Powder Coating (Read 2824 times)

Inspector

Powder Coating
« on: October 18, 2020, 11:42:53 AM »
Tried my first batch of powder coating today...
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

macsak

Re: Powder Coating
« Reply #1 on: October 18, 2020, 11:45:36 AM »
Tried my first batch of powder coating today...

heads

Lihikai

Re: Powder Coating
« Reply #2 on: October 18, 2020, 11:47:00 AM »
What kind of powder coat are you using?

Inspector

Re: Powder Coating
« Reply #3 on: October 18, 2020, 01:04:09 PM »
What kind of powder coat are you using?
The general consensus is that Eastwood Ford Light Blue is the best and easiest to use. So that is what that is. I also ordered their dark green as everyone is saying it coats as well as the Ford Light Blue. Once I get good at this I’ll try some of the colors that appeal to me. I’m still in the learning stage.

I have been following a guy on YouTube named Elvis Ammo (I follow a bunch of others as well) and he came up with a low temp process using this powder coat. I went to Goodwill and bought a decent looking toaster oven. When I tried it this morning I couldn’t get the temp down far enough and melted my boolits! 😂 went back to Goodwill today and bought this filthy dirty toaster oven and at works great! I just have to get the temps adjusted correctly.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

oldfart

Re: Powder Coating
« Reply #4 on: October 18, 2020, 04:52:19 PM »
Are you sizing?
What, Me Worry?

Heavies

Re: Powder Coating
« Reply #5 on: October 18, 2020, 08:31:53 PM »
Looks good!

Inspector

Re: Powder Coating
« Reply #6 on: October 19, 2020, 03:21:51 AM »
Are you sizing?
I have not yet, but I intend to. Just have not got around to it. I bought a Lee swage kit. As soon as I size them I am going to load ‘em up and choot ‘em!

I realized after so many hours of casting, a 2 bullet mold is too small. I will be replacing it with a 6 bullet mold.  :rofl:

So far I am getting pretty good results. Just not as good as I would like. I think I just need some practice.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Inspector

Re: Powder Coating
« Reply #7 on: October 19, 2020, 03:24:03 AM »
Looks good!
Thanks B! The photo makes them look better than in person. But I think they are good enough to shoot.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Rocky

Re: Powder Coating
« Reply #8 on: October 19, 2020, 05:15:15 PM »
The photo makes them look better than in person. But I think they are good enough to shoot.
I wanted to slide a photo of certain "person(s)" in here but you know, "discretion".  :rofl: :rofl: :rofl:
I think it is 2a quote worthy tho.
 :wave:
“I ask you to judge me by the enemies I have made.”
                                                           Franklin D. Roosevelt

Inspector

Re: Powder Coating
« Reply #9 on: October 20, 2020, 01:35:03 AM »
I wanted to slide a photo of certain "person(s)" in here but you know, "discretion".  :rofl: :rofl: :rofl:
I think it is 2a quote worthy tho.
 :wave:
That’s really funny! I didn’t think about what I said until you pointed it out.

Maybe you should start a new thread... with photos...   :rofl:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

oldfart

Re: Powder Coating
« Reply #10 on: October 20, 2020, 05:29:07 AM »
I have not yet, but I intend to. Just have not got around to it. I bought a Lee swage kit. As soon as I size them I am going to load ‘em up and choot ‘em!

I realized after so many hours of casting, a 2 bullet mold is too small. I will be replacing it with a 6 bullet mold.  :rofl:

So far I am getting pretty good results. Just not as good as I would like. I think I just need some practice.
...
If the diameter is pretty close, no need size.
Down side is if they're too big then the ammo may have trouble chambering.
Generally, the less squeezing you do to the bullet, the better the accuracy.
Try it.
What, Me Worry?

Inspector

Re: Powder Coating
« Reply #11 on: October 20, 2020, 06:21:48 AM »
...
If the diameter is pretty close, no need size.
Down side is if they're too big then the ammo may have trouble chambering.
Generally, the less squeezing you do to the bullet, the better the accuracy.
Try it.
I’ll check them out when I have some time. I have been really busy lately so casting and powder coating have gone by the wayside. I think the boolits came out at .360”-.361” out of the mold for a .357/.38. So how close is close? I’m sure the powder coating added another .001”-.002” to the diameter.

BTW, I am using the low heat/temp method of powder coating. I have been reading that bringing the boolits up to 400 degrees softens them bringing the BHN down. So I am trying the low temp of 250 degrees as to keep the BHN up at around 16 where I’m at before the powder coating.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!