Towing a utility trailer (Read 4207 times)

Flapp_Jackson

Towing a utility trailer
« on: July 06, 2022, 02:48:20 PM »
Long post.  I added as much detail as I could so as to not waste time with too many questions going back and forth.

Hoping to get some opinions and maybe personal experiences from others.

Here's my question:  what amount of "drop" in my receiver's hitch do I need when towing a utility trailer with my Tacoma? 
Also, is an adjustable hitch worth the money versus having a couple of fixed drop hitches? Some cheaper adjustable one's have actually broken in two while towing a trailer.   Made in China, of course.  :shake:

Here we go!

I have a 2014 Toyota Tacoma 2x4 4-door Dual Cab w/4.0L 6 cyl engine and the Pre-Runner Sport Package.

All I'm missing of factory options for floor models is 4x4 drive and the tow package.

I'm looking at buying a landscaping utility trailer from HD.  Lowe's has one for cheaper, but the HD product looks like much better quality.

I just ordered a Class III hitch receiver from Amazon (CURT brand). it's made to install in the rear bumper brackets of my model truck -- no drilling or welding. I also ordered the custom wiring harness to power the trailer's lights.

I measured my bumper's clearance at 19", from the bottom of the bumper to the garage floor.

The trailer specs show the bottom of the tongue is 12" from the floor.

I found an installation video that shows 3.5" distance from bottom of bumper to center of receiver pin hole, or 2.5" from bumper to top of receiver.

Doing the math the way I understand it:  (19" ground to bumper) - (12" ground to trailer tongue) - (2.5" bumper to top of receiver hole) = 4.5" of "drop"

I know having a driver and maybe some cargo in the bed will lower the truck some, so I'm guessing 1"-2" of drop can be subtracted from the total.  I'll do another measurement with the truck under normal load once the receiver is attached.

That leaves 2.5" of drop from the receiver to the trailer tongue.  The standard 2" drop hitch is what most people buy for this truck, so that's about right.


Anyone have hints, tips or suggestions on what else I should be factoring in?  I've never owned a vehicle with a tow hitch before, so this is all new.  My main justification is the short bed of the truck. Not only is it just 5', but I have a retractable cover that takes up about a foot of that space, maybe more.  Good for Costco runs, not so much for green waste hauling or carrying sheet goods from HD without a rack.

My truck has a 1,000 lbs trailer weight rating (TWR) without a braking system or the tow package.  The HD/Karavan trailer is 517 lbs empty and has a cargo capacity of 1,483 lbs.

Which brings up another question:  will ~500 lbs of cargo capacity be worth the cost?  The Lowe's trailer is 375 lbs, but doesn't appear to be nearly as well made.

I considered renting a truck from HD, but for the amount of time I'd need it, I'd be spending close to the same in rental cost.  At least this way I get a trailer I can sell later and a trailer hitch that adds value if/when I sell my truck.

Thanks!

 :shaka:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

RSN172

Re: Towing a utility trailer
« Reply #1 on: July 06, 2022, 04:51:54 PM »
Having towed trailers almost everyday for 30+ years, I can tell you a short truck and long trailer is the easiest combo to backup.  I believe your Tacoma can tow up to 3500 lbs.  Trailers over 3k are supposed to have brakes. You want more weight in front of the axles than behind it.  Keep your trailer tongue weight in mind when loading. Get a reverse camera that can see the hitch. It will save you time and frustration hooking up.
Happily living in Puna

Flapp_Jackson

Re: Towing a utility trailer
« Reply #2 on: July 06, 2022, 06:59:26 PM »
Having towed trailers almost everyday for 30+ years, I can tell you a short truck and long trailer is the easiest combo to backup.  I believe your Tacoma can tow up to 3500 lbs.  Trailers over 3k are supposed to have brakes. You want more weight in front of the axles than behind it.  Keep your trailer tongue weight in mind when loading. Get a reverse camera that can see the hitch. It will save you time and frustration hooking up.

