Giraud tri way trimmer or worlds finest (Read 20052 times)

rklapp

Re: Giraud tri way trimmer or worlds finest
« Reply #20 on: April 17, 2017, 04:21:47 PM »
As long as your brass sizing is consistent and accurate indexing off the shoulder of the case for trimming is fine. Shoulder to base dimensions sets headspace which is what one is after as far as shot to shot consistently. Neck trim off a thou or two isn't the end all for accuracy.  If it's off a lot, it could cause issues.  Any of the trimmers mentioned is well capable of doing the job.
I use the Giraud trimmer, it gets the job done quickly and easily.
I tend to be picky with my COAL for my .223. If the case doesn't touch the trimming tool (2.250") or within 2 thousandth, I toss it. Federal cases are always too short. I'm gonna try measuring the shoulder to base length and see if that starts to bother me. You bastards already have me thinking about replacing my standard trigger. When will this torment end???

Yahh! Freedom and justice shall always prevail over tyranny, Babysitter Girl!
https://ronsreloading.wordpress.com/

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #21 on: April 17, 2017, 06:37:13 PM »
Rklapp
Now you have me wondering

I don't know if this is right.  I have to run this by my mentor.  (The only thing is he only shoots semi so he always does a full length sizing but I'm loading for bolt gun)

For my fired brass, if the rim passes the min /max for the case gauge but the mouth > max on the gauge, I was planning to trim indexing off the shoulder. 

The shoulder of fired brass may not exactly match the shoulder of FL sized brass, but after trimming I was going to check it again in the case gauge.  If the mouth is within min/max of the case gauge, it should be ok right?

I would neck size a few times (3?) before doing a FL sizing.   Plan is to anneal each time after I do a FL sizing and trimming.  After FL sizing/annealing, I would load a cheaper bullet to shoot and produce fired brass.  Plan is to use only neck sized fired brass for load development.

I probably have this all mixed up after trying to learn reloading off the web

Heavies

Re: Giraud tri way trimmer or worlds finest
« Reply #22 on: April 17, 2017, 07:01:49 PM »
Rklapp
Now you have me wondering

I don't know if this is right.  I have to run this by my mentor.  (The only thing is he only shoots semi so he always does a full length sizing but I'm loading for bolt gun)

For my fired brass, if the rim passes the min /max for the case gauge but the mouth > max on the gauge, I was planning to trim indexing off the shoulder. 

The shoulder of fired brass may not exactly match the shoulder of FL sized brass, but after trimming I was going to check it again in the case gauge.  If the mouth is within min/max of the case gauge, it should be ok right?

I would neck size a few times (3?) before doing a FL sizing.   Plan is to anneal each time after I do a FL sizing and trimming.  After FL sizing/annealing, I would load a cheaper bullet to shoot and produce fired brass.  Plan is to use only neck sized fired brass for load development.

I probably have this all mixed up after trying to learn reloading off the web
1.  you never want the neck to extend past the mouth of the case gage.  The neck could get jammed into the lead of the rifling causing dangerous pressure spikes.  Shorter is ok but over the max is a no go.
2. If you only neck size and develop a load, when you FL size (as you must eventually) you may have a point of impact shift or group size change for that load.  This is why I FL size the body of the case MINIMALLY each and every time I reload the case.  Bumping the shoulder back .002" .003" everytime means consistent ammo everytime.

I use a redding body die first to bump the shoulder of the case back .002" to .003".  This die doesn't excessively resize the body of the case.  I use a very light coating of Kiwi mink oil as a case lube on the body of the case, I try not to get any on the shoulder portion of the neck.  If there is a bunch of lube over there the shoulder,  the case can get sized more than desired.

Then I use a Lee mandrel neck sizer die to size and straighten the neck. 

Clean off the lube using Oldfarts non clorinated brake cleaner method.

Then trim using the Giruad triway trimmer.

Ammo I make using this method has very minimal to no runout, I never have a hard to chamber round, and every bullet is consistent in impact and accuracy.  Fast easy and efficient reloading.  Once everything is set up and locked down no need to fuss.

ren

Re: Giraud tri way trimmer or worlds finest
« Reply #23 on: April 17, 2017, 07:14:36 PM »
I tend to be picky with my COAL for my .223. If the case doesn't touch the trimming tool (2.250") or within 2 thousandth, I toss it. Federal cases are always too short. I'm gonna try measuring the shoulder to base length and see if that starts to bother me. You bastards already have me thinking about replacing my standard trigger. When will this torment end???



I think you are over analyzing. Federal 223 cases are soft, stretchy things. You'd be surprised at how .223 will shoot without lamenting about all these factors.

....
Get to the choppa!

That was the first Predator.
I was watching PredatorS. The one with Adrien Brody and Alice Braga. :thumbsup:
Deeds Not Words

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #24 on: April 17, 2017, 08:02:00 PM »
Heavies,
Interesting.  I had thought FL sizing each time was basically for semi's for reliable feeding/extraction and neck sized fired brass was for better accuracy.

Sorry for confusion, I thought the top of the case was the mouth.

Your right, the FL sized case would not be consistent with neck sized cases so I was planning to load a cheap bullet to shoot....just to produce fired brass that would be used for load development

I'll give your method a shot.  It is consistent/same each time and makes reloading more kiss since I wouldn't need to size 2 different ways or keep track of the # of times I have neck sized a case

If I FL size each time, is it ok if l anneal only when I have to trim.....or say every 3rd sizing?
My coworker's husband has a giraud and will anneal my cases but i don't want to bother him too much.   

I could wait till I have a bunch to anneal....like several hundred cases.....bad idea?

Tnx!

