So... I want to cast bullets (Read 26692 times)

justin1098

So... I want to cast bullets
« on: June 02, 2015, 03:34:26 PM »
Want to get into casting my own bullets and I have a few questions for the experienced folks.

Should I buy a bottom pour furnace from lee or one of the lyman starter kits with the ladle? There is not a huge difference in price but I would like to buy once.

I plan on casting for 300 BLK and 30 carbine. Is lyman #2 a good alloy for those? I plan on just buying alloy and not chasing scrap lead and wheel weights that aren't made anymore.

Is there a good online source that explains the basics of alloys?

Does anyone want to get rid of any casting stuff for a reasonable price?

That is all
thanks

oldfart

Re: So... I want to cast bullets
« Reply #1 on: June 02, 2015, 11:51:42 PM »
I have a feeling that it might be more trouble than it's worth.
You would need to consume mass quantities to justify the cost, time, and hassle.
I cast and shoot my 45 bullets, but those are easy compared to rifle bullets.
« Last Edit: June 03, 2015, 02:36:38 AM by oldfart »
What, Me Worry?

justin1098

Re: So... I want to cast bullets
« Reply #2 on: June 03, 2015, 06:14:27 AM »
The time and hassle is most of the reason that I want to do it. Same reason that I built a 300BLK. Same reason that I handload everything that I shoot.

oldfart

Re: So... I want to cast bullets
« Reply #3 on: June 03, 2015, 11:34:58 AM »
The time and hassle is most of the reason that I want to do it. Same reason that I built a 300BLK. Same reason that I handload everything that I shoot.
==========
ok then...
Read books- see the pic attached
See my video on youtube for an overview of my process: 
Decide what bullets you want to cast and see if you can find the moulds.
Then decide how you are going to size and lubricate them. ie what machine or method.
The conventional bullet lube is applied via lubrisizer or melting the lube in a pan and using a cookie cutter device of some sort.
LEE sells a thing called tumble lube, but I have not tried it.
You might be able to use the new generation of plastic coatings instead of conventional lube.
See S and S casting for a sample of plastic coated 30 carbine bullets
For hi-speed lead bullets, a gas check is usually applied to the base via lubrisizer machine.
Lyman #2 is a standard alloy but you can also blend your own mix with scrap lead and other stuff you find locally.
Last year I went to a recycling place in kapolei and bought soft scrap lead. I think they had either wheel weights or Linotype there also.
I created a spreadsheet that can calculate the approximate composition of a mix by inputting the metal you have available.
RE: melting pot=> I only used bottom pour. It works for me. But ladle pouring is fine too and you don't have to fiddle around with the valve.



 
What, Me Worry?

Mr. Farknocker

Re: So... I want to cast bullets
« Reply #4 on: June 03, 2015, 11:48:41 AM »
The time and hassle is most of the reason that I want to do it. Same reason that I built a 300BLK. Same reason that I handload everything that I shoot.

You're like me. You like to tinker and you derive a great deal of pleasure doing things by yourself.

I've used a ladle and have never used a bottom pour. I wanted to buy a bottom pour but the ladle was cheaper. I figured if I got serious with making my own bullets, I'd invest in a bottom pour. Well, I've made thousands of bullets since then with my ladle and am satisfied with it.

The only draw back I see with ladles is that your arm may tire from scooping and pouring. The fact that the ladle sticks out of the melting pot also presents a slight danger if you move to quickly and hit the ladle sending molten led up into the air and on to your skin. Other than that, the fact that the mold is right in front of you instead of under a pot makes it easy to see where to pour and when to stop.  I started off with a cheap lee ladle and made thousands of rounds with it. It worked but the ladle really was too small to do any serious volume. If you decide to go the ladle route, make sure the ladle that comes with the system is a decent size. This will reduce the number of dips you need to fill the mold cavities. The RCBS Lead Ladle turned out to be the perfect size for my Lee six cavity molds.

The only complaint I've heard about the bottom pour pots is that they may drip or leak due to contamination of the valve or debris being lodged in the pour valve. Aside from that, the only thing I can think of is that the mold may be obstructed by the pot itself forcing the user to position his/her body in a manner which would allow the user to alignment the mold and the pour spout. I have no experience with a bottom pour to know whether this really is an issue or not.