I knew I'd find a professional on here!   :thumbsup:

When I researched the various weight limits, I found many on the Interweb saying what you said -- 3,500 lb weight limit for my truck to pull.  But then I walked out to the truck and grabbed the owner's manual.  Here's what it tells me:



I circled the parts that apply to my truck model.  Everything looked good until I read the footnotes.  It says:
Quote
- Unbraked TWR*
1,000 lbs (450 kg)

*These models meet the tow-vehicle rating requirement of SAE International per SAE J2807.

When I looked up what TWR means in the manual, I found "Trailer Weight Rating".  I saw sites that called TWR "Tongue Weight Rating,"  but that's not how my manual reads:
Quote
TWR (Trailer Weight Rating)
- The maximum allowable Gross Trailer Weight, which is the weight of the trailer and any cargo in the trailer.

Given that, the manual seems to limit unbraked trailers to 1,000 lbs, which is lower than the 3,500 lbs allowed by the state before brakes are required, and the 3,000 lbs recommended by my manual for adding braking.  I guess it's just the difference between tow-vehicle and trailer limits -- not going to be the same very often I imagine.

Nothing's ever simple.

About tongue weight ... if I understand, that's a function of the hitch receiver limits, the limits of the hitch itself and the hitch ball limits, right? 

The hitch assembly I ordered that mounts to the truck has a 500 lb tongue wt limit.

I figure once I decide on the proper drop for the hitch, I just need to make sure the hitch and ball can handle at least 500 lbs if I want them to be capable of maximum weight capacity. 

What I read about tongue weight is it should be no less than 10% TWR and no more than 15% TWR.  Together, the trailer I'm looking at has a weight of 517 lbs. and a cargo capacity of 1483 lbs.  Total, that's 2,000 lbs exactly -- go figure.  I was wondering how they made the cargo capacity number so precise.

Anyway, that means the tongue weight range would be above 200 lbs and below 300 lbs maximum.  A 500 lb limit on the receiver tongue weight limit seems way more than sufficient.

Then there's the hitch limits.  I know it's a combination of length and manufacturing specs.  There's one on Amazon also from CURT with a 2" drop and rated at 750 lbs tongue weight / 7,500 Gross Trailer Weight.  I looked up the specs for the hitch ball that it comes with, and it's also rated for 7,500 lbs.

If everything is within limits (trailer and cargo weights), then I think the main issue for tongue weight depends on balancing the load over the axle, with the proper distribution over the tongue -- 10%-15% more forward than over the rear of the trailer.

I think that's right.  This is giving me a headache!  Going for Tylenol .....   :wacko:

The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #3 on: July 06, 2022, 07:13:38 PM »
BTW, it you take the max limit of 3,500 lbs (with braking using my truck), 14% of the max trailer weight is 490 lbs, which puts you still within the stated max tongue limit for the hitch receiver, and still way under the 750 lb limit for the hitch I'm considering.

So, if I ever add breaking and nothing else from the tow package engine upgrades, what I'm planning to add would meet or exceed the 3,500 lb TWR requirements.

This actually sounds like a possibility, just to get the most cargo capacity from the trailer so there's no problems overloading it.

I'd have the option to tow a larger trailer if needed (one with a higher TWR limit)  up to the full 3,500 lbs and satisfy the state requirement for braking, too.

Now I need to see if trailers with breaking are even available.

 :thumbsup:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #4 on: July 06, 2022, 08:03:55 PM »
Okay, more research done.

Looks like the 1,000 lb unbraked limit is a common theme among most Toyota trucks.  It appears to be about saving the brakes on the truck and avoiding damage as opposed to the tow-vehicle's ability to manage a heavier trailer.

Lots of posts on message boards said they tow up to 2,000 lbs easily with no trailer brakes.  They have to give themselves a little extra stopping distance, and any sudden acceleration or emergency stopping could be problematic.

