Reloading 9mm cost? (Read 29922 times)

jc2721

Re: Reloading 9mm cost?
« Reply #20 on: April 10, 2012, 07:13:02 PM »
I never really thought about it but I too don't reload for 9mm, given the cost of buying jacketed bullets.  I used to reload 9mm years ago (Sierra 115 gr. JHC) but over the years I've stockpiled enough 9mm to the point where I don't have to reload for a long time.  Remember when Sports Authority used to sell white box 9mm for $4.99 a box?  Those were the good old days!

I reload for .45, since I shoot mostly lead SWCs and the savings can be substantial.  I'm always hunting around for good deals on ammo, but nowadays if I buy factory ammo it is .22 LR. 

The cost of a good press and dies will be quickly amortized, and once you've recouped the cost of your equipment, it's free!

wirecounter

Re: Reloading 9mm cost?
« Reply #21 on: April 12, 2012, 02:17:58 PM »
Thanks for the link to this company. Prices are VERY good and will help lower the cost of reloading for everyone.

Just a heads up . . . I received the brass in about a week the last time I ordered from them.  But, I ordered some (2k) 9mm brass from them about 2 weeks ago and have not received it yet.

I did a little research and it seems that they get backlogged once in a while (kinda like PD), but you will eventually get your order.  However, unlike PD, they charge your cc immediately even though it may take a month for you to receive your order.  :-\

Inspector

Re: Reloading 9mm cost?
« Reply #22 on: April 12, 2012, 07:20:41 PM »
Just a heads up . . . I received the brass in about a week the last time I ordered from them.  But, I ordered some (2k) 9mm brass from them about 2 weeks ago and have not received it yet.

I did a little research and it seems that they get backlogged once in a while (kinda like PD), but you will eventually get your order.  However, unlike PD, they charge your cc immediately even though it may take a month for you to receive your order.  :-\
I think for me this would be okay as long as they let me know what is going on. I hate companies that charge your card without telling you the item is backordered. Then after a while it doesn't show up you have to contact them and then they act like they did nothing wrong.  >:(

So far I have been pretty lucky with the companies we have mentioned here. They communicate pretty well.  :thumbsup:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Mr. Farknocker

Re: Reloading 9mm cost?
« Reply #23 on: May 08, 2012, 10:17:10 AM »
I just ordered 10k 9mm 124 gr JHP from Precision Delta, but it is back ordered.  I plan to call them on Monday to see how far backordered they are.  The bullets come in boxes of 1k so you are welcome to get a box or two from me if you do not mind waiting, may be a couple of months.  Price per 1k (since I am buying 10k) is $82.00 shipped with no usury.  PM me if you are interested.

With ammo available at prices like that, it's really hard to justify the expense and time of reloading unless you want to fine-tune your ammo for precision shooting.

Inspector

Re: Reloading 9mm cost?
« Reply #24 on: May 08, 2012, 12:35:27 PM »
With ammo available at prices like that, it's really hard to justify the expense and time of reloading unless you want to fine-tune your ammo for precision shooting.
That's not ammo he ordered. Those are just the bullet component. That is $0.082 per bullet plus brass case plus powder plus primer. Powder is about $0.01 and a primer about $0.03. So he is up to $0.12 per round depending on where he got his brass. Lately I have been using a figure of $0.03 per round for new brass ($0.12/casing with 4 uses which makes it $0.03/use). And that goes down further if I use the casing 5 times and even further if I buy used brass and free if you get range brass.

Right now I am reloading at about $0.15 per round and I can get that down to about $0.12 per round if I go with components I don't want to use. That is what I make plinking rounds with. Maybe even $0.10 per round if I went with free range brass. The last sale that OGC had on bulk 9mm ammo was $239/1000 or $0.239 per round for Magtech. At today's prices it is worth reloading for me and getting quality fine tuned ammo for my pistols.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

wirecounter

Re: Reloading 9mm cost?
« Reply #25 on: May 08, 2012, 05:00:31 PM »
That's not ammo he ordered. Those are just the bullet component. That is $0.082 per bullet plus brass case plus powder plus primer. Powder is about $0.01 and a primer about $0.03. So he is up to $0.12 per round depending on where he got his brass. Lately I have been using a figure of $0.03 per round for new brass ($0.12/casing with 4 uses which makes it $0.03/use). And that goes down further if I use the casing 5 times and even further if I buy used brass and free if you get range brass.

