with baffle and micrometer installed. I'm happy with the results I get with it. For the reloading I do it works fine. If I want better control over the load I use my RCBS chargemaster.

When reloading pistol I usually use the Lee auto disk powder measure in my turret press. When using the same flake or ball type powder in either powder measure the RCBS meters out the powder a little more accurately. I have to admit the Lee auto disk has a lot of plastic and feels cheap but I have loaded 1,000's of rounds with it. It is accurate and reliable enough for me. I am particular about reliability and repeat-ability. The Lee auto disk also allows me to reload 300+ rounds an hour using the turret press. I never load a cartridge without first seeing if powder dropped into the case. And only once in 1,000's of rounds has the Lee auto disk ever not dropped a proper charge.

If you are looking to get a measure that will give you 0.1 +/- accuracy most of the time the RCBS with baffle and micrometer will do so with ball or flake powders that I use like Titegroup and H110. Different powders will act differently in each measure so that this with a grain of salt. All bets are off when using rod type powders with it. I found it still does a decent job with powder like Varget and IMR 4198 but the range of accuracy goes up approximately +/- 0.2  grains. For most of my plinking loads that's fine.

I have never had a static cling problem with any of my equipment.

This is just my experience, YMMV.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

rklapp

Re: Lyman 55 powder loader
« Reply #17 on: April 19, 2017, 08:15:44 AM »
I use the RCBS with baffle and micrometer installed. I'm happy with the results I get with it. For the reloading I do it works fine. If I want better control over the load I use my RCBS chargemaster.
"Gosh, you've... really got some nice toys here."

Quote
When reloading pistol I usually use the Lee auto disk powder measure in my turret press. When using the same flake or ball type powder in either powder measure the RCBS meters out the powder a little more accurately. I have to admit the Lee auto disk has a lot of plastic and feels cheap but I have loaded 1,000's of rounds with it. It is accurate and reliable enough for me. I am particular about reliability and repeat-ability. The Lee auto disk also allows me to reload 300+ rounds an hour using the turret press. I never load a cartridge without first seeing if powder dropped into the case. And only once in 1,000's of rounds has the Lee auto disk ever not dropped a proper charge.
If you are looking to get a measure that will give you 0.1 +/- accuracy most of the time the RCBS with baffle and micrometer will do so with ball or flake powders that I use like Titegroup and H110. Different powders will act differently in each measure so that this with a grain of salt. All bets are off when using rod type powders with it. I found it still does a decent job with powder like Varget and IMR 4198 but the range of accuracy goes up approximately +/- 0.2  grains. For most of my plinking loads that's fine.
I agree about the Lee Loader. I was having good results yesterday with the RCBS and Tac powder. I would reweigh every fifth round with slight variances which is to be expected as the powder gets used. I'll get the baffle for it. The extruded powders like Varget are a problem but I tend to use the trickler method for those anyways.

Quote
I have never had a static cling problem with any of my equipment.
This is just my experience, YMMV.
I think it's helpful for the initial use of the loader to keep the ball powder from sticking to the sides, especially the plastic dispensing tube.
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

Inspector

Re: Lyman 55 powder loader
« Reply #18 on: April 19, 2017, 11:17:42 AM »
...I agree about the Lee Loader....
Hey RK,

I got a question for you. You keep calling your Lee powder measure the "Lee Loader". To me the Lee Loader is a cartridge reloading tool, not a powder measure. This is what I know as the "Lee Loader":
http://leeprecision.com/reloading-kits/lee-loader-pistol/

Lee makes 3 different basic auto powder measures. They make the auto disk, the pro auto disk which is the one I have. And they make the auto drum powder measure:
http://leeprecision.com/powder-handling/automatic-powder-measures/

And they make 2 Bench/Stand Mounted Powder Measures. The Perfect Powder Measure and the Deluxe Perfect Powder Measure:
http://leeprecision.com/stand-mounted-powder-measures/

And of course they make the powder dippers:
http://leeprecision.com/powder-measure-kit.html

So my question is, which Lee powder measure do you have? Thanks!
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

rklapp

Re: Lyman 55 powder loader
« Reply #19 on: April 19, 2017, 04:46:24 PM »
Hey RK,
So my question is, which Lee powder measure do you have? Thanks!
The $22.11 one. I should call it the Lee Measurer but loader is easier for me to say. I also use the dippers when I want ammo for shooting at the metal targets. The slide card is convenient for converting cc to grains.
https://www.amazon.com/Lee-Precision-90058-Perfect-Measurer/dp/B000NTMJLG/ref=sr_1_1?ie=UTF8&qid=1492655889&sr=8-1&keywords=lee+powder+measure
Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/