Other than that, there's nothing I can find that prohibits unbraked trailers up to Hawaii's law that limits them at 3,000 lbs -- less than the 3,500 lbs Toyota says you can tow without the tow package upgrades.

I don't know how expensive adding brakes to an unbraked trailer would be, but some estimate it around $450 to replace the axle and add the braking hubs and controllers.

Plus, the wiring harness from the truck would need to be upgraded to the 7-pin version from the 4-pin.

I found that they now have Bluetooth enable wireless breaking controllers, but you need the appropriate tow-vehicle connector to plug it in.  It then controls breaking on the trailer without the need for wires between the trailer and the truck.   :geekdanc:

This towing thing is becoming a hobby unto itself!   :rofl:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

RSN172

Re: Towing a utility trailer
« Reply #5 on: July 06, 2022, 10:45:33 PM »
FYI, transfer stations are not accepting trailers till at least the end of the year.
Happily living in Puna

Flapp_Jackson

Re: Towing a utility trailer
« Reply #6 on: July 07, 2022, 01:30:16 PM »
FYI, transfer stations are not accepting trailers till at least the end of the year.
Thanks!  That's very helpful info.

The state website says the "no trailers" rule applies to the 3 transfer stations and 6 convenience centers.  I think it applies to green waste contractors, too, but I called the Hawaii Earth Recycling location in Wahiawa to verify.  Waiting on a call back.

Green waste hauling was a major "need" for a trailer.  I'm sure I'll still use it for lumber and drywall, just not as often as I planned.

They are also limiting residential customers to 2 pick-up sized loads per day.  I remember going 3-4 times in a day when I had trees to remove.

I guess I can pace myself now.   :geekdanc: :thumbsup:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #7 on: July 09, 2022, 10:56:55 AM »
Well, still no cal back from the green waste folks.  I'll just take a load in the pickup and ask in person.

I did receive one Amazon package via UPS this week 2 days after ordering.  That would be the wiring harness that will add a 4-pin connector to the rear lights of my truck.  No cutting or splicing.  Just unplug the existing connectors on each taillight, reconnect them with the harness connectors between truck wiring and taillights, and screw the ground wire to the frame.

I went onto the CURT website to see what they'd charge to ship the hitch receiver here.  It was predictably over $100.  Kind of painful for a part that only costs $130.  So, I checked Amazon.  I paid $127 + tax w/free Prime shipping.   :thumbsup:  It was originally scheduled to be delivered yesterday.  After it shipped via USPS First Class Mail, it was updated to July 15th.  A day or so after that, tracking said delivery was scheduled for Monday, the 11th.  It's now out for delivery TODAY, the 9th!   :thumbsup:  I must be living right, or something.   :D

I'll install it today and measure the amount of drop I need in the hitch.  I'll probably get a hitch from Amazon, too.

Both the 2" and 4" drop CURT hitches run about $30 on Amazon with the 2" ball.  Looking at HD, they want about double that for TowSmart brand hitches. 

Also, I'lll order a locking hitch pin when I order the hitch today.  I saw a story where someone stopped at a rest area pulling their RV Trailer.  Someone apparently removed the cotter pin and hitch pin.  No way do hitch pins fall out that have a decent cotter pin installed  They were able to stop safely after they noticed the trailer swaying.  Luckily, they used the "criss-cross" method when hooking up the safety chains, which kept the trailer tongue from hitting the pavement (Trailer tongue was supported by the chains).

I added a locking hitch pin to my cart already, to keep someone from walking off with the hitch anytime it's left on the truck -- which won't be very often.  I've seen other reports that some thieves will disconnect the hitch from the receiver in order to steal a trailer/camper/boat locked to the ball by pulling a truck of their own up to it and using their receiver with your hitch. 

The CURT locking hitch pin is $20.52.  I know I'm sounding like an ad for CURT products, but from what I see, their products are well made, long lasting and affordable.  Plus, they sell on Amazon which saves me high shipping costs.

