556. (Read 38185 times)

paka808

556.
« on: February 14, 2015, 03:57:18 PM »
Can you guys give me an idea of how much it would cost to do 556 rounds..cost of equipment and materials.And can I get everything I need on island.Aloha

justin1098

Re: 556.
« Reply #1 on: February 15, 2015, 12:08:19 AM »
depends...

you can get everything on island but it'll cost you.
you can get a lee breechlock kit from amazon with free shipping for 126.99 and dies will another 40 bucks. you will also need a case trimmer ($70) and calipers($30). Powder on island is about 30 to 40 bucks a pound and primers are like 4-5 dollars for 100. bullets are $7-$40 for 100. brass is recyclable so i don't really count that. you will have to ream or swage the the crimp out of the primer pockets. tools are $20 to $80. 

so that's about $350 to make your first 100 rounds. you can spend a lot more or a bit less. if you buy all your tooling on island it will probably be closer to $500.

I advise you to do some research and look at someones setup if you can to figure out what you want and avoid buying things that you will want to upgrade right away. I would recommend a decent electronic scale and a little crow WFT case trimmer to speed up the most tedious parts of loading.

hope that helps

suka

Re: 556.
« Reply #2 on: February 15, 2015, 03:50:30 AM »
Ask yourself first :
buy a full kit or all items seperate
progressive press or single press
press brand and price range
reload from new cases or once fired cases


once fired, 5.56 case necks will stretch (grow) after each shot. So you'll need a trimmer and set of calipers along with a tumbler


please do a bit of research first, there are tons of equipment out there. or you can build your own press.




paka808

Re: 556.
« Reply #3 on: February 15, 2015, 08:57:51 AM »
Thank you guys.I really appreciate the feed back.

jc2721

Re: 556.
« Reply #4 on: February 15, 2015, 10:41:51 AM »
Buy a good reloading manual first.  The reloading equipment you buy will probably last a lifetime (if you buy quality).

The big "expense" in reloading is the time you put into it--if you take shortcuts or are prone to "rush jobs" you'll probably blow something up at best, hurt someone at the worst.  If you look at reloading as a hobby and/or have more time than $$$, then it makes sense.  If you have more $$$ than time, then buying case lots may make more sense.

My .02

justin1098

Re: 556.
« Reply #5 on: February 15, 2015, 01:03:18 PM »
Here is some helpful links

A bunch of articles from sierra that cover a lot especially if you are loading military rifles.
http://www.exteriorballistics.com/reloadbasics/index.cfm

the 223 page on accurateshooter with some good info about components and sierra load data.
http://www.accurateshooter.com/cartridge-guides/223rem/

oldfart

Re: 556.
« Reply #6 on: February 15, 2015, 01:58:27 PM »
Can you guys give me an idea of how much it would cost to do 556 rounds..cost of equipment and materials.And can I get everything I need on island.Aloha
...
What is your goal? Blasting ammo or accuracy ammo?
Also, what kind of rifles are you using?
What is your budget?
What, Me Worry?

paka808

Re: 556.
« Reply #7 on: February 15, 2015, 02:06:32 PM »
It would be a mixture of accuracy and blasting,i will be using this ammo for my scar16 and ar15,and my budget will be around $500.Again thanks for all the help guys, helps me out alot.

justin1098

Re: 556.
« Reply #8 on: February 15, 2015, 03:35:53 PM »
It would be a mixture of accuracy and blasting,i will be using this ammo for my scar16 and ar15,and my budget will be around $500.Again thanks for all the help guys, helps me out alot.