Right now I am reloading at about $0.15 per round and I can get that down to about $0.12 per round if I go with components I don't want to use. That is what I make plinking rounds with. Maybe even $0.10 per round if I went with free range brass. The last sale that OGC had on bulk 9mm ammo was $239/1000 or $0.239 per round for Magtech. At today's prices it is worth reloading for me and getting quality fine tuned ammo for my pistols.

That. 

And, I've also noticed that my reloads are not as snappy as factory ammo.

Plus, once you start reloading hollow points for home defense (despite what experts say about using factory ammo only), then your cost goes down from $1+ to $0.25 per round.  Not that I'm stockpiling HD ammo  ::)

Inspector

Re: Reloading 9mm cost?
« Reply #26 on: May 08, 2012, 05:25:55 PM »
That. 

And, I've also noticed that my reloads are not as snappy as factory ammo.

Plus, once you start reloading hollow points for home defense (despite what experts say about using factory ammo only), then your cost goes down from $1+ to $0.25 per round.  Not that I'm stockpiling HD ammo  ::)
That.

I use Titegroup for all of my handgun reloading. And while it is not optimum for my .357 Magnum it is for my 9mm. And if I were to believe the velocity stated in all of my books, I have noticed that using the same weight bullet at the same velocity as factory ammo, my felt recoil is significantly less than factory ammo. I thought it was just me but after a little research on the Internet I believe it is the powder that is causing this.

I am still trying to decide which HD bullet I want to try loading for. Are you loading anything new like Hornady's newest? Or Winchester"s newest? I am thinking of 147gr in 9mm this time over the 124gr I was loading for.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

wirecounter

Re: Reloading 9mm cost?
« Reply #27 on: May 08, 2012, 06:10:38 PM »
I am still trying to decide which HD bullet I want to try loading for. Are you loading anything new like Hornady's newest? Or Winchester"s newest? I am thinking of 147gr in 9mm this time over the 124gr I was loading for.

I've been using Vihtavuori N320 for 9mm, W231 for 38 spl & W296 for 357.  But, the load data for W296 is way off on Hodgdon's Reloading Data Center.  I loaded up a bunch and started with the lowest powder loaded round (21.0 gr) and the primer was pancaked.  I did not shoot anymore and had to pull apart 39 bullets.  I am now loading at 17.0 gr and it may still be a bit hot.

Using Golden Sabre for 9mm 124 gr & Hornady XTP 125 gr for 38 spl & 357 mag.  Cannot find Hornady's latest, Critical Defense, available yet other than as loaded ammo.  Also, got a few Hornady FTX 140 gr for 357.

Inspector

Re: Reloading 9mm cost?
« Reply #28 on: May 08, 2012, 09:02:31 PM »
I've been using Vihtavuori N320 for 9mm, W231 for 38 spl & W296 for 357.  But, the load data for W296 is way off on Hodgdon's Reloading Data Center.  I loaded up a bunch and started with the lowest powder loaded round (21.0 gr) and the primer was pancaked.  I did not shoot anymore and had to pull apart 39 bullets.  I am now loading at 17.0 gr and it may still be a bit hot.

Using Golden Sabre for 9mm 124 gr & Hornady XTP 125 gr for 38 spl & 357 mag.  Cannot find Hornady's latest, Critical Defense, available yet other than as loaded ammo.  Also, got a few Hornady FTX 140 gr for 357.
I am kinda old school when it comes to SD rounds. Bigger (heavier) is better. In 9mm I was buying 124gr SD factory ammo cuz I know my guns prefer that weight bullet. But then it dawned on me I am not trying to get 1"-2" groups at 25yds. So I am re-thinking the 124gr and am considering 147gr this time around. Especially since I am loading them myself this time. The reputation of the .357 125gr JHP is legendary. But I think I will go with 158gr JHP this time since I am loading them myself.

I know this sounds weird but I have had similar issues with the Lyman Reloading Manual. I loaded some .357 with so little Titegroup that it would not ignite reliably and had some squibs and lots of unburned powder. I loaded near the bottom end of their scale but not even the lowest. Sierra and Hornady started the same loading at least 25% heavier powder, same velocity. Then with another loading (lead bullet) my loads were so hot that I was getting terrible leading in my barrel. After looking through the Sierra and Hornady books I found the load was way too hot for lead even though I was at the low end of the range in the Lyman book. Sierra and Hornady books were much lower for a lead bullet. I now rely more on my Sierra and Hornady books and look up Hodgens data on the net. If I can't verify a load from these three sources as being similar I won't load it or I rely on the Sierra data. Sierra seems to have performed more thorough loading in the cartridges I load. For instance in .223 Remington they list loads for a semi-auto (AR type) rifle and much different loadings for a bolt gun.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