In any event, you can't go wrong with either system. I went with the ladle system because it was cheaper for me. I went to the salvation army, bought some muffin pans, two stainless steel pots and used a portable stove I "borrowed" from my folks. Total setup cost was probably under $15.  Throw the RCBS ladle in their for an added cost of $25 and you got yourself a $40 lead melting system.

Here I am demonstrating how I use the RCBS ladle, a six cavity mold and my ole' cheapy lead melter.



Good luck.



Mr. Farknocker

Re: So... I want to cast bullets
« Reply #5 on: June 03, 2015, 11:51:08 AM »
double post

oldfart

Re: So... I want to cast bullets
« Reply #6 on: June 03, 2015, 12:35:33 PM »
Good vid mr fark.
I see you water quench.
I used to water quench to increase hardness but I feel I get a little better accuracy by not quenching.
Still using the pan lube method?
My old, old rcbs pro melt pot wore out so I bought the 20 lb lee bottom pour pot.
Have not tried it yet, tho...

Maybe I ought to try fire that thing up this month since I took off some vac days.
What, Me Worry?

Inspector

Re: So... I want to cast bullets
« Reply #7 on: June 03, 2015, 02:11:35 PM »
I realize most everything you will need to know is already on the internet. And for free. But I will suggest buying the Lyman Cast Bullet manual anyway. Pretty Much everything you need to know plus it has loading information strictly for lead bullets. Bought mine on Amazon.
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Q

Re: So... I want to cast bullets
« Reply #8 on: June 03, 2015, 02:37:33 PM »
.
« Last Edit: March 05, 2021, 03:32:05 PM by Q »

Mr. Farknocker

Re: So... I want to cast bullets
« Reply #9 on: June 03, 2015, 03:07:53 PM »
Good vid mr fark.
I see you water quench.
I used to water quench to increase hardness but I feel I get a little better accuracy by not quenching.
Still using the pan lube method?
My old, old rcbs pro melt pot wore out so I bought the 20 lb lee bottom pour pot.
Have not tried it yet, tho...

Maybe I ought to try fire that thing up this month since I took off some vac days.

I started off water quenching because it supposedly made for harder bullets but then came across some literature that said it really doesnt. There's also some literature out there that states that the lead continues to harden over the next few weeks and that reloaders often mess that process up and end up with "soft" bullets by sizing the bullets weeks or even months after they've been cast. In any event, I don't know what to believe.  At this point, I simply water quench because the water helps to harden the cast bullets instantly before they can deform by striking the bottom of the container or in most cases, other lead bullets, when they fall from the mold.  I haven't gotten around to testing whether my firearms perform better one way or the other. 

Mr. Farknocker

Re: So... I want to cast bullets
« Reply #10 on: June 03, 2015, 03:08:56 PM »
If you are just starting, get the standard pot to play around with.

Once you are more experienced and should you decide to continue, invest in the bottom pour.

This is my approach to just about every new thing I get into.

justin1098

Re: So... I want to cast bullets
« Reply #11 on: June 03, 2015, 04:57:40 PM »
Thanks guys.
I am at the point where I have watched lots of youtube videos, Oldfart's included, but I haven't spent any money yet. My next step is books, I'm thinking the lyman books. I don't plan on doing any high volume production. I like to take my time be methodical. It keeps me from getting ahead of myself and making mistakes.

Thanks Oldfart, for the info on the scrap. I will probably contact you to get the details later on when I commit to this hobby.

That's a great point about the ladle sticking out of the pot being a safety hazard. I have read about the lee bottom pour pot leaking. Is there anything really bad about that, other than the mess?

I was planning on splurging for the lyman or rcbs lubrisizer thing but may start with the lee push through type for starters. I have done a little reading and watching about powder coating and I think will just start with the old proven lubing methods.

For now, I will be ordering some books and maybe some cerosafe to get chamber castings and figure out how to slug a barrel with a fishing weight.

Once again thank you everyone.

 

Mr. Farknocker

Re: So... I want to cast bullets
« Reply #12 on: June 03, 2015, 05:22:25 PM »
I was planning on splurging for the lyman or rcbs lubrisizer thing but may start with the lee push through type for starters. I have done a little reading and watching about powder coating and I think will just start with the old proven lubing methods.