I'll still have time to compare the trailers at Lowe's and HD before I have the hitch.  If I'm lucky, maybe I'll see one on Craig's List this week.
« Last Edit: July 09, 2022, 11:12:37 AM by Flapp_Jackson »
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #8 on: July 09, 2022, 07:13:01 PM »
USPS had a new and very young carrier delivering today.  Normally I expect the mail about 12-1, but she arrived after 4:30.  When I didn't see my big box, I asked if she had seen it.  She said no, and didn't bother to call anyone find out.  I imagine she was running late for obvious reasons.

Just after 6, my doorbell rang.  Not one, but two delivery trucks were out front.  I assume one was a supervisor, and the other was finishing up to other carrier's route for her.

Anyway, the receiver arrived in a large box.  Small gash the side of the box, but the only real damage is a tiny bit of paint scraped.  I can fix that with some Krylon.

The shipping weight is 48 lbs, and the hitch receiver weight is 41 lbs.  Add the hitch and ball, and that's about 50 lbs total.

This is why I waited to order the hitch.  The weight of the new parts, plus me, plus a little more for "cargo" in the truck bed, and I'm sure the amount of drop needed for the hitch will change.

Now that they arrived late, my project will have to wait until tomorrow.  But, at least they showed up.

The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

robtmc

Re: Towing a utility trailer
« Reply #9 on: July 11, 2022, 05:34:00 PM »
Hope your neck is more flexible than mine.

While we had a boat, I always let my wife do the towing and backing up.  I just could not move around easily enough to be safe.   
She got a pretty good handle on backing up down a boat ramp.

Flapp_Jackson

Re: Towing a utility trailer
« Reply #10 on: July 11, 2022, 06:45:40 PM »
Hope your neck is more flexible than mine.

While we had a boat, I always let my wife do the towing and backing up.  I just could not move around easily enough to be safe.   
She got a pretty good handle on backing up down a boat ramp.

I can manage to swivel enough to see behind me.  Getting a little stiffer with age, but I can ignore the minor pain for a short time.  If not, I'll get a spotter or do a walk-around before moving.

Since I'm here, I'll provide an update.

The hitch receiver was a bear trying to get it in place on the frame. I finally went to the Amazon reviews and found the solution.

During storage and transit, many of these receivers have one or both brackets get a little bent.  I checked mine with a square, and one looked perfect.  Here's what the other side looked like:



I used a couple of 2x4 blocks and a jack to spread them apart, but a BFH would have worked, too.  Oh, well.  Nothing's ever as easy as you'd hope.

So, then  I looked for the torque specs on the bolts ... 4 that came with the receiver, and the 10 that hold the bumper arm to the bumper and frame.  All the 2002 instruction sheet has refers to one setting for the 10mm bolts and a higher setting for the 12mm.  The bolts I have are 17mm and 19mm, so off the the interwebs again.

Best guess was use the higher and lower torques for the frame bolts vs the bumper connected bolts.  I wound up having to lower the spare to get the torque wrench where I had room to work.  Didn't require that before torquing.

The 10 17mm bolts attached to the frame (6 OEM & 4 new) needed 86 ft/lbs. OMFG!  What a workout -- upside down on the garage floor, pushing on one side and pulling on the other.  I thought the wrench was broken and would never find the torque I set it to.

Of course, one bolt had to act up and sheered off.  Luckily it protruded through the brackets and frame enough for me to use a 10mm socket and drive it through until it dropped.  Now I need to drive to the dealer and get a new bolt.   :grrr:

I also took time to make sure the bumper was even with the tailgate.  It wasn't at first, so before I torqued those remaining 4 bolts, I leveled it out.  The bumper bolts only needed 48 ft/lbs.  That was nothing compared to the first 10!  I'll consider that my cool-down workout.   :geekdanc: :thumbsup:

Measuring the receiver (finally!), I have an 18.5" distance from top of receiver hole to floor.  I got into the truck and loaded some weight in the bed, and it only dropped half an inch.  I'll go with 18" for now.