$500 should get you going. Making ammo that shoots accurately in your rifle has more to do with brass prep, attention to detail, and load work-up than how much you spend on tooling.

ren

Re: 556.
« Reply #9 on: February 15, 2015, 03:59:43 PM »
If you decide to go progressive - which I think will fit your needs, WGS has Dillons. I'd suggest the 550B. Great all around machine and works semi progressively. Another one is the Hornady AP. READ about these machines, WATCH THEM in YouTube.
Sorry, the words "research" and "read" get so lost in meaning as they are often wrongly used. When I started the grad program that's one of the the first things we humbly learned. OK <RANT OFF>

Dillons have a good resale value. Reloading rifle cases will require to spend some time in case prep i.e. sizing, trimming etc. A progressive machine or semi (550B) will allow you to complete multiple processes at the same time with one stroke of the lever. Saves time. You can dump powder, seat the bullet and crimp if you wish. Those are the main steps a progressive machine will allow you to do. Sizing is done first, then trimming. I suggest the Giraud TriWay http://www.giraudtool.com/Tri%20Way%20Trimmer.htm It trims, deburrs the cut and chamfers the neck for seating of the bullet.
Deeds Not Words

paka808

Re: 556.
« Reply #10 on: February 15, 2015, 04:12:32 PM »
Thanks ren
I will definitely look up that equipment,and check out some you tube vids

fang23

Re: 556.
« Reply #11 on: February 16, 2015, 04:33:52 PM »
Reloading 5.56? Don't limit yourself.  There are more recipes for .223. Differences in pressure and chamber dimensions. General rule: you can fire 223 in a 5.56 weapon, but most advise against  firing 5.56 in a .223 weapon. Load .223 and don't sweat it.

Do your research first: Check out this book by Christopher Ohland: AR 15 Ammunition Relocating: A beginner's guide....It's available on Amazon. Has specific recommendations and detailed step-by-step guide so that i was able to . load .223 ammo that fired and functioned well in my Savage .223 and ARs on the first try.  Recomends Sierra HPBT 69 grn and Varget, which is just one of a zillion possibilities, but as a good a place to start as any.

Books are cheap. Do your research first: The ABCs of Reloading (now in its 9th edition), the .223 Rem edition of the Loadbooks series (cheap [photocopies of various manufacturers' recommended loads). Agree with JC2721, buy a good reloading manual. Sierra, Nosler, Hornady, Lee, etc. Some manufacturers have information on the Internet, but a lot of the other stuff on the web is worth what you pay for it -- nothing. JC's advice about not rushing or cutting corners is well taken. It's easy to make crappy ammo. Just hope the cost of sloppy reloading doesn't get someone hurt.


You can get started for $500 if you shop carefully, but that will likely be just the beginning of a whole new way to spend your money. I started reloading a few years ago, after the first Obama scare, when 5.56/.223 was scarce and expensive. Bought a 550B from Dillon.and a Wilson hand-crank trimmer, Redding balance beam scale. Used the 550B's powder drop. Spent plenty trying to get it to meter more accurately, and learned that there are many powders and powder measures that work better. Now have a couple of $20 Lee PPMs dedicated to particular loads, among several powder measures. Added a couple of Lee presses and an RCBS Rockchucker. Still use the Dillon  for seating and crimping. BTW, if  you're using once-fired 5.56, add the cost of something to swage out the crimp in the primer pocket. Dillon works for me, but is pricey. Lee stuff is cheap, and might not last, but it's a good way to start on a budget.

 Bottom line: If you're going to handload to save money, you will probably be disappointed. Even if you just spend $500 to get started, you'd have to shoot a lot of rounds to cover the difference between commercial ammo and your handloads. Bullets cost money. Figure 10 to 25  cents a round for a decent .224 pill, plus 4 cents and up for a primer, and about 10 cents for powder (roughly based on  23 grains per round, so about 300 loads from a a pound of powder -- 7000 grains ag $30/lb. Those prices are low if you're buying components locally.   Didn't even include the cost of brass. You're already looking at about  25 cents/round. Commercial ammo is down to about 37.5 cents per round these days.
 HOWEVER, reloading does enable you to tailor ammo exactly for your needs. Once you get the hang of it, you will have the satisfaction of knowing a valuable skill; you will know a heck of a lot more about what happens when you pull the trigger;  you will be less dependent on manufacturers and retailers, and when the next scare happens and ammo becomes unobtainable or stupid expensive, you will be happy.

"If it ain't one thing, it's another."

paka808

Re: 556.
« Reply #12 on: February 16, 2015, 07:23:44 PM »
Reloading 5.56? Don't limit yourself.  There are more recipes for .223. Differences in pressure and chamber dimensions. General rule: you can fire 223 in a 5.56 weapon, but most advise against  firing 5.56 in a .223 weapon. Load .223 and don't sweat it.

