Anyone have experience with laser bore sighters? (Read 12163 times)

xer 21

Anyone have experience with laser bore sighters?
« on: January 01, 2013, 07:49:08 PM »
basically, im having a lot of difficulty zeroing in my sights on my rifle because i cant see my impacts on my targets properly at 50 or 100, and i dont have any binoculars strong enough.  i DO know that my sights are WAY off; i have to shoot off target even at 50 yards just to get on paper on an 18 inch wide target, so i thought about getting a laser bore sighter, but even then, at 50 yards, im not sure i'll see it.

if not, are there any indoor ranges i can go to to do this, at say, 25 yards?  or should i just test my luck on seeing the laser at 50 yards? 

im looking at this, by the way.

http://www.amazon.com/exec/obidos/ASIN/B001BVI982/?tag=2ahawaii-20

anyone have thoughts? 

ren

Re: Anyone have experience with laser bore sighters?
« Reply #1 on: January 01, 2013, 07:57:29 PM »
Don't need a laser boresighter. You will need a steady rest, preferably one that can clamp onto your rifle.
Remove the bolt.
Sight your target through the bore.
While keeping your rifle or AR upper still, adjust sights to the target.
Reassemble and shoot a few rounds downrange.
Adjust sights to the impact.
« Last Edit: January 02, 2013, 05:58:15 PM by ren »
Deeds Not Words

Boomah

Re: Anyone have experience with laser bore sighters?
« Reply #2 on: January 01, 2013, 08:04:45 PM »
Howzit xer21,

I’ve used them to help get me on the paper a bit quicker but that’s about it. I do consider them handy, especially when mounting an optic.   IMHO it’s best to actually put a few rounds down range if that's at all possible ;)   As far as not having a decent spotting scope to see points of impact, how about asking a fellow shooter?   Of course that's if ones available (say at Koko Head), I'm thinking most would be more than willing to help  :thumbsup:

HTH a little :shaka:

Boomah

Kingkeoni

Re: Anyone have experience with laser bore sighters?
« Reply #3 on: January 01, 2013, 08:10:43 PM »
X-ring laser bore sighted a couple rifles for me.

They have a kit to do it so you don't have to pay to buy the kit.

They did a good job.

My rifles were on paper at 50 yards, a couple shots and I was spot on at 50 then 100.
Your number one Option for Personal Security is a lifelong commitment to avoidance, deterrence, and de-escalation.

Someday someone may kill you with your own gun, but they should have to beat you to death with it because it is empty.

Pit808

Re: Anyone have experience with laser bore sighters?
« Reply #4 on: January 01, 2013, 08:29:21 PM »
Sounds like you need a spotting scope instead......

As far as the laser, I've used mine a few times and am glad I have one.  I don't take it to the range though, I use it in the house and adjust the optic to the dot on the wall.  It gets me on paper every time  :thumbsup:
chitty chitty bang bang.......

SpeedTek

  • Trade Count: (+44)
  • Hero Member
  • *****
  • Posts: 4749
  • Total likes: 126
  • Car Nut, Machinist, Gunsmith & Monkey
  • Referrals: 2
    • View Profile
    • X-Ring on the WWW
Re: Anyone have experience with laser bore sighters?
« Reply #5 on: January 01, 2013, 08:43:01 PM »
Easiest way to laser bore sight is at 21 feet.

We use the peg board at the shop. Normal scope center to bore is 2". Best to measure your distance. Then set it to that

You should be on paper plus or minus 2" at 50 yards. 

On some flash hiders or comps. They need to be removed if youre using a front laser bore sighter. On the cartridge ones i check the cartridge at 12  3  6. 9 oclock positions to make sure its centered. I prefer the front mount type. But the shaft is prone to bending if you dont store it well

Political Correctness is FOS
I collect M1 Carbines, PM me if youre selling!
& Bolt Action 308s also 10/22 Rugers.
Buying STOCK Ruger 10/22 parts and bits, PM me.
Now doing Vintage VW Parts!

wirecounter

Re: Anyone have experience with laser bore sighters?
« Reply #6 on: January 01, 2013, 08:48:31 PM »
Sounds like you need a spotting scope instead......

+1.