Given the trailer I'm buying is 13" from bottom of coupler to ground, that means I have a drop of 5".  I was hoping the 2" drop hitch would be ok, but now it's looking like a 4" drop is needed at least.  I know the weight of the trailer tongue will press down on the rear of the truck, so I'm guess an inch or two less than 5".

I'm shopping around for adjustable hitches.  They run anywhere from just under $100 to over $300 or $400, depending on the longest drop you want.  Some also have multiple ball sizes included.  Versatility ain't cheap!

I'm still looking at the 4" Curt hitch for $25 on Amazon.  Comes with a 2" ball and hitch pin.  I've already bought a locking hitch pin, but that'll be good for a spare if the other gets lost.

So, in short, the receiver is installed less one broken OEM Tacoma bolt, and its height is about what I expected from research.  I'll be installing the taillight wiring harness tomorrow and see about a replacement bolt.  Then I'll be all set to shop for a trailer!

Of course, there are lots of uses for a tow hitch receiver other than trailers with boats, ATVs, lumber, and lawn equipment. You can attach a bike carrier, cargo rack, hammock chair supports, grills, flat screen TVs, tables that extend the surface area of your tailgate for ... tailgating, locking secure storage for money, credit cards and keys when you aren't able to carry it on you, steps to assist getting into the bed, and I'm sure a million other things.

https://www.doityourselfrv.com/tow-hitch-accessories/

86 ft/lbs x 10 bolts in close quarters and awkward positions .... not a picnic!   :rofl:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

RSN172

Re: Towing a utility trailer
« Reply #11 on: July 11, 2022, 08:54:25 PM »
Hope your neck is more flexible than mine.

While we had a boat, I always let my wife do the towing and backing up.  I just could not move around easily enough to be safe.   
She got a pretty good handle on backing up down a boat ramp.
Get used to using your side mirrors to back up.  I can parallel park a trailer between two cars if the space is at least 8 ft longer than the truck and trailer.
Happily living in Puna

Flapp_Jackson

Re: Towing a utility trailer
« Reply #12 on: July 11, 2022, 10:57:08 PM »
Get used to using your side mirrors to back up.  I can parallel park a trailer between two cars if the space is at least 8 ft longer than the truck and trailer.

I used to drive a school bus with 13 mirrors.  When I had to take my bus to the maintenance facility, they had me park between 2 buses that barely had room for the doors to open on mine and the one to my left!

I do have a rear back-up camera on the tailgate handle.  Very handy since my garage is so small.  Only problem with it is when I haul large loads with the tailgate down.  Not a useful angle!   :geekdanc:
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #13 on: July 11, 2022, 11:06:08 PM »
I just spent hours looking at adjustable "drop" hitches/ball mounts.  I almost settled on a $40 one, but something told me not to.  All the rest I seriously considered were just under $100 or up to $200.

So instead I ordered 2 -- a 4" and a 6" drop.  Both come with the same 2" ball rated for 6,000 lbs, and both are Curt products. Not having an adjustable one also eliminates the chance of theft of the ball mount.  Even though the adjustable hitches can use the standard locking hitch pin, the ball mount is held on by usually 2 more pins that are rated for the max load of the trailer without the receiver helping it.  Cut sells a channel adjustable model they say only works with their $80 locking pin set: one to replace one of the two ball mount pins, and one for the normal hitch pin.

I THINK I need the 6", but I'm getting a 4" just to be safe.  If I find one works better, I could return for a refund, but I'll like keep for a time I'm going to need it.

I think trying to get a trailer that is only 2,000 lbs total trailer weight with cargo perfectly inline with the truck receiver is overkill.  1" too high or too low isn't going to be a safety hazard.
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #14 on: July 13, 2022, 09:23:42 PM »
Alright, someone is telling me I shouldn't have ordered the 4" drop and 6" drop hitches.  Got a message today the package was "damaged in transit" before it departed CA for HNL.  No idea what was damaged, but they are sending the package back to the shipper (Amazon) and will issue a refund when it arrives.