Do your research first: Check out this book by Christopher Ohland: AR 15 Ammunition Relocating: A beginner's guide....It's available on Amazon. Has specific recommendations and detailed step-by-step guide so that i was able to . load .223 ammo that fired and functioned well in my Savage .223 and ARs on the first try.  Recomends Sierra HPBT 69 grn and Varget, which is just one of a zillion possibilities, but as a good a place to start as any.

Books are cheap. Do your research first: The ABCs of Reloading (now in its 9th edition), the .223 Rem edition of the Loadbooks series (cheap [photocopies of various manufacturers' recommended loads). Agree with JC2721, buy a good reloading manual. Sierra, Nosler, Hornady, Lee, etc. Some manufacturers have information on the Internet, but a lot of the other stuff on the web is worth what you pay for it -- nothing. JC's advice about not rushing or cutting corners is well taken. It's easy to make crappy ammo. Just hope the cost of sloppy reloading doesn't get someone hurt.


You can get started for $500 if you shop carefully, but that will likely be just the beginning of a whole new way to spend your money. I started reloading a few years ago, after the first Obama scare, when 5.56/.223 was scarce and expensive. Bought a 550B from Dillon.and a Wilson hand-crank trimmer, Redding balance beam scale. Used the 550B's powder drop. Spent plenty trying to get it to meter more accurately, and learned that there are many powders and powder measures that work better. Now have a couple of $20 Lee PPMs dedicated to particular loads, among several powder measures. Added a couple of Lee presses and an RCBS Rockchucker. Still use the Dillon  for seating and crimping. BTW, if  you're using once-fired 5.56, add the cost of something to swage out the crimp in the primer pocket. Dillon works for me, but is pricey. Lee stuff is cheap, and might not last, but it's a good way to start on a budget.

 Bottom line: If you're going to handload to save money, you will probably be disappointed. Even if you just spend $500 to get started, you'd have to shoot a lot of rounds to cover the difference between commercial ammo and your handloads. Bullets cost money. Figure 10 to 25  cents a round for a decent .224 pill, plus 4 cents and up for a primer, and about 10 cents for powder (roughly based on  23 grains per round, so about 300 loads from a a pound of powder -- 7000 grains ag $30/lb. Those prices are low if you're buying components locally.   Didn't even include the cost of brass. You're already looking at about  25 cents/round. Commercial ammo is down to about 37.5 cents per round these days.
 HOWEVER, reloading does enable you to tailor ammo exactly for your needs. Once you get the hang of it, you will have the satisfaction of knowing a valuable skill; you will know a heck of a lot more about what happens when you pull the trigger;  you will be less dependent on manufacturers and retailers, and when the next scare happens and ammo becomes unobtainable or stupid expensive, you will be happy.
yeah I understand what your saying about 556 buying inexpensive right now, thought I would start with 556 because that's what I mostly shoot and work my way to other calibers.thanks for all your input.

oldfart

Re: 556.
« Reply #13 on: February 16, 2015, 08:44:55 PM »
The other guys have covered most all the usual stuff. The only thing I can add is that I recommend loading some ammo with a buddy that already reloads.
You will learn much faster.
What, Me Worry?

paka808

Re: 556.
« Reply #14 on: February 16, 2015, 10:17:57 PM »
The other guys have covered most all the usual stuff. The only thing I can add is that I recommend loading some ammo with a buddy that already reloads.
You will learn much faster.
I will definately do that,i might just blow my self up.lol

Kingkeoni

Re: 556.
« Reply #15 on: February 17, 2015, 04:17:49 AM »
I will definately do that,i might just blow my self up.lol
Your number one Option for Personal Security is a lifelong commitment to avoidance, deterrence, and de-escalation.

Someday someone may kill you with your own gun, but they should have to beat you to death with it because it is empty.

oldfart

Re: 556.
« Reply #16 on: February 18, 2015, 10:05:49 AM »
----
Reminder that I do have a standing invitation to newb reloaders to drop by my house to see how I do my reloading.
I'm more geared to handgun loading but the basic principles are the same.
A number of fellas have taken advantage of the offer.
What, Me Worry?