You would need a good laser to see it during the daylight.  I have one (to get me on paper) and I sight it in on my neighbor's house which is roughly 75 yards.

xer 21

Re: Anyone have experience with laser bore sighters?
« Reply #7 on: January 01, 2013, 09:24:02 PM »
thanks for the advice guys.  i might get one just to get me on paper, but yeah, i guess i just have to go and get a spotting scope.

HNL03

Re: Anyone have experience with laser bore sighters?
« Reply #8 on: January 02, 2013, 04:17:21 AM »
Shoot at a rock on the ground, you'll be able to tell if you're high, low, left or right.

Cougar8045

Re: Anyone have experience with laser bore sighters?
« Reply #9 on: January 02, 2013, 06:05:53 AM »
Necessity being the mother of invention, you can get on paper by propping your rifle up on something semi-stable, like a torpedo level and a couple cans of dip.  Then look through the bore at some convenient reference mark, such as a roof vent on a house across the way.  Adjust sights to match and bingo. 



And for the naysayers, this setup got me within an inch of zeroed at fifty yards; piece of cake to work it in from there!   :geekdanc:
I'm just a fluffy white bunny rabbit who lost his way. 

"If a thief be found breaking in, and be smitten that he die, there shall no blood be shed for him. ..."  -Exodus 22:2

drck1000

Re: Anyone have experience with laser bore sighters?
« Reply #10 on: January 02, 2013, 08:00:23 AM »
Necessity being the mother of invention, you can get on paper by propping your rifle up on something semi-stable, like a torpedo level and a couple cans of dip.  Then look through the bore at some convenient reference mark, such as a roof vent on a house across the way.  Adjust sights to match and bingo. 

And for the naysayers, this setup got me within an inch of zeroed at fifty yards; piece of cake to work it in from there!   :geekdanc:
While I don't dip, that's basically what I do.   ;)

I have a laser boresighter as well, but my condo isn't large enough for me to get good results.  I would try it in the hallway, but the neighbors might not appreciate that. 

I usually take a Lead Sled to the range when I am sighting in a gun, so I usually start off by doing a quick boresight at the range and it usually gets me pretty darn close and usually closer than if I had used the laser boresighter in my condo. 

BTW, that's some nice glass you've got on there Cougar!  :thumbsup:

robtmc

Re: Anyone have experience with laser bore sighters?
« Reply #11 on: January 02, 2013, 08:26:14 AM »
As far as the laser, I've used mine a few times and am glad I have one.  I don't take it to the range though, I use it in the house and adjust the optic to the dot on the wall.  It gets me on paper every time  :thumbsup:
I'm with Pit.  How I use mine.  Used it on everything from a .22 conversion to my 870 12 Ga with rifle sights.  Shooting shows it is just close, not an exact science.

I have two of the things that slide into the muzzle.  The Laserlyte I got from Midway is pretty good quality, the laser is concentric with the bore spud.  Bought another cheaper one from Amazon that is a POS.  The laser runout is horrible if you rotate the housing while in the bore.

Cougar8045

Re: Anyone have experience with laser bore sighters?
« Reply #12 on: January 02, 2013, 08:30:57 AM »
While I don't dip, that's basically what I do.   ;)

I have a laser boresighter as well, but my condo isn't large enough for me to get good results.  I would try it in the hallway, but the neighbors might not appreciate that. 

I usually take a Lead Sled to the range when I am sighting in a gun, so I usually start off by doing a quick boresight at the range and it usually gets me pretty darn close and usually closer than if I had used the laser boresighter in my condo. 

BTW, that's some nice glass you've got on there Cougar!  :thumbsup:
Thanks, that was a Christmas present from the girlfriend, who will always and forever be on my "nice" list.  :thumbsup:
I'm just a fluffy white bunny rabbit who lost his way. 