As Old is probably aware, I've been fussing with the lube for a little while.  I was using Lee's tumble lube system with the bullets specifically designed for this (i.e., the micro lube grooves) in the beginning and even used it with bullets with regular lube grooves with some degree of success but wasn't completely satisfied with all of the leading that I was experiencing. I then tried the 45/45/10 method using Johnston's Paste Wax, Lee Liquid Alox and Mineral spirits with better success but still wasn't satisfied. I finally started pan lubing my bullets using a bees wax/paraffin/vaseline mix and was pleased with the results. I'm sticking to this method although its a PITA to set up and is very messy, leaving bits and pieces of wax all over the place. If I knew back when I started what I now know, I might have just sprung for a lubrisizer right off the bat. Since I've got everything set up and working now, however, I think I'll stay with the method I'm using and simply refine the process.

oldfart

Re: So... I want to cast bullets
« Reply #13 on: June 03, 2015, 05:56:36 PM »
I just got done reading about hi tek plastic coating. It sounds like a real pain.
http://gatewaybullets.com/product/hi-tek-lube-bullet-coating-kit/
What, Me Worry?

justin1098

Re: So... I want to cast bullets
« Reply #14 on: June 03, 2015, 06:20:52 PM »
I just got done reading about hi tek plastic coating. It sounds like a real pain.
http://gatewaybullets.com/product/hi-tek-lube-bullet-coating-kit/

From what I have learned, you can "tumble" the the powder on by filling tupperware containers with bullets and powder and putting them in a vibratory tumbler. You get full coverage but end up with inconsistent coverage that affects accuracy. Spraying on with a powder gun leaves you with nothing on the base and a "flange" around the base that has to be removed when you pull them off the pan.

oldfart

Re: So... I want to cast bullets
« Reply #15 on: June 03, 2015, 06:58:16 PM »
From what I have learned, you can "tumble" the the powder on by filling tupperware containers with bullets and powder and putting them in a vibratory tumbler. You get full coverage but end up with inconsistent coverage that affects accuracy. Spraying on with a powder gun leaves you with nothing on the base and a "flange" around the base that has to be removed when you pull them off the pan.
...
The stuff I was reading about was the 2 part liquid like epoxy.
That's the colorful stuff that a lot of guys here are shooting. You gotta mix it, coat the bullets then bake it on.
I don't know about the powder thing.

So the lee push thru gadget requires the bullet to be lubed separately, right?
I guess the intent is to use the lee liquid alox then push it through.
Since you would be installing gas checks, that actually sounds like a good idea.
What, Me Worry?

justin1098

Re: So... I want to cast bullets
« Reply #16 on: June 03, 2015, 08:21:47 PM »
Either way, The process seems new. I may jump on board if it goes more mainstream. I think I'll stick to the old ways.

oldfart

Re: So... I want to cast bullets
« Reply #17 on: January 14, 2017, 11:05:33 AM »

Tomorrow 1/15 afternoon
I'm willing to host a brief bullet casting session as an educational activity for anyone interested.
If you are interested and have some time let me know.
This would be at my place in Waipahu.
Send a pm if you are seriously interested.

Here is my plan....
Take some scrap metal and melt it.
Cast them into 45auto semiwadcutters.
Then take them and lubrisize as soon as they cool down.
Then load those  bullets into a medium velocity target load.
Then shoot them at khsc on Monday morning.

In other words, it would be a complete recycling activity.

What, Me Worry?

rfd

Re: So... I want to cast bullets
« Reply #18 on: January 15, 2017, 02:42:17 PM »
bottom pour or ladle - there really is no "versus" as it's all subjective.  for casting precise bpcr bullets in the 450 to 550 grain range, i prefer the ladle as it gives me better control of the mould and pour.  for casting most other bullets, bottom pour can be faster, particularly if yer running at least two moulds at once.
Molon Labe ~ NRA Life Member ~ NRA RSO ~ TMA

Inspector

Re: So... I want to cast bullets
« Reply #19 on: January 15, 2017, 04:59:39 PM »
I want to thank OF again for taking time out of his day to teach us how to properly cast bullets. He was very thorough and even made us work our asses off over a hot pot full of lead and made us cast about 200 bullets for him.  :rofl: :rofl: :rofl:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!