Bushido

Re: 556.
« Reply #17 on: April 18, 2015, 08:59:31 AM »
Rather than start another "newbie question" thread and my question relates to OP, I'll post here if you don't mind. ---- I've been collecting my reloading equipment for several months now and finally have what I feel I need to drop my first charge. I'm reloading .223 Rem for a bolt gun. Using once fired WCC brass, CCI BR-4 primers, 69grn HPBT Sierra Matchkings. I bought Varget and H335 and was planning to start with H335 and hold the Varget for later use. The data shows 22grns of H335 as the starting load and 24grns being the max load. I was planning to load 20 rounds each of 22grns and increasing by .5grn to a max to 23.5grns for a starting point. I would be looking for overpressure signs along the way. After I find the load that shoots the best in my rifle, I was planning on increasing/ decreasing the charge by .2grns next than .1grn to fine tune and possibly playing with OAL.

My primary reason to reload is for accuracy but cost is also a major factor. I would like to end up with a load similar to Federal Gold Medal Match as my rifle shoots those really well.

With that in mind, I'm open to your thoughts and suggestions.

jonjon

Re: 556.
« Reply #18 on: April 18, 2015, 09:12:12 AM »
----
Reminder that I do have a standing invitation to newb reloaders to drop by my house to see how I do my reloading.
I'm more geared to handgun loading but the basic principles are the same.
A number of fellas have taken advantage of the offer.

old fart helped me out and pointed me in the safe and right direction  :shaka:

Mr. Farknocker

556.
« Reply #19 on: April 18, 2015, 04:02:11 PM »
Rather than start another "newbie question" thread and my question relates to OP, I'll post here if you don't mind. ---- I've been collecting my reloading equipment for several months now and finally have what I feel I need to drop my first charge. I'm reloading .223 Rem for a bolt gun. Using once fired WCC brass, CCI BR-4 primers, 69grn HPBT Sierra Matchkings. I bought Varget and H335 and was planning to start with H335 and hold the Varget for later use. The data shows 22grns of H335 as the starting load and 24grns being the max load. I was planning to load 20 rounds each of 22grns and increasing by .5grn to a max to 23.5grns for a starting point. I would be looking for overpressure signs along the way. After I find the load that shoots the best in my rifle, I was planning on increasing/ decreasing the charge by .2grns next than .1grn to fine tune and possibly playing with OAL.


If your starting load is 22 and max load is 23.5, and you go up in 0.5 gr increments you will only have 4 loads to play with. That's too big a spread in my book to efficiently find the sweet spot on a rifle. Those who load for accuracy know that rifles can have several loads that run well in a particular firearm. For example, my AR shoots well with 23.7 gr of Varget and 24. 0.1 gr can and often does make a significant difference so working up loads for accuracy should be done in smaller increments than 0.5 gr.  Since you can find accurate loads at any point, you may as well start with the starting load and work your way up in 0.1 increments otherwise you'll just end up confusing yourself. For example: say you load 22, 22.5, 23 and 23.5 and then find that 22.5 is the most accurate load.  Then you load up a few more above and below that in increments of .2 gr. so you now have a load of 22.3 and 22.8.  As you continue to look for the best load and make fine adjustments, it gets difficult to keep track of that on paper. My suggestion is that if the Start and Max load is only a two grain difference, start with the starting load and then increase it by 0.1 gr.  Take photos of your groupings and then go home to review them and if necessary, take measurements.

20 round for each load is also way too many rounds to efficiently test each load and may be a waste of bullets and powder if the load turns out to be a loser. You should be able to compare loads with just five shots. 

What I do is make a set of five rounds for each load. This gives me a decent grouping to compare and doesn't clutter the target with holes.

Here are sample photos of .223 using Varget and range brass at 50 yards. I started with 23.5 gr. and worked my way up to 24.2 gr. in 0.1 increments, labeling each load with letters A through H.   As you can see, there are definite changes in accuracy when a load is increased/decreased by just 0.1 gr.





« Last Edit: April 19, 2015, 12:39:53 PM by Mr. Farknocker »