mnpfamily

Re: Reloading 9mm cost?
« Reply #29 on: May 09, 2012, 07:59:25 AM »
I don't load for HD, but for range use or USPSA matches, its hard to beat 147grn. bullets and N320.  Very little muzzle flip, and with jacketed bullets, very clean.  I use N320 with 147 grn. CMJ from Montana Gold, and with 200 grn. LSWC from S&S.  I used to use TG, but at 3.3grn. I could pull the handle 3 times before the powder over-filled the case.  A double would be way too easy to overlook.  TG is cheap but I found it caused a little more muzzle rise than Vit when loaded to the same PF.  Its also a bit dirtier even with jacketed, and way smokier with lead.  It will definitely save money when compared to the Vit powders, but for the added safety benefit, I'd rather use a powder that takes up more space in the case.

wirecounter

Re: Reloading 9mm cost?
« Reply #30 on: May 09, 2012, 08:11:31 AM »
Mahalo gentlemen for your "data points."

@mnpfamily - How many times do you reload your pistol brass?  I have seen posts (by competition shooters) of upwards of 20 times.

mnpfamily

Re: Reloading 9mm cost?
« Reply #31 on: May 09, 2012, 08:36:05 AM »
I don't think I'm quite at 20 reloads on my brass yet, but have to be getting close.  I've got a bunch that I can barely make out the headstamp.  With my 9mm reloads, if I use them at a match, I usually just leave them.  There are a lot of open division guys shooting  9mm major, I really don't want to risk picking up their brass by mistake.  For me anyway, I think I lose the brass (even using a brass catcher at the range), before it becomes unusable.  My .45 brass seems to be in better shape than my 9mm though.  It could be because I use the "U" die to resize 9mm and a regular resizing die for .45.

wirecounter

Re: Reloading 9mm cost?
« Reply #32 on: May 09, 2012, 12:42:34 PM »
Cool!  I am no where near that many reloads per case & good to know my brass has more life left.   :thumbsup:

mnpfamily

Re: Reloading 9mm cost?
« Reply #33 on: May 09, 2012, 04:41:13 PM »
One thing you might want to consider though is most who load for USPSA try to get fairly close to just above what's needed to make either minor PF or major PF (while allowing some cushion).  These loads feel a lot softer than factory ammo so this may play a factor in brass life.  Another interesting side note, those pieces of brass that I've reloaded the most have become shorter.  In fact they've shrank enough that I actually had to adjust my seating die a little to keep OAL consistent with load data (I load 9mm a little on the short side to begin with).  I haven't reached this point with the ACP cases yet though.

Inspector

Re: Reloading 9mm cost?
« Reply #34 on: May 09, 2012, 07:49:21 PM »
All this talk of loading self defense rounds and I couldn't wait any longer and I ordered a bunch of Hornady XTP JHP bullets from Cabelas. They were on sale with $5 shipping. So I bought 124gr and 147gr in 9mm and 125gr and 158gr in .357.

So do any of you know if the guys over on the rifle side or the silhouette side will let us shoot into milk jugs stuffed with wet newspaper? I would love to try and do our own bullet expansion and retention tests.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

keoni008

Re: Reloading 9mm cost?
« Reply #35 on: May 10, 2012, 10:48:19 PM »
All this talk of loading self defense rounds and I couldn't wait any longer and I ordered a bunch of Hornady XTP JHP bullets from Cabelas. They were on sale with $5 shipping. So I bought 124gr and 147gr in 9mm and 125gr and 158gr in .357.

So do any of you know if the guys over on the rifle side or the silhouette side will let us shoot into milk jugs stuffed with wet newspaper? I would love to try and do our own bullet expansion and retention tests.
I dont think they will let you shoot anything there!

Inspector

Re: Reloading 9mm cost?
« Reply #36 on: May 11, 2012, 11:53:45 AM »
I dont think they will let you shoot anything there!
Yeah, I figured they won't. But I would love to find somewhere that I can run some tests. I am sure there are a few others here who would like to join in as well.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

wirecounter

Re: Reloading 9mm cost?
« Reply #37 on: May 11, 2012, 09:11:40 PM »
Yeah, I figured they won't. But I would love to find somewhere that I can run some tests. I am sure there are a few others here who would like to join in as well.

May try asking one of the clubs that utilize the shooting bays.

Do you chrony your loads?