Heavies

Re: Giraud tri way trimmer or worlds finest
« Reply #25 on: April 17, 2017, 08:16:10 PM »
Heavies,
Interesting.  I had thought FL sizing each time was basically for semi's for reliable feeding/extraction and neck sized fired brass was for better accuracy.

Sorry for confusion, I thought the top of the case was the mouth.

Your right, the FL sized case would not be consistent with neck sized cases so I was planning to load a cheap bullet to shoot....just to produce fired brass that would be used for load development

I'll give your method a shot.  It is consistent/same each time and makes reloading more kiss since I wouldn't need to size 2 different ways or keep track of the # of times I have neck sized a case

If I FL size each time, is it ok if l anneal only when I have to trim.....or say every 3rd sizing?
My coworker's husband has a giraud and will anneal my cases but i don't want to bother him too much.   

I could wait till I have a bunch to anneal....like several hundred cases.....bad idea?

Tnx!

No problem.  I do also agree with you on using a cheap bullet to get the case to size exactly to the chamber.  I do that also with my new brass.  I fireform the case to the rifles chamber.  Then the next cycle is load development with those cases. 

The hard part is measuring the base to shoulder.  I have been using the Larry Willis tool for measuring both case shoulder and OAL to bullet ojive.  Measuing to the tip of the billet is useless.  The ojive is the part that matters to the OAL of the cartridge.  This tool is my most used measuring device and is very precise and repeatable.  I've tried other, but they don't come close to the ease of this tool.  http://www.larrywillis.com/OAL.html

I'd anneal every loading to make the case last longer.  But I already have a machine.  I also run the case in the trimmer everytime, most times it just skims a little, but that just gives me the peace of mind.

Inspector

Re: Giraud tri way trimmer or worlds finest
« Reply #26 on: April 17, 2017, 08:37:42 PM »
Federal 223 cases are soft, stretchy things. You'd be surprised at how .223 will shoot without lamenting about all these factors.
:thumbsup: :thumbsup: :thumbsup:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #27 on: April 17, 2017, 10:39:37 PM »
Heavies,
I see

For new brass, you fireform it and then bump the shoulder back with a body die about 0.002" to 0.003" from it's fired size.

So it is basically a fire formed case....with the shoulder pushed back a little

Did I get it?

Heavies

Re: Giraud tri way trimmer or worlds finest
« Reply #28 on: April 18, 2017, 08:46:22 AM »
Heavies,
I see

For new brass, you fireform it and then bump the shoulder back with a body die about 0.002" to 0.003" from it's fired size.

So it is basically a fire formed case....with the shoulder pushed back a little

Did I get it?
Roger that.  After fireforming to that particular rifle, push shoulder back .002".  Looking at my notes, for bolt gun it was .0015" to .002.  For semi automatic, .003 to .004"

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #29 on: April 18, 2017, 11:25:31 PM »
Tnx Heavies!

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #30 on: April 19, 2017, 06:08:49 AM »
Heavies
For the Redding body sizer do you use 75111 or 74111 (small body) or 75907 (40 degree)?

The Lee collet neck sizer is part 90954?

Thx!

Heavies

Re: Giraud tri way trimmer or worlds finest
« Reply #31 on: April 19, 2017, 06:42:30 AM »
Heavies
For the Redding body sizer do you use 75111 or 74111 (small body) or 75907 (40 degree)?

The Lee collet neck sizer is part 90954?

Thx!

I use the dies in .308, but If you have a normal size chamber 75111 normal body die should be fine.  You have a .223/5.56 chamber correct?

The 40 degree is for a different cartridge, the 40 degree ackley improved, not what you want.

Lee 90954 is correct

tim808

Re: Giraud tri way trimmer or worlds finest
« Reply #32 on: April 19, 2017, 01:03:26 PM »
Yes - I have a ruger American predator in 223

Tnx Heavies!

Rocky

Re: Giraud tri way trimmer or worlds finest
« Reply #33 on: April 19, 2017, 08:53:57 PM »
....
I dunno about yours, but mine gets shorter as it gets older   :rofl:


Your not polishing it enough !   :rofl:

 :wave:
“I ask you to judge me by the enemies I have made.”
                                                           Franklin D. Roosevelt

oldfart

Re: Giraud tri way trimmer or worlds finest
« Reply #34 on: April 19, 2017, 09:51:31 PM »
Your not polishing it enough !   :rofl:

 :wave:
...
Got some experience in that hmmmm?
What, Me Worry?

Inspector

Re: Giraud tri way trimmer or worlds finest
« Reply #35 on: April 20, 2017, 04:18:13 AM »
Your not polishing it enough !   :rofl:

 :wave:
If you use Flitz, you don't have to polish as long to get the same results.  :rofl: :rofl: :rofl:

Hi Rocky  :wave:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!

Rocky

Re: Giraud tri way trimmer or worlds finest
« Reply #36 on: April 20, 2017, 03:02:31 PM »
If you use Flitz, you don't have to polish as long to get the same results.  :rofl: :rofl: :rofl:

Hi Rocky  :wave:

Is Flitz the name of that ex-Girlfriend you won't tell s about ?  :rofl: :rofl:
 :wave:
“I ask you to judge me by the enemies I have made.”
                                                           Franklin D. Roosevelt

Inspector

Re: Giraud tri way trimmer or worlds finest
« Reply #37 on: April 21, 2017, 04:16:01 AM »
Is Flitz the name of that ex-Girlfriend you won't tell s about ?  :rofl: :rofl:
 :wave:
:rofl:  :rofl: :rofl:
SCIENCE THAT CAN’T BE QUESTIONED IS PROPAGANDA!!!