Hope your neck is more flexible than mine.
While we had a boat, I always let my wife do the towing and backing up. I just could not move around easily enough to be safe.
She got a pretty good handle on backing up down a boat ramp.
I can manage to swivel enough to see behind me. Getting a little stiffer with age, but I can ignore the minor pain for a short time. If not, I'll get a spotter or do a walk-around before moving.
Since I'm here, I'll provide an update.
The hitch receiver was a bear trying to get it in place on the frame. I finally went to the Amazon reviews and found the solution.
During storage and transit, many of these receivers have one or both brackets get a little bent. I checked mine with a square, and one looked perfect. Here's what the other side looked like:

I used a couple of 2x4 blocks and a jack to spread them apart, but a BFH would have worked, too. Oh, well. Nothing's ever as easy as you'd hope.
So, then I looked for the torque specs on the bolts ... 4 that came with the receiver, and the 10 that hold the bumper arm to the bumper and frame. All the 2002 instruction sheet has refers to one setting for the 10mm bolts and a higher setting for the 12mm. The bolts I have are 17mm and 19mm, so off the the interwebs again.
Best guess was use the higher and lower torques for the frame bolts vs the bumper connected bolts. I wound up having to lower the spare to get the torque wrench where I had room to work. Didn't require that before torquing.
The 10 17mm bolts attached to the frame (6 OEM & 4 new) needed 86 ft/lbs. OMFG! What a workout -- upside down on the garage floor, pushing on one side and pulling on the other. I thought the wrench was broken and would never find the torque I set it to.
Of course, one bolt had to act up and sheered off. Luckily it protruded through the brackets and frame enough for me to use a 10mm socket and drive it through until it dropped. Now I need to drive to the dealer and get a new bolt.

I also took time to make sure the bumper was even with the tailgate. It wasn't at first, so before I torqued those remaining 4 bolts, I leveled it out. The bumper bolts only needed 48 ft/lbs. That was nothing compared to the first 10! I'll consider that my cool-down workout.

Measuring the receiver (finally!), I have an 18.5" distance from top of receiver hole to floor. I got into the truck and loaded some weight in the bed, and it only dropped half an inch. I'll go with 18" for now.
Given the trailer I'm buying is 13" from bottom of coupler to ground, that means I have a drop of 5". I was hoping the 2" drop hitch would be ok, but now it's looking like a 4" drop is needed at least. I know the weight of the trailer tongue will press down on the rear of the truck, so I'm guess an inch or two less than 5".
I'm shopping around for adjustable hitches. They run anywhere from just under $100 to over $300 or $400, depending on the longest drop you want. Some also have multiple ball sizes included. Versatility ain't cheap!
I'm still looking at the 4" Curt hitch for $25 on Amazon. Comes with a 2" ball and hitch pin. I've already bought a locking hitch pin, but that'll be good for a spare if the other gets lost.
So, in short, the receiver is installed less one broken OEM Tacoma bolt, and its height is about what I expected from research. I'll be installing the taillight wiring harness tomorrow and see about a replacement bolt. Then I'll be all set to shop for a trailer!
Of course, there are lots of uses for a tow hitch receiver other than trailers with boats, ATVs, lumber, and lawn equipment. You can attach a bike carrier, cargo rack, hammock chair supports, grills, flat screen TVs, tables that extend the surface area of your tailgate for ... tailgating, locking secure storage for money, credit cards and keys when you aren't able to carry it on you, steps to assist getting into the bed, and I'm sure a million other things.
https://www.doityourselfrv.com/tow-hitch-accessories/86 ft/lbs x 10 bolts in close quarters and awkward positions .... not a picnic!