"If a thief be found breaking in, and be smitten that he die, there shall no blood be shed for him. ..."  -Exodus 22:2

DuckFat

Re: Anyone have experience with laser bore sighters?
« Reply #13 on: January 02, 2013, 10:07:14 AM »
basically, im having a lot of difficulty zeroing in my sights on my rifle because i cant see my impacts on my targets properly at 50 or 100, and i dont have any binoculars strong enough.  i DO know that my sights are WAY off; i have to shoot off target even at 50 yards just to get on paper on an 18 inch wide target, so i thought about getting a laser bore sighter, but even then, at 50 yards, im not sure i'll see it.
I had this issue the first time I mounted a scope myself. Problem: the mount was on backwards. Are these iron sights and are they mounted properly? Perhaps get someone with more knowledge to look at it? The guys at SEC identified the problem, remounted the scope, and laser sighted in the store; it was about 1" off from zero when I tried it at the range. Laser bore sights aren't 100% accurate but should get you close enough to where you can zero in a few rounds. Spotting scopes are essential to the process, you gotta see exactly where you're hitting. You shouldn't need to take the bore sight with you to the range.

Cougar's idea is awesome. I'm gonna have to try it next time I'm attaching an optic.  :thumbsup:
What if rhinos are just fat unicorns?

GZire

Re: Anyone have experience with laser bore sighters?
« Reply #14 on: January 02, 2013, 10:55:56 AM »
I have a laser boresighter.  What I do is measure the offset from my scope to the laser.  I adjust windage dead on, but maintain the bore to scope offset.  From there that'll get me on the paper and I just adjust from there.

The other way is to shoot the berm at 100 yards and look for splash.  If you aren't even on the paper it's about impossible to shoot at paper to determine where you are impacting.

xer 21

Re: Anyone have experience with laser bore sighters?
« Reply #15 on: January 02, 2013, 11:24:36 AM »
I had this issue the first time I mounted a scope myself. Problem: the mount was on backwards. Are these iron sights and are they mounted properly? Perhaps get someone with more knowledge to look at it? The guys at SEC identified the problem, remounted the scope, and laser sighted in the store; it was about 1" off from zero when I tried it at the range. Laser bore sights aren't 100% accurate but should get you close enough to where you can zero in a few rounds. Spotting scopes are essential to the process, you gotta see exactly where you're hitting. You shouldn't need to take the bore sight with you to the range.

Cougar's idea is awesome. I'm gonna have to try it next time I'm attaching an optic.  :thumbsup:

they're irons.  at 100 yards, i have to shoot far enough off target to the right just to get on paper, that im shooting about 10-20 inches left.  i mean, im not a great shooter, but i dont think im THAT bad.  also because everyone else who's shot it has been that far left most every time.

338KID

Re: Anyone have experience with laser bore sighters?
« Reply #16 on: January 02, 2013, 12:16:39 PM »
You should ask maybe the guy on the next bench with a higher powered scope to help . At koko head I normaly leave my spotting scope home (too much people) but me and my pops just spot for each other @100 with our scopes . Most times people there are always helpful .
Fast is fine , accuracy is final

robtmc

Re: Anyone have experience with laser bore sighters?
« Reply #17 on: January 02, 2013, 12:27:54 PM »
I have a laser boresighter.  What I do is measure the offset from my scope to the laser.  I adjust windage dead on, but maintain the bore to scope offset.  From there that'll get me on the paper and I just adjust from there.
We had a similar discussion earlier about trajectories and path crossing.  A decent ballistics program will let you enter in sight height over bore, then you look for first zero crossing and laser boresight there.  I have a stop sign 110 yards away that makes a great daytime reflective surface for fine tuning windage.  A small error not seen at 25 yds will be obvious at 110.  Amazing how bright the laser dot is off those stop sign surfaces.

I would agree windage is more important in this process, but so far, it is windage that has needed tweaking mostly when actually shooting.  Elevation with the zero crossing method has been within a inch or less at 100 yds.  Suspect the windage issue is my crappy form when shooting.

GZire

Re: Anyone have experience with laser bore sighters?
« Reply #18 on: January 02, 2013, 03:47:48 PM »
Guys just be careful when aiming your rifles outside of your houses with a laser.  A lot of people may mistake what you are trying to do.

zippz

Re: Anyone have experience with laser bore sighters?
« Reply #19 on: January 02, 2013, 05:57:08 PM »
As everyone said before, either boresight - look through the barrel at something and adjust sights accordingly, and shoot at something on the 100yd berm and have someone spot the round for you.