Funny.  I  figured this of all my Amazon packages would have gone off without a hitch!   :rofl: :rofl:

Even though I ordered the "fixed drop" hitches, I was still looking into adjustable ones. Something told me with as many variables as there are with trailers, tow vehicles and cargo weights, I'd be better off getting something that's able to adjust to changes in ... everything.

I almost got the B&W Tow&Stow.  If I were towing a boat, camper, or horse trailer, that's where I'd be looking.  For $235 or more, my needs better be more than a single trailer.

Instead, I went with the Curt Channel Mount Hitch.  I like it because it only allows one trailer ball at a time. The ones with 2 or 3 different size balls is nice for switching what you're towing, but if I only need a 2" diameter ball, the dual and tri versions have the 2" up while another is hanging down.  Cue the hanging ball jokes!  But that reduces ground clearance under the hitch for no good reason.

Also, the channel design offers a shorter hitch that the ball mount connects to.  If you aren't using the maximum drop, then the ball mount and hitch are giving better ground clearance than a fixed 6" hitch and mount.

After reading and viewing info on weighing the trailer's tongue and what minimum ground clearances are needed for a hitch, the light finally went on.  When I measured the receiver-to-ground, I had the truck partially outside the garage.  I was inside measuring, but the front wheels were on the driveway -- sloping down.  I remeasured, and the receiver is now at 17.75".  I lost 3/4" of height by making the truck level.  Duh!

That new measurement actually helps, because it means I can get by with a 5" drop hitch.  Since most are made in 2" increments, a 6" is the choice -- it'll offer the best range of heights (drops) for many trailers from a 6 3/4" drop to a 5 1/4" rise.

Ordered it from Amazon w/Prime shipping for $90.05 + tax.  That's about $25 more than the 4" drop and 6" drop hitches.  $35 more if you include the ball I had to buy separately.  Basically, the adjustable sans ball is about the same as 3 separate hitches with 2" balls included.  Still it's about a third the cost of the Tow&Stow I wanted.

The Curt adjustable channel mount hitch has 1" increments, making it more likely you can get the trailer inline with the tow vehicle.

So much fun!
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #15 on: July 15, 2022, 11:58:41 PM »
Picked up the replacement bolt from the Waipahu Toyota parts department.  $2.86.  It's a "special" part, with a washer permanently attached -- the bolt is slightly smaller in diameter at the top than the rest of it.

While the power was out in my part of the island, I installed the bolt and the wiring harness.  I also checked the fit of the hitch lock pin.

The harness was no problem.  Used a multimeter, and the running lights, left & right signals, and brakes all showed a current on the correct pin.   :thumbsup:  CURT sells a bracket for the 4-pin connector to keep it from dangling.  It's less than $2.  They make different brackets to fit a variety of plugs and tow vehicles.  If you want their optional bracket that zip-ties onto the receiver and then screws into the wiring bracket, that'l run you about $14!  I'll be fine drilling a couple of holes in the frame. For now, it's hanging in the safety chain loop.

All in all, not counting the wire bracket, I've spent $364 installing the hitch and wiring.  It would have been about $45 less if I'd gone with the fixed drop ball mount vs. the adjustable one.  I also spent $30 on an anti-rattle bracket to keep the hitch from moving in the receiver.  So, if someone were to follow my example, it can easily be done for less than $300.

Considering I saved $$ by DIY-ing it, and the quality is better than I'd hoped at this price point, I'm happy with it so far.

Still awaiting the adjustable hitch, ball, grease (gotta have slippery balls!), and the hitch receiver plug for when it's not being used,

As for the locking hitch pin, I've seen videos where someone can use a pipe of the right diameter on these types to bend the lock part off.  I also saw more than one take a sawzall to it and be done in seconds.  Since the pin fits 2" and 2.5" receivers, there's a gap on my 2" pin where a saw blade can easily be placed on thinner part of the pin.

 I'm thinking of at least putting a couple of stainless steel washers to reduce the gap so a sawzall blade won't fit between the receiver and either "neck" of the pin.  I was also trying to come up with something to stop a pipe from fitting around the locking end.  Maybe add some bolts through holes in the washer that interfere with any pipe being placed over it?  Would make the bolts shorter than the locking cylinder so they couldn't get any leverage on the bolts, and the bolts wold be tall enough to prevent leverage between themselves and the end of the cylinder.

Hey! The power's back!   :geekdanc: :thumbsup:

« Last Edit: July 16, 2022, 12:11:24 AM by Flapp_Jackson »
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

Flapp_Jackson

Re: Towing a utility trailer
« Reply #16 on: July 23, 2022, 01:05:19 PM »
My CURT Channel Hitch and Ball Mount arrived from Amazon today.

Really happy I chose this one.  The hitch that the mount connects to only drops about 3.5" below the bottom of the receiver, which gives me double the clearance of the B&W Tow & Stow not including the second ball that can sit below the hitch.

I was right on the 9" recommended minimum clearance from ground to lowest hitch point, so this one gives me an extra 4" or more to spare.

The design increases the drop to a maximum of 6-3/4", which should meet my needs perfectly.  And with 1-inch spacing between adjustment holes, it makes finding the best drop/rise easier and more accurate.

Now I need to pick up a 1-1/2" socket and a torque wrench.  My wrench only torques up to 150 ft lbs, which has been plenty up until now.  The nut that holds the ball to the mount requires 250 ft lbs of torque!  HD has a Husky model for about $50.

I'll probably sell my other wrench.  It's relatively new, only used to install running boards and the hitch receiver on my Tacoma.

In addition to the single ball mount that I bought, they also offer a dual ball version (still has that clearance issue if adjusted low with 1 ball pointed South), and other accessories that connect to the 2-channel hitch -- folding hitch step, wench brackets and tow rings.

Curt has several designs of adjustable mounts in various sizes.  Seemed like adjustable is the best solution unless you only intend to tow the same thing exclusively like a boat trailer.


The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

robtmc

Re: Towing a utility trailer
« Reply #17 on: July 23, 2022, 02:32:42 PM »
Still awaiting the adjustable hitch, ball, grease (gotta have slippery balls!), and the hitch receiver plug for when it's not being used,
Hint:  If you do not care for grunge, wipe the ball down after use.  Picks up a lot of road crap otherwise. 

I sliced up a tennis ball to slip over it when bare.

I just got a big farking wrench  from HD for my ball hitch, not calibrated torque other than German torque (gutentite)
Never loosened after several years of limited boat pulling.
« Last Edit: July 23, 2022, 02:54:52 PM by robtmc »

Flapp_Jackson

Re: Towing a utility trailer
« Reply #18 on: July 23, 2022, 05:28:36 PM »
Hint:  If you do not care for grunge, wipe the ball down after use.  Picks up a lot of road crap otherwise. 

I sliced up a tennis ball to slip over it when bare.

I just got a big farking wrench  from HD for my ball hitch, not calibrated torque other than German torque (gutentite)
Never loosened after several years of limited boat pulling.

Since my paranoia that someone will disconnect and take anything hitch-connected, I'll probably not install the hitch to the receiver unless I'm towing.  I'm looking for ways to secure the pins on the channel mount without paying $80 for the locking set CURT says are needed to replace the pins.
The reasonable man adapts himself to the world;
the unreasonable one persists in trying to adapt the world to himself.
Therefore, all progress depends on the unreasonable man.
-- George Bernard Shaw

robtmc

Re: Towing a utility trailer
« Reply #19 on: July 23, 2022, 07:37:44 PM »
I used a simple pin that you could slip a small padlock onto to lock the ball to the receiver.  Had another locking pin for when the trailer was on the ball.
If you were on  the BI